Endress+Hauser Prothermo NMT 539 Manuale utente

Products Solutions Services

BA01026G/08/EN/18.15

71282283

Operating Instructions and

Description of Instrument Function

Prothermo NMT539

Temperature

Prothermo NMT539

2Endress+Hauser

Basic Device Layout of Prothermo NMT539

Figure 1: System Layout 1

1. Average Temperature Prothermo NMT539 Installation on Tank Top

• The actual installation may require an installer to work in a hazardous area. Safety must be taken into account in order to avoid any

harmful conditions.

• The installation method depends on the type of NMT539. Refer to BA01025G/08/EN "Installation Instructions."

2. Wiring to Host Instruments (Tank Side Monitor NRF590 or Proservo NMS5/NMS7)

• Wiring material and conditions must be in accordance with intrinsically safe standards.

• One end (normally on the host instrument side) of the shield twisted pair of cables must be grounded at the terminal connection.

• Refer to BA01025G/08/EN "Installation Instructions."

3. NMT539 Initial Setup

• Both NMT539’s own device setting and local HART setting to the host instrument must be performed.

4. Data Flow from NMT539 to Host Instruments

• Individual element temperature data: Individual raw element temperature can be accessed regardless of liquid level information on

the NMT539’s data matrix.

• Average temperature data: The host instrument sends liquid level data on the local HART line to NMT539. NMT539 calculates both

Gas and Liquid phase average temperature based on this given liquid level.

• WB (Water Bottom) data: WB data and information are continuously scanned and transmitted by host instruments as long as the local

HART connection is active.

Liquid Level

Power (AC/DC)

FMR 540

NRF590

NMT 539

Ex i Local HART Loop

(Data Transmission)

Liquid & Gas

Temperature

Water Interface

(WB)

FMR Power

(DC, Exi)

Fieldbus Protocol

Tankvision

sio

Prothermo NMT539

Endress+Hauser 3

Table of Contents

1 Notes on Safety Conventions and Symbols . . . 4

1.1 Symbols for Certain Types of Information . . . . . . . . . . . 4

2 Initial Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1 Local HART Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Device Setup: NRF590 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Device Setup: NMS5/NMS7 . . . . . . . . . . . . . . . . . . . . . . . 7

3 Operation and Description of Instrument

Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Local HART Device Designation . . . . . . . . . . . . . . . . . . . 9

3.2 Device Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3 Temperature Measurement . . . . . . . . . . . . . . . . . . . . . 10

3.4 Water Bottom Measurement . . . . . . . . . . . . . . . . . . . . 22

3.5 Temperature + Water Bottom Measurement . . . . . . 28

4 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table of Contents

Prothermo NMT539

4Endress+Hauser

1 Notes on Safety Conventions and Symbols

To highlight safety-relevant or alternative operating procedures in this manual, the following conven-

tions have been used, each indicated by a corresponding symbol on the left.

1.1 Symbols for Certain Types of Information

Symbol Meaning

A0011189-EN

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

A0011190-EN

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

A0011192-EN

NOTICE!

This symbol contains information on procedures and other facts which do not result in

personal injury.

Symbol Meaning

A0011182

Allowed

Indicates procedures, processes or actions that are allowed.

A0011183

Recommendation

Indicates procedures, processes or actions that are recommended.

A0011184

Forbidden

Indicates procedures, processes or actions that are forbidden.

A0011193

Tip

Indicates additional information.

DANGER

WARNING

CAUTION

NOTICE

1 Notes on Safety Conventions and Symbols

Prothermo NMT539

Endress+Hauser 5

2 Initial Set Up

2.1 Local HART Connection

2.1.1 Endress+Hauser Tank Gauging Instrument

NMT539 is developed and designated primarily to work with Endress+Hauser tank gauging host

instruments Tank Side Monitor NRF590 or Proservo NMS5/NMS7.

Both temperature and / or water bottom information are transmitted on a two wire i.s local HART loop

to the host instrument. Since both NRF590 and NMS5/NMS7 have a pre-configured menu for NMT

series functionality as default, simple wiring to NMT539 will complete the initial setup for NMT539.

• Refer to the Installation manual BA01025G/08/EN for NMT539 physical installation procedure

prior to start up.

• The availability of each of the four parameters can vary depending on the selected NMT539 mea-

surement function on the product code.

Temperature Measurement Measurement Function

0: Converter only

1: Temperature + converter

These four basic data are available as standard.

1. Average liquid temperature

2. Average gas phase temperature

3. Level (entered liquid level at "VH02 measured distance")

4. Device status

Water Bottom (WB)

Measurement

Measurement Function

2: Water bottom + converter

These four basic data are available as standard.

1. Water bottom level

2. WB probe capacitance

3. WB probe frequency

4. Device status

Temperature + Water

Bottom + Converter

Measurement Function

3: Temperature + water bottom + converter

These four basic data are available as standard.

1. Average liquid temperature

2. Water bottom level

3. Average gas phase temperature

4. Device status

CAUTION

2 Initial Set Up

Prothermo NMT539

6Endress+Hauser

2.2 Device Setup: NRF590

Connect the loop powered local HART communication cable from the NRF590 (intrinsically safe side

compartment) to NMT539 according to BA01025G "Installation Instructions."

Since NRF590 has been designed to recognize NMT539 as a specific Endress+Hauser local HART

instrument, set up is easy.

2.2.1 HART Scanner

After the physical cabling between NMT539 and NRF590 is complete, scan all connected loop powered

local HART devices by activating "HART SCAN" on NRF590.

Not all NRF590 have fully accessible compatibility to recognize the NMT539. Consult with

Endress+Hauser representatives to cross check the software and hardware version of NRF590.

2.2.2 NMT539 Specific Parameter Setup on NRF590

• Configuration of NMT539 parameters on the display of NRF590 is dependent on the installed soft-

ware and hardware version of NRF590. Refer to the operating manual of NRF590 to determine

accessible parameters.

• All required initial setup and configuration can be performed by FieldCare. Detailed information will

be described in the following operation related chapters.

WARNING

NOTICE

2 Initial Set Up

Prothermo NMT539

Endress+Hauser 7

2.3 Device Setup: NMS5/NMS7

NMS5/7 is also specifically designed to recognize NMT539.

Terminals 24 and 25 of NMT539 and NMS5/NMS7 are connected by using local HART.

The connection between NMS5/NMS7 and NMT539 is specified by Ex approval.

Refer to the separate BA01025G "4.4 Terminal Connection" for wiring.

2.3.1 Preparation of NMS5/NMS7

MS5/NMS7 must be pre-configured to accept the NMT539 connection via the multi drop local HART

loop.

GVH362: NMT Connection

"Average Temp." must be selected in order to configure NMT539.

To change this parameter, an access code is required. Refer to BA00401G "NMS5 Operation Instruc-

tions" for further information.

2.3.2 NMT539 Configuration on NMS5/NMS7

Most required NMT539 parameters can be configured on G4 "Temperature" matrix as it is on the dis-

play of NMS5/NMS7.

WB (Water Bottom) sensor information is not available on NMS5/NMS7 before ROM version 4.24.

Consult with Endress+Hauser representatives to update the installed NMS5/NMS7 function.

Typical NMT539 parameters are displayed on the matrix of NMS5/NMS7

G0 Static Matrix GVH010: Liquid Temp

Display average liquid temperature.

GVH013: Gas Temperature

Display gas average temperature.

G4 Dynamic Matrix:

Temperature

GVH440: Liquid Temp

Display the same value indicated on GVH010 Liquid Temp.

GVH441: Gas Temperature

Display the same value indicated on GVH013 Gas Temperature.

GVH442: Measured Level

Display liquid level value established in NMS5/NMS7.

NMT539 must have liquid level data in order to calculate both liquid and gas phase average tempera-

ture.

GVH447: Reference Zero

Check that temperature transforming of measuring temperature resistor is performed correctly.

Allowable range: -1.0 to +1.0°C(+30.2 to +33.8°F)

GVH449: Reference 17

This temperature is used to check at the time of shipping.

GVH450 to 459: Temp No.1 to 10

Display the measuring value of temperature from each inserted element in the probe.

The value of element temperature above 11 to 16 must be selected at GVH470 "Select Point", then the

values are shown at GVH473 "Element Temp."

WARNING

2 Initial Set Up

Prothermo NMT539

8Endress+Hauser

GVH460 to 469: Element Position No.1 to 10

Display each element position in the probe.

Indicating element position above 11 to 16 must be selected at the GVH470 "Select Point", then the

positions are shown at GVH474 "Element Position"

GVH470: Select Point

Select matrix of GVH471 "Zero Adjust", GVH473 "Element Temp", and GVH474 "Element Position." and

input the desired element data.

GVH480: Diagnostic

Display of error code message. Refer to the error code chart in a later chapter of this manual.

GVH482: Total No. Element

Input the number of installed temperature elements in the average temperature probe.

GVH485: Type of Interval

Select type of element interval.

Even: Element spacing will be equally spaced by providing the distance at GVH487 "Element Interval",

and the lowest element position can be set at GVH486 "Bottom Point."

Not Even: Element spacing will be unequally distributed. As a result, each element position must be

manually entered.

This parameter setting is only used to change the theoretical element position within NMT539’s

software for average calculation purposes. The physical location of the temperature element position

does not change.

GVH486: Bottom Point

The lowest inserted element position in the average temperature probe.

This parameter setting is only used to change the theoretical element position within NMT539’s

software for average calculation purposes. The physical location of the temperature element position

does not change.

GVH487: Element Interval

Enter the desired element interval when "Even" in GVH485 " Type of Interval" is selected.

This parameter setting is only used to change the theoretical element position within NMT539’s

software for average calculation purposes. The physical location of the temperature element position

does not change.

NOTICE

2 Initial Set Up

Prothermo NMT539

Endress+Hauser 9

3 Operation and Description of Instrument

Function

This section is described for description for FieldCare.

NMT539 has segmented local HART device code depending on measurement function. Following 4

local HART device codes are normally pre-set at the factory by jumper setting.

Do not change jumper setting by disassembling NMT539’s internal module. It may cause major mal-

function due to distorted precise factory calibration.

3.1 Local HART Device Designation

Local HART device code "184":

This code is the device code for temperature measurement function only. This 184 is specifically

designed for NMT539 converter only version and converter + temperature version. No WB sensor is

available with code 184.

Local HART device code "185":

This code is the device code for equipped NMT539 water I/F measurement function. FieldCare does

not recognize code 185.

Local HART device code "186":

This code is the device code for fully equipped NMT539. NMT539 with converter + temperature +

water bottom uses code 186.

3.2 Device Data

Tag Number: read and write

Default: local HART

This number is for A customer specific device identification and control number (or name). Tank name,

site number, or any other ID can be entered.

Assembly Number: read and write

Default: 0

This number is for manufacture control number based on production process.

WARNING

3 Operation and Description of Instrument Function

Prothermo NMT539

10 Endress+Hauser

3.3 Temperature Measurement

These 2 local HART device codes 184 is designated to perform only temperature measurement func-

tion. Available parameter and function are follows. Description of these parameters are the informa-

tion based on FieldCare menu.

Local HART device code will be only displayed when default header position or VH99 "Device Type Code"

on FieldCare menu are available.

Designated temperature measurement function device is available on following product order code.

Measuring Function

0: Converter Only

1: Converter + temperature

4: Converter + temperature (W&M certification)

3.3.1 Primary Values: VH00 to VH09

VH00: Liquid Temp

Item type: read only

Range: -200°C to 240°C

• Display measured liquid phase average temperature.

• Liquid level input must be provided by Micropilot radar level gauge (via NRF590) or NMS5/NMS7

series servo level gauge in order to calculate true liquid average temperature.

VH01: Gas Temp

Item type: read only

Range: -200°C to 240°C

Display measured gas (vapor) phase average temperature.

Liquid level input must be provided by Micropilot radar level gauge (via NRF590) or NMS5/NMS7

servo level gauge in order to calculate true gas average temperature.

VH02: Measured Distance

Item type: read and write

Range: 0mm to 99999mm

Display provided liquid level by connected level gauge.

When level gauge is not connected, inputting liquid level is also available for the device test purpose.

VH07: Temperature 0

Item type: read only

Check that temperature transforming of measuring temperature resistor is performed correctly.

Allowable range: -1.0 to +1.0 °C(+30.2 to + 33.8°F)

VH09: Temperature 17

Item type: read only

This temperature is used to check at the time of shipping.

NOTICE

3 Operation and Description of Instrument Function

Altri manuali per Prothermo NMT 539

Indice

Altri manuali Endress+Hauser Attrezzature industriali

Endress+Hauser

Endress+Hauser SpectraSensors OXY5500 Guida all'installazione

Endress+Hauser

Endress+Hauser ASP Station 2000 RPS20B Manuale utente

Endress+Hauser

Endress+Hauser Micropilot FMR50 Aggiornamento firmware

Endress+Hauser

Endress+Hauser Tankvision Multi Scan NXA83 Manuale utente

Endress+Hauser

Endress+Hauser Kit CSF48 Manuale utente

Endress+Hauser

Endress+Hauser TopCal S CPC 300 Manuale utente

Endress+Hauser

Endress+Hauser Liquiline System CA80PH Specifiche tecniche

Endress+Hauser

Endress+Hauser Proline t-mass 65 Manuale utente

Endress+Hauser

Endress+Hauser Flexdip CYA112 Manuale utente

Endress+Hauser

Endress+Hauser Teqwave F/I Specifiche tecniche

Endress+Hauser

Endress+Hauser 51517656 CleanFit H CPA 475 Manuale utente

Endress+Hauser

Endress+Hauser Stamoclean CAT430 Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA871 Manuale utente

Endress+Hauser

Endress+Hauser SmarTec S CLD 132 PROFIBUS-PA Manuale utente

Endress+Hauser

Endress+Hauser Soliwave FQR56 Manuale utente

Endress+Hauser

Endress+Hauser Liquistation CSF39 Specifiche tecniche

Endress+Hauser

Endress+Hauser Cleanfit P CPA471 Manuale utente

Endress+Hauser

Endress+Hauser Soliwave FDR16 Manuale utente

Endress+Hauser

Endress+Hauser HART Proline Promass 500 Manuale dell'operatore

Endress+Hauser

Endress+Hauser Proservo NMS83 Manuale utente

Endress+Hauser

Endress+Hauser T13 Manuale

Endress+Hauser

Endress+Hauser Stamoclean CAT430 Manuale utente

Endress+Hauser

Endress+Hauser Fieldgate FXA720 Manuale utente

Endress+Hauser

Endress+Hauser Micropilot FMR67 Aggiornamento firmware

Manuali Attrezzature industriali popolari di altre marche

ABB

ABB Unifix AD Manuale

Mark 7

Mark 7 Evolution Manuale utente

Husky

Husky HyPET Manuale utente

bora

bora PM-1800 Manuale utente

Grizzly

Grizzly T32428 Manuale utente

Siemens

Siemens 8MF1 Series Manuale utente

ABB

ABB HT610965 Manuale utente

ABB

ABB SafeLink Manuale utente

Phoenix

Phoenix PHX-150 Manuale utente

ABB

ABB A165-L32 Manuale utente

ABB

ABB HT842936 Manuale utente

Rioned

Rioned UrbanJet Manuale utente

Hermetica

Hermetica 10 Series Manuale utente

HORNER

HORNER OEE Solution Manuale utente

Hammerhead

Hammerhead HG375 Manuale utente

SCHUNK

SCHUNK VERO-S NSE-A3 138 Istruzioni utente

ABB

ABB HT566657 Manuale utente

Webasto

Webasto GSE CAN Manuale utente