Belmont Clesta II Manuale utente

CLESTA II CHAIR (EURUS TYPE)

INSTALLATION INSTRUCTIONS

1 Safety Consideration

2 Cautions regarding installation

1-1 Risk Level Interpretation ............................................................ 3

1-2 Safety Precautions ..................................................................... 5

2-1 Precautions for installation ..........................................................6

4 Installation

4-1 Dimensions/Environmental Requirements ...................................8

4-1-1 Dimensions ..............................................................8

4-1-2 Environmental Requirements ....................................8

4-2 Necessary tools and supplied parts ............................................9

4-2-1 Necessary tools ........................................................9

4-2-2 Supplied parts ..........................................................9

4-3 Installation procedures .............................................................10

4-3-1 Installing the chair ...................................................10

4-3-2

Installing the seat, backrest, and other parts of the chair

...14

4-3-3 Attaching the cover ................................................18

3 Conditions for installation site

3-1 Capacity of power supply equipment to be used ........................7

3-2 Strength of the building required for installation ..........................7

Table of Contents

5 Flow Diagram/Wiring Diagram

5-1 Flow Diagram ...........................................................................20

5-2 Wiring Diagram .........................................................................21

1 Safety Consideration

1-1 Risk Level Interpretation

CONTRAINDICATION

Precautions before use

Classification by degree of

harm or damage and urgency

Make sure to carefully read the Safety Precautions and Operat-

ing Precautions and use the product correctly.

Use of the product without regard to this indication will create

a hazardous condition that may result in death or serious

injury.

These precautions are intended to ensure the safe use of the

product and prevent harm or damage to users or other people.

According to the magnitude of harm and damage and the degree

of urgency, an incident that may be caused by misuse of the

product is classiﬁed into one of the following categories:

CONTRAINDICATION, WARNING, and CAUTION.

All of these categories are important for safety. Always follow the

instructions provided.

We assume no responsibility for any accident due to failure to

follow the Safety Precautions even in the event of harm or damage

to users or other persons.

In such case, users or other persons who use the product without

observing the Safety Precautions is responsible for any harm or

damage incurred.

The graphical symbols are explained in detail below.

Once you have fully understood this explanation, read the text.

Improper handling of the product without regard to this

indication will create a hazardous condition that may result in

death or serious injury.

Improper handling of the product without regard to this

indication will create a potentially hazardous condition that

may result in moderate or slight injury or property damage.

WARNING

CAUTION

1 Safety Consideration

The following graphical symbols are used to explain your

responsibilities for using the product safely:

Generally prohibited activity

Disassembly, repair or modiﬁcation prohibited

Mandatory instructions for ordinary users

Graphical symbols for prohibited activity

Graphical symbol for mandatory instructions

1 Safety Consideration

Precautions regarding installation

Do not install the product near electromagnetic sources such as

communication facilities or elevators.

Malfunction of this product may occur in the presence of

electromagnetic interference waves.

Installing or transferring the

product

Precautions for installation

Make sure to place the product on a ﬁrm and ﬂat ﬂoor.

Placing the equipment on a tilted ﬂoor (≥ 5°) may cause it to fall.

To avoid the risk of electric shock, this equipment must only be

connected to a supply mains with protective earth.

Failure or electric leak may result in electric shock.

Precautions for operating the chair

Before and during the chair operation, pay close attention to the

operation range (seat raising/lowering direction, backrest lower-

ing/raising direction), and ensure that the chair does not contact

any body parts,hands or feet, or objects. Body parts, hands or

feet, or objects may become caught in the chair, causing injury

or damage to peripheral devices.



Installing or transferring the

product

Installation

Installation Cautions on Installation Work

Metal or mechanical parts of this product may have sharp edges

or corners. Be careful to avoid injury to your hands and ﬁngers

during installation work.

1-2 Safety Precautions

CONTRAINDICATION

WARNING

CAUTION

2-1 Precautions for installation

1. While carrying the chair, make sure to hold only the

designated parts. If not, it may lead to physical injury.

2. Conﬁrm that the ﬁxing bolts are tightened before carrying the

chair.

3. Take care not to topple the equipment during transportation.

4. Do not drop, hit, or give a shock to the product.

5. Do not connect a power supply other than the rated voltage.

6. Make sure to connect ground wires.

7. When all the installation procedures have been completed,

verify that each function works properly.

2 Cautions regarding installation

3-1 Capacity of power supply equipment to be used

1. The power supply speciﬁcations of the installation site should

be observed. Rated voltage and power supply input for each

CLESTA II CHAIR (EURUS TYPE) are following below.

The minimum capacity of power supply equipment should

have 1,500 VA and over.

3-2 Strength of the building required for installation

1. The ﬂoor strength of the building should be ≥ 4,900 N/m2.

2. As the ﬂoor material of the building, plywood with the thickness

of 25 mm as recommended by Takara Belmont, or a

composite material that combines plywood with the thickness

of 15 mm and particle board with the thickness of 20 mm,

should be used. Alternatively, a ﬂoor material with the strength

greater than the above should be used.

2. Be sure to connect grounding.

3 Conditions for installation site

Rated voltage

Power frquency

Power supply input

AC240V

50Hz

2.2A

AC230V

50Hz

2.0A

AC220V

50/60Hz

1.8A

AC120V

60Hz

3.6A

AC110V

60Hz

3.6A

4 Installation

4-1 Dimensions/Environmental Requirements

4-1-1 Dimensions

Unit: mm (Dimensional tolerance:±10%)

*Dimensions and speciﬁcations are subject

to change without notice.

4-1-2 Environmental Requirements

Usage environment Temperature 0°C to 40°C

Humidity 10% to 95%

Atmospheric pressure 700 to 1060 hPa

Transportation/storage Temperature −20°C to 70°C

environment Humidity 10% to 95%

Atmospheric pressure 700 to 1060 hPa

2010

170

300

210

518

600

1055〜1615

73°

5〜18°

435〜800

1380395

180

170°

235°

4 Installation

4-2 Necessary tools and supplied parts

4-2-1 Necessary tools

The table below shows the necessary tools for the installation of

this product.

Phillips screwdriver No. 1–3

Monkey wrench (Max. opening width: 29 mm)

6-piece double head open end wrench set (5.5–24 mm)

8-piece hex key wrench set (1.5–8 mm)

Level

1 for each

The table below shows the supplied parts included in each unit.

No.

Hex head flange screw TP-A, M8 × 30, black

Hollow set screw, flat end, M10 × 10, SUS

Cap bolt, M6 × 20, black

Cap bolt, M6 × 45, black (only for the specification having right armrest (option))

Spacer, 6 × 30 (only for the specification having right armrest (option))

Spring (only for the specification having right armrest (option))

Flat washer, M6 × 11.5 × 0.8 (only for the specification having right armrest (option))

Clamp

Pump cover

Pump cover lid

Headrest unit

Headrest cover

Backrest cover

Base cover

Base cover lid

Stick switch

Flange cover lid (only for the specification having no right armrest (option))

Truss screw M4×8 white

Part name QTY.

No. Tool name QTY.

Chair [Contour chair type] (unit)

No.

Seat bottom cover (right)

Seat bottom cover (left)

Seat

Backrest

Headrest

Part name QTY.

Chair [Contour chair type] (cover parts)

4-2-2 Supplied parts

1. Unpack the carton of the chair.

Remove wood screws, M4 × 45, plated (10 pieces) for

packing.

2. Remove the chair from the skid.

Remove the hex head ﬂange screw TP-A, M6 × 40 (3 pieces)

that ﬁx the base and skid.

3. Place the chair at the approximate location.

Hold the following positions and lay down the chair.

For no right armrest (option):

Hold the carriage bar and the bottom of the armrest mounting

position on the left side, and hold the carriage bar and carriage

bar 2 on the right side.

For the right armrest (option):

Hold the carriage bar and the bottom of the armrest mounting

position on the right and left sides.

Carriage bar

Carriage bar 2

Carriage bar

Armrest mounting position

Carriage barCarriage bar

Armrest mounting position

4-3 Installation procedures

4-3-1 Installing the chair

4 Installation

Altri manuali per Clesta II

Indice

Altri manuali Belmont Attrezzature odontoiatriche

Belmont

Belmont Clesta Manuale utente

Belmont

Belmont 900 Series Istruzioni operative

Belmont

Belmont BELRAY II 097 Specifiche

Belmont

Belmont CREDIA G1 Manuale utente

Belmont

Belmont CP-ONE PLUS Manuale utente

Belmont

Belmont Phot-X II 303 Manuale utente

Belmont

Belmont BEL-20+ Manuale utente

Belmont

Belmont BELRAY II 097 Manuale utente

Belmont

Belmont Quolis Q5500 Manuale utente

Belmont

Belmont Voyager III Manuale utente

Belmont

Belmont PHOT-X II S 505 Manuale utente

Belmont

Belmont PHOT-XIIS 505 Specifiche

Belmont

Belmont CLESTA eIII Manuale utente

Belmont

Belmont X-Calibur Series Manuale utente

Belmont

Belmont Clesta II Manuale utente

Belmont

Belmont PRO III 047 Manuale utente

Belmont

Belmont CREDIA G1 Manuale utente

Belmont

Belmont Quolis Series Manuale utente

Belmont

Belmont X-Calibur V Manuale utente

Belmont

Belmont tbCompass Manuale utente

Belmont

Belmont CLESTA II CHAIR Manuale utente

Belmont

Belmont CLESTA eIII Manuale utente

Belmont

Belmont Celeb Manuale utente

Belmont

Belmont Quolis Series Manuale utente

Manuali Attrezzature odontoiatriche popolari di altre marche

Vatech

Vatech EzRay Air VEX-P300 Manuale utente

KaVo

KaVo GENTLEpower LUX Contra-angle 25 LP Manuale utente

DENTSPLY

DENTSPLY SmartLite Focus Manuale utente

LM ProPower CombiLED Manuale utente

Owandy Radiology

Owandy Radiology RX-AC Manuale utente

mectron

mectron Piezosurgery Manuale utente

Planmeca

Planmeca Sovereign Classic Manuale utente

Bego

Bego Fornax T Manuale utente

Renfert

Renfert SYMPRO Guida rapida

Ateco

Ateco AT-301 Manuale utente

Nevadent

Nevadent NZPS 3 A1 Manuale utente

Muss Dental

Muss Dental MA 50 Manuale tecnico

Diplomat

Diplomat Comfort Series Manuale utente

Dentatus

Dentatus Nyström Manuale utente

OMS

OMS DUKE EASY Manuale

OMS

OMS LINEA PATAVIUM Manuale

BRYANT DENTAL

BRYANT DENTAL Ignis Gesture A-494322 Manuale utente

Dekema

Dekema AUSTROMAT 664 iSiC Manuale utente