Epson S5U13700P00C000 Manuale utente

Revision 1.1

S1D13706 Embedded Memory LCD Controller

S5U13706P00C100 Evaluation Board

User Manual

Document Number: X31B-G-021-01

Status: Revision 1.1

Issue Date: 2009/03/03

Information in this document is subject to change without notice. You may download and use this document, but only for your own use in

evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any

representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain

material protected under U.S. and/or International Patent laws.

EPSON is a registered trademark of Seiko Epson Corporation. All other Trademarks are the property of their respective owners

Page 2 Epson Research and Development

Vancouver Design Center

S1D13706 S5U13706P00C100 Evaluation Board User Manual

X31B-G-021-01 Issue Date: 2009/03/03

Revision 1.1

Epson Research and Development Page 3

Vancouver Design Center

S5U13706P00C100 Evaluation Board User Manual S1D13706

Issue Date: 2009/03/03 X31B-G-021-01

Revision 1.1

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Configuration DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.2 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

4 CPU Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.1 CPU Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.2 CPU Bus Connector Pin Mapping . . . . . . . . . . . . . . . . . . . . . . 12

5 LCD Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

6.1 PCI Bus Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

6.2 Direct Host Bus Interface Support . . . . . . . . . . . . . . . . . . . . . . 16

6.3 S1D13706 Embedded Memory . . . . . . . . . . . . . . . . . . . . . . . . 16

6.4 Software Adjustable LCD Backlight Intensity Support Using PWM . . . . . . . . . 16

6.5 Passive/Active LCD Panel Support . . . . . . . . . . . . . . . . . . . . . . 17

6.5.1 Buffered LCD Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6.5.2 Extended LCD Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6.6 External oscillator support for CLKI and CLKI2 . . . . . . . . . . . . . . . . . 17

7 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

7.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

7.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

8 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

9 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

10 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

11 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

11.1 EPSON LCD Controllers (S1D13706) . . . . . . . . . . . . . . . . . . . . . 28

Page 4 Epson Research and Development

Vancouver Design Center

S1D13706 S5U13706P00C100 Evaluation Board User Manual

X31B-G-021-01 Issue Date: 2009/03/03

Revision 1.1

Epson Research and Development Page 5

Vancouver Design Center

S5U13706P00C100 Evaluation Board User Manual S1D13706

Issue Date: 2009/03/03 X31B-G-021-01

Revision 1.1

1 Introduction

This manual describes the setup and operation of the S5U13706P00C100 Evaluation

Board. The board is designed as an evaluation platform for the S1D13706 Embedded

Memory LCD Controller.

This user manual is updated as appropriate. Please check the Epson Research and Devel-

opment website at www.erd.epson.com for the latest revision of this document before

beginning any development.

We appreciate your comments on our documentation. Please contact us via email at

documentati[email protected].

Page 6 Epson Research and Development

Vancouver Design Center

S1D13706 S5U13706P00C100 Evaluation Board User Manual

X31B-G-021-01 Issue Date: 2009/03/03

Revision 1.1

2 Features

Following are some features of the S5U13706P00C100 Evaluation Board:

• 100-pin TQFP S1D13706F00A Embedded Memory LCD Controller with 80K bytes of

embedded SRAM.

• Headers for connecting to various Host Bus Interfaces.

• Configuration options.

• Software adjustable backlight intensity support.

• 4/8-bit 3.3V or 5V single monochrome passive LCD panel support.

• 4/8/16-bit 3.3V or 5V single color passive LCD panel support.

• 9/12/18-bit 3.3V or 5V active matrix TFT LCD panel support.

• Direct interface for 18-bit Epson D-TFD LCD panel support.

• Direct interface for 18-bit Sharp HR-TFT LCD panel support.

• Software initiated power save mode.

• Hardware or software Video Invert support.

• External oscillator for CLKI and CLKI2.

Epson Research and Development Page 7

Vancouver Design Center

S5U13706P00C100 Evaluation Board User Manual S1D13706

Issue Date: 2009/03/03 X31B-G-021-01

Revision 1.1

3 Installation and Configuration

The S5U13706P00C100 is designed to support as many platforms as possible. The

S5U13706P00C100 incorporates a DIP switch and three jumpers which allow both the

evaluation board and S1D13706 LCD controller to be configured for a specified evaluation

platform.

3.1 Configuration DIP Switches

The S1D13706 has configuration inputs (CNF[7:0]) which are read on the rising edge of

RESET#. In order to configure the S1D13706 for multiple Host Bus Interfaces a ten-

position DIP switch (S1) is provided. The following figure shows the location of DIP

switch SW1 on the S5U13706P00C100.

Figure 3-1: Configuration DIP Switch (SW1) Location

DIP Switch - SW1

Page 8 Epson Research and Development

Vancouver Design Center

S1D13706 S5U13706P00C100 Evaluation Board User Manual

X31B-G-021-01 Issue Date: 2009/03/03

Revision 1.1

The S1D13706 has 8 configuration inputs (CNF[7:0]) which are read on the rising edge of

RESET#. All S1D13706 configuration inputs are fully configurable using a ten position

DIP switch as described below.

Note

1To enable the Hardware Video Invert function the following are required:

• GPIO pins must be enabled (S1-4 closed).

• GPIO0 must be connected to S1-9 (Jumper JP1 set to 1-2).

• GPIO Pin Input Enable (REG[A9h] bit 7) must be set to 1b.

• GPIO0 Pin IO Configuration (REG[A8h] bit 0) must be set to 0b.

• Hardware Video Invert Enable bit (REG[70h] bit 5) must be set to 1b.

Table 3-1: Configuration DIP Switch Settings

Switch S1D13706

Signal Value on this pin at rising edge of RESET# is used to configure:

Closed (On/1) Open (Off/0)

SW1-[3:1] CNF[2:0]

Select host bus interface as follows:

CNF2 CNF1 CNF0 Host Bus Interface

000 SH-4/SH-3

0 0 1 MC68K #1

0 1 0 MC68K #2

0 1 1 Generic #1

1 0 0 Generic #2

101 RedCap2

1 1 0 DragonBall

111 Reserved

Note: The host bus interface is 16-bit.

SW1-4 CNF3 Enable GPIO pins Enable additional pins for D-TFD/HR-TFT

SW1-5 CNF4 Big Endian bus interface Little Endian bus interface

SW1-6 CNF5 WAIT# is active high WAIT# is active low

SW1-[8:7] CNF[7:6]

CLKI to BClk divide select:

CNF7 CNF6 CLKI to BClk Divide Ratio

00 1:1

01 2:1

10 3:1

11 4:1

SW1-91- Hardware Video Invert - invert video data1Hardware Video Invert - normal video data1

SW1-10 - Disable FPGA for non-PCI host Enable FPGA for PCI host

= Required settings when used with PCI Bridge FPGA

Epson Research and Development Page 9

Vancouver Design Center

S5U13706P00C100 Evaluation Board User Manual S1D13706

Issue Date: 2009/03/03 X31B-G-021-01

Revision 1.1

3.2 Configuration Jumpers

The S5U13706P00C100 has seven jumper blocks which configure various setting on the

evaluation board. The jumper positions for each function are shown below.

JP1 - GPIO0 Connection

JP1selectswhetherGPIO0isconnected toSW1-9.SW1-9isusedto enablehardwarevideo

invert on the S1D13706.

When the jumper is on (position 1-2), SW1-9 controls the hardware video invert feature

(default setting).

When the jumper is off, the hardware video invert feature is disabled. This setting must be

used for HR-TFT and D-TFD panels as GPIO0 is required for both panels. For details, refer

to the S1D13706 Hardware Functional Specification, document number X31B-A-001-xx.

Note

When configured for Sharp HR-TFT or Epson D-TFD panels, JP1 must be set to no

jumper and JP6 must be set to position 2-3.

Figure 3-2: Configuration Jumper (JP1) Location

Table 3-2: Jumper Summary

Jumper Function Position 1-2 Position 2-3 No Jumper

JP1 GPIO0 Connection GPIO0 connected to

SW1-9 for hardware video

invert —

GPIO0 disconnected from

SW1-9 for direct

HR-TFT/D-TFD or GPIO

testing

JP4 GP0 Polarity on H1 Normal (Active High) Inverted (Active Low) —

JP6 LCD Panel Voltage +5V LCDVCC +3.3V LCDVCC —

= recommended settings

JP1

GPIO0 connected GPIO0 disconnected

to SW1-9 from SW1-9

Page 10 Epson Research and Development

Vancouver Design Center

S1D13706 S5U13706P00C100 Evaluation Board User Manual

X31B-G-021-01 Issue Date: 2009/03/03

Revision 1.1

JP4 - GPO Polarity on H1

JP4 selects the polarity of the GPO signal available on LCD Connector H1.

Position 1-2 sends the GPO signal directly to H1 (default setting).

Position 2-3 inverts the GPO signal before sending it to H1.

Figure 3-3: Configuration Jumper (JP4) Location

JP6 - LCD Panel Voltage

JP6 selects the voltage level to the LCD panel.

Position 1-2 sets the voltage level to 5.0V.

Position 2-3 sets the voltage level to 3.3V (default setting).

Note

When configured for Sharp HR-TFT or Epson D-TFD panels, JP1 must be set to no

jumper and JP6 must be set to position 2-3.

Figure 3-4: Configuration Jumper (JP6) Location

JP4

Inverted

Normal

JP6

5.0V 3.3V

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Epson Scheda madre

Epson

Epson S5U13517P00C100 Manuale utente

Epson

Epson S5U13706B00C Manuale utente

Epson

Epson S5U13A04B00C Manuale utente

Epson

Epson S1R72U16 Manuale utente

Epson

Epson S5U1C17965T2 Manuale utente

Epson

Epson S1D13513 Manuale utente

Epson

Epson S1R72U06 Manuale utente

Epson

Epson S1V30000 Series Guida utente

Epson

Epson S5U1C17602T1100 Istruzioni per il montaggio

Epson

Epson S5U13A05B00C Manuale utente

Epson

Epson S1V30080F00A300 Manuale utente

Epson

Epson S5U13C00P00CX00 Manuale utente

Epson

Epson S5U13513P00C100 Manuale utente

Epson

Epson S5U13L03P00C100 Manuale utente

Epson

Epson Buzzer S1C31D51 Manuale utente

Epson

Epson S5U13A04B00C Manuale utente

Epson

Epson SG-WRITERII Istruzioni per l’uso

Epson

Epson S5U13L01P00C100 Manuale utente

Epson

Epson S5U13T04P00C100 Manuale utente

Epson

Epson S5U13706P00C100 Manuale utente

Epson

Epson S5U1C6S3N2E2 Manuale utente

Epson

Epson S5U13700B00C Manuale utente

Epson

Epson S5U13781R00C100 Manuale utente

Epson

Epson S1R72V27 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente