Toshiba RAS-05, RAS-07 Manuale utente

AIR CONDITIONER (SPLIT TYPE)

INSTALLATION MANUAL

1118350197

Indoor unit

RAS-05, 07, 10, 13, 16BKV-E

Outdoor unit

RAS-05, 07, 10, 13, 16BAV-E

ENGLISH

PRECAUTIONS FOR SAFETY...........................................................................................................................................1

ACCESSORY PARTS .........................................................................................................................................................2

INSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITS ...................................................................................3

Optional Installation Parts ...............................................................................................................................................3

INDOOR UNIT.....................................................................................................................................................................4

Installation Place.............................................................................................................................................................4

Cutting a Hole and Mounting Installation Plate ...............................................................................................................4

Piping and Drain Hose Installation..................................................................................................................................4

Indoor Unit Fixing............................................................................................................................................................5

Drainage .........................................................................................................................................................................5

OUTDOOR UNIT.................................................................................................................................................................6

Installation Place.............................................................................................................................................................6

Precautions about Installation in Regions with Snowfall and Cold Temperatures ..........................................................6

Refrigerant Piping Connection ........................................................................................................................................6

Evacuating .....................................................................................................................................................................7

ELECTRICAL WORKS .......................................................................................................................................................8

Wiring Connection...........................................................................................................................................................8

Power Supply and Connecting Cable Connection ..........................................................................................................9

Power Supply Input Wiring Diagram .............................................................................................................................10

OTHERS............................................................................................................................................................................ 11

Gas Leak Test ............................................................................................................................................................... 11

Remote Control A-B Selection ...................................................................................................................................... 11

Test Operation .............................................................................................................................................................. 11

Auto Restart Setting ..................................................................................................................................................... 11

APPENDIX ........................................................................................................................................................................12

CONTENTS

PRECAUTIONS FOR SAFETY

WARNING

• Never modify this unit by removing any of the safety guards or bypassing any of the safety interlock switches.

• Do not install in a place which cannot bear the weight of the unit.

Personal injury and property damage can result if the unit falls.

• Before doing the electrical work, attach an approved plug to the power supply cord.

Also, make sure the equipment is properly earthed.

• Appliance shall be installed in accordance with national wiring regulations.

If you detect any damage, do not install the unit. Contact your dealer immediately.

• Do not use any refrigerant different from the one speciﬁed for complement or replacement.

Otherwise, abnormally high pressure may be generated in the refrigeration cycle, which may result in a failure or explosion of the product or an injury to your

body.

DANGER

• FOR USE BY QUALIFIED PERSONS ONLY.

• TURN OFF MAIN POWER SUPPLY BEFORE ATTEMPTING ANY ELECTRICAL WORK. MAKE SURE ALL POWER SWITCHES ARE OFF.

FAILURE TO DO SO MAY CAUSE ELECTRIC SHOCK.

• CONNECT THE CONNECTING CABLE CORRECTLY. IF THE CONNECTING CABLE IS CONNECTED WRONGLY, ELECTRIC PARTS MAY BE

DAMAGED.

• CHECK THE EARTH WIRE THAT IT IS NOT BROKEN OR DISCONNECTED BEFORE INSTALLATION.

• DO NOT INSTALL NEAR CONCENTRATIONS OF COMBUSTIBLE GAS OR GAS VAPORS.

FAILURE TO FOLLOW THIS INSTRUCTION CAN RESULT IN FIRE OR EXPLOSION.

• TO PREVENT OVERHEATING THE INDOOR UNIT AND CAUSING A FIRE HAZARD, PLACE THE UNIT WELL AWAY (MORE THAN 2 M) FROM

HEAT SOURCES SUCH AS RADIATORS, HEATERS, FURNACE, STOVES, ETC.

• WHEN MOVING THE AIR CONDITIONER FOR INSTALLING IT IN ANOTHER PLACE AGAIN, BE VERY CAREFUL NOT TO GET THE SPECIFIED

REFRIGERANT (R410A) WITH ANY OTHER GASEOUS BODY INTO THE REFRIGERATION CYCLE. IF AIR OR ANY OTHER GAS IS MIXED IN THE

REFRIGERANT, THE GAS PRESSURE IN THE REFRIGERATION CYCLE BECOMES ABNORMALLY HIGH AND IT RESULTINGLY CAUSES BURST

OF THE PIPE AND INJURIES ON PERSONS.

• IN THE EVENT THAT THE REFRIGERANT GAS LEAKS OUT OF THE PIPE DURING THE INSTALLATION WORK, IMMEDIATELY LET FRESH AIR

INTO THE ROOM. IF THE REFRIGERANT GAS IS HEATED BY FIRE OR SOMETHING ELSE, IT CAUSES GENERATION OF POISONOUS GAS.

CAUTION

• Exposure of unit to water or other moisture before installation could result in electric shock.

Do not store it in a wet basement or expose to rain or water.

• After unpacking the unit, examine it carefully for possible damage.

• Do not install in a place that can increase the vibration of the unit. Do not install in a place that can amplify the noise level of the unit or where noise and

discharged air might disturb neighbors.

• To avoid personal injury, be careful when handling parts with sharp edges.

• Please read this installation manual carefully before installing the unit. It contains further important instructions for proper installation.

• The manufacturer shall not assume any liability for the damage caused by not observing the description of this manual.

• Before installation, please read these precautions for safety carefully.

• Be sure to follow the precautions provided here to avoid safety risks. The symbols and their meanings are shown below.

WARNING : It indicates that incorrect use of this unit may cause severe injury or death.

CAUTION : It indicates that incorrect use of this unit may cause personal injury (*1), or property damage (*2).

*1: Personal injury means a slight accident, burn, or electrical shock which does not require admission or repeated hospital treatment.

*2: Property damage means greater damage which affects assets or resources.

For general public use

Power supply cord and connecting cable of appliance use shall be at least polychloroprene sheathed ﬂexible cord (design H07RN-F) or cord designation

60245 IEC66. (Shall be installed in accordance with national wiring regulations.)

This appliance must be connected to the main power supply by means of a circuit breaker or a switch with a contact separation of at least 3 mm in all poles.

CAUTION To disconnect the appliance from the main power supply

New refrigerant air conditioner installation

CAUTION

• THIS AIR CONDITIONER USES THE NEW HFC REFRIGERANT (R410A), WHICH DOES NOT DESTROY THE OZONE LAYER.

R410A refrigerant is apt to be affected by impurities such as water, oxidizing membranes, and oils because the pressure of R410A refrigerant is approx.

1.6 times of refrigerant R22. As well as the adoption of this new refrigerant, refrigerating machine oil has also been changed. Therefore, during installation

work, be sure that water, dust, former refrigerant, or refrigerating machine oil does not enter the refrigeration cycle of a new-refrigerant air conditioner.

To avoid mixing refrigerant and refrigerating machine oil, the sizes of charging port connecting sections on the main unit are different from those for the

conventional refrigerant, and different size tools are also required. For connecting pipes, use new and clean piping materials with high pressure withstand

capabilities, designed for R410A only, and ensure that water or dust does not enter. Moreover, do not use any existing piping as its pressure withstand

may be insufﬁcient and may contain impurities.

REQUIREMENT OF REPORT TO THE LOCAL POWER SUPPLIER

Please make absolutely sure that the installation of this appliance is reported to the local power supplier before installation. If you experience any problems

or if the installation is not accepted by the supplier, the service agency will take adequate countermeasures.

ACCESSORY PARTS

Indoor Unit

No. Part name No. Part name

Installation Plate × 1

Wireless remote control × 1

3Battery × 2 4

Remote control holder × 1

5Mounting screw × 6 6Flat head wood screw × 2

Owner’s Manual × 1

Installation Manual × 1

Outdoor Unit

No. Part name No. Part name

Drain nipple × 1

Cap water proof × 2*

* Not require to use for RAS-05, 07, 10, 13BAV-E

Air ﬁlters

Clean every 2 weeks.

1. Open the air inlet grille.

2. Remove the air ﬁlters.

3. Vacuum or wash and then dry them.

4. Reinstall the air ﬁlters and close the air inlet grille.

INSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITS

Part

code Parts name Q’ty

Refrigerant piping

Liquid side : Ø6.35 mm

Gas side : Ø9.52 mm

(RAS-05, 07, 10, 13BKV-E)

Ø12.70 mm

(RAS-16BKV-E)

One

each

BPipe insulating material

(polyethylene foam, 6 mm thick) 1

CPutty, PVC tapes One

each

Optional Installation Parts

• Secure the outdoor unit with ﬁxing bolts and nuts if the unit is likely to be

exposed to a strong wind.

• Use Ø8 mm or Ø10 mm anchor bolts and nuts.

• If it is necessary to drain the defrost water, attach drain nipple 9and cap

waterproof !to the bottom plate of the outdoor unit before installing it.

Fixing bolt arrangement of outdoor unit

Insulate the refrigerant pipes separately

with insulation, not together.

Insert the cushion between the indoor

unit and wall, and tilt the indoor unit for

better operation.

For the rear left and left piping

Wall

Make sure to run the drain hose sloped

downward.

Do not allow the drain hose to get slack.

Cut the piping

hole sloped

slightly.

The auxiliary piping can be connected to

the left, rear left, rear right, right, bottom

right or bottom left.

Right

Rear

right

Bottom

right

Rear

left Bottom left

Left

6 mm thick heat resisting

polyethylene foam

Batteries

Flat head

wood screw Remote control holder

Vinyl tape

Apply after carrying

out a drainage test.

Wireless remote control

Saddle

Extension drain hose

(Not available, provided

by installer)

Shield pipe

(Attach to the front panel.)

Air ﬁlter

Hook

Installation

plate

Hook

65 mm or more

300 mm or more

C mm or more

F mm or more

E mm or more

D mm or more

C mm or more

RAS-05, 07, 10, 13BAV-E RAS-16BAV-E

C600 600

D 400 600

E 45 100

F 100 100



Drain outlet

Air inlet

Air outlet

108 mm

28 mm

600 mm

320 mm

125 mm

86 mm

102 mm

90 mm

Ø25 mm

Drain outlet

Air inlet

Air outlet

280 mm

500 mm

53 mm

97 mm

Ø25 mm

RAS-05, 07, 10, 13BAV-E RAS-16BAV-E

INDOOR UNIT

Installation Place

• Direct sunlight to the indoor unit’s wireless receiver should be avoided.

• The microprocessor in the indoor unit should not be too close to RF

noise sources.

(For details, see the owner’s manual.)

Remote control

• A place where there are no obstacles such as a curtain that may block the

signal from the indoor unit

• Do not install the remote control in a place exposed to direct sunlight or

close to a heating source such as a stove.

• Keep the remote control at least 1 m apart from the nearest TV set or

stereo equipment. (This is necessary to prevent image disturbances or

noise interference.)

• The location of the remote control should be determined as shown below.

Cutting a Hole and Mounting

Installation Plate

NOTE

• When drilling a wall that contains a metal lath, wire lath or metal plate, be sure

to use a pipe hole brim ring sold separately.

Cutting a hole

When installing the refrigerant pipes from the rear

Mounting the installation plate

When the installation plate is directly mounted

on the wall

1. Securely ﬁt the installation plate onto the wall by screwing it in the upper and

lower parts to hook up the indoor unit.

2. To mount the installation plate on a concrete wall with anchor bolts, use the

anchor bolt holes as illustrated in the below ﬁgure.

3. Install the installation plate horizontally in the wall.

When installing the installation plate with a mounting screw, do not use the

anchor bolt holes. Otherwise, the unit may fall down and result in personal

injury and property damage.

1. After determining the pipe hole position on the mounting plate (Æ), drill

the pipe hole (Ø65 mm) at a slight downward slant to the outdoor side.

• A place which provides the spaces around the indoor unit as shown in the

diagram

• A place where there are no obstacles near the air inlet and outlet

• A place which allows easy installation of the piping to the outdoor unit

• A place which allows the front panel to be opened

• The indoor unit shall be installed at least 2.5 m height. Also, it must be

avoided to put anything on the top of the indoor unit.

CAUTION

54 °

45°

7°

(Side view) (Top view)

Indoor unit

Reception range

Remote

control

Remote

control

Reception

range

Indoor unit

CAUTION

Failure to ﬁrmly install the unit may result in personal injury and property

damage if the unit falls.

• In case of block, brick, concrete or similar type walls, make 5 mm dia. holes

in the wall.

• Insert clip anchors for appropriate mounting screws 5.

NOTE

• Secure four corners and lower parts of the installation plate with 4 to 6

mounting screws to install it.

CAUTION

The center of the pipe hole

is above the arrow.

Pipe hole

Ø65 mm

120 mm

Installation plate

(Keep horizontal direction.)

5 mm dia. hole

Clip anchor

(local parts)

Mounting screw

Ø4 x 25R

Anchor bolt

Projection

15 mm or less

144

50 50

300

65 103

300

Hook

Hook Hook

Pipe hole

Installation

plate

Mounting screw

Weight

Indoor unit Thread

Piping and Drain Hose Installation

* Since dewing results in a machine trouble, make sure to insulate both

connecting pipes. (Use polyethylene foam as insulating material.)

Piping and drain hose forming

1. Die-cutting back body slit

Cut out the slit on the left or right side of the back body for the left or right

connection and the slit on the bottom left or right side of the back body

for the bottom left or right connection with a pair of nippers.

Rear right

Rear left

Bottom left

Left

Bottom right

Right

Die-cutting

back body slit

Changing

drain hose

Piping preparation

2. Changing drain hose

For leftward connection, bottom-leftward connection and rearleftward

connection’s piping, it is necessary to change the drain hose and drain

cap.

4 mm

How to remove the drain cap

Clip the drain cap by needle-nose

pliers and pull out.

How to remove the drain hose

• The drain hose can be removed by removing the

screw securing the drain hose and then pulling out

the drain hose.

• When removing the drain hose, be careful of any

sharp edges of steel plate. The edges can injuries.

• To install the drain hose, insert the drain hose

ﬁrmly until the connection part contacts with heat

insulator, and then secure it with original screw.

How to ﬁx the drain cap

1) Insert hexagon wrench (4 mm)

in a center head.

2) Firmly insert the drain cap.

Firmly insert the drain hose and drain cap; otherwise, water may leak.

CAUTION

Do not apply lubricating oil

(refrigerant machine oil) when

inserting the drain cap. Application

causes deterioration and drain

leakage of the plug.

Insert a hexagon

wrench (4 mm).

No gap

Drain hose

Left-hand connection with piping

• Bend the connecting pipe so that it is laid within 43 mm above the wall

surface. If the connecting pipe is laid exceeding 43 mm above the wall

surface, the indoor unit may unstably be set on the wall.

When bending the connecting pipe, make sure to use a spring bender so

as not to crush the pipe.

Bend the connecting pipe within a radius of 30 mm.

To connect the pipe after installation of the unit (ﬁgure)

270 mm

230 mm

43 mm

Liquid side

Gas side

(To the forefront of ﬂare)

Outward form of indoor unit

R 30 mm (Use polisin (polyethylene)

core or the like for bending pipe.)

Use the handle of screwdriver, etc.

NOTE

If the pipe is bent incorrectly, the indoor unit may unstably be set on the wall.

After passing the connecting pipe through the pipe hole, connect the

connecting pipes to the auxiliary pipes and wrap the facing tape around

them.

In case of right or left piping

• After scribing slits of the back body

with a knife or a making-off pin, cut

them with a pair of nippers or an

equivalent tool.

In case of bottom right or bottom left piping

• After scribing slits of the back body

with a knife or a making-off pin, cut

them with a pair of nippers or an

equivalent tool.

Slit

CAUTION

• Bind the auxiliary pipes (two) and connecting cable with facing tape

tightly. In case of leftward piping and rear-leftward piping, bind the

auxiliary pipes (two) only with facing tape.

Indoor unit

Connecting cable

Auxiliary pipes

Installation plate

• Carefully arrange pipes so that any pipe does not stick out of the rear

plate of the indoor unit.

• Carefully connect the auxiliary pipes and connecting pipes to one

another and cut off the insulating tape wound on the connecting pipe to

avoid double-taping at the joint; moreover, seal the joint with the vinyl

tape, etc.

• Since dewing results in a machine trouble, make sure to insulate both

connecting pipes. (Use polyethylene foam as insulating material.)

• When bending a pipe, carefully do it, not to crush it.

Do not form the

drain hose into

a wavy shape.

Do not rise the

drain hose.

50 mm

or more

Do not put the

drain hose end

into water.

Do not put the

drain hose end

in the drainage ditch.

Hook here.

Installation plate

Hook Press

(unhook)

Push Push

Indoor Unit Fixing

• For detaching the indoor unit from

the installation plate, pull the indoor

unit toward you while pushing its

bottom up at the speciﬁed parts.

1. Pass the pipe through the hole in the wall and hook the indoor unit on the

installation plate at the upper hook.

2. Swing the indoor unit to right and left to conﬁrm that it is ﬁrmly hooked up on

the installation plate.

3. While pressing the indoor unit onto the wall, hook it at the lower part on the

installation plate. Pull the indoor unit toward you to conﬁrm that it is ﬁrmly

hooked up on the installation plate.

Drainage

1. Run the drain hose sloped downwards.

NOTE

• The hole should be made at a slight downward slant on the outdoor side.

Drain

guide

Space for pipes

Wall

Shield pipe

Inside the room

Drain hose Extension drain hose

Arrange the drain pipe for proper drainage from the unit.

Improper drainage can result in dew-dropping.

This air conditioner has the structure designed

to drain water collected from dew, which forms

on the back of the indoor unit, to the drain pan.

Therefore, do not store the power cord and other

parts at a height above the drain guide.

CAUTION

OUTDOOR UNIT

Installation Place

• A place which provides the spaces around the outdoor unit as shown in the

diagram

• A place which can bear the weight of the outdoor unit and does not allow an

increase in noise level and vibration

• A place where the operation noise and discharged air do not disturb your

neighbors

• A place which is not exposed to a strong wind

• A place free of a leakage of combustible gases

• A place which does not block a passage

• When the outdoor unit is to be installed in an elevated position, be sure to

secure its feet.

• The allowable pipe length is up to 15 m for RAS-05, 07, 10, 13BAV-E and

20 m for RAS-16BAV-E.

• The allowable height of outdoor-unit installation site is up to 12 m.

• A place where the drain water does not raise any problems

CAUTION

1. Install the outdoor unit without anything blocking the air discharging.

2. When the outdoor unit is installed in a place always exposed to strong

wind like a coast or on a high storey of a building, secure the normal fan

operation using a duct or a windshield.

3. In particularly windy areas, install the unit such as to avoid admission of

wind.

4. Installation in the following places may result in trouble.

Do not install the unit in such places.

• A place full of machine oil

• A saline-place such as the coast

• A place full of sulﬁde gas

• A place where high-frequency

waves are likely to be generated

as from audio equipment, welders,

and medical equipment

Strong

wind

• Do not use the supplied drain nipple for draining water. Drain the water

from all the drain holes directly.

• To protect the outdoor unit from snow accumulation, install a holding

frame, and attach a snow protection hood and plate.

* Do not use a double-stacked design.

Precautions about Installation in Regions

with Snowfall and Cold Temperatures

Snow protection plate

Snow protection hood

Snow accumulation line

Holding frame

At least

50 cm

Install at least 50 cm

above the snow

accumulation line.

Anchor

bolts

Front

Flare at

indoor unit side

Flare at

outdoor unit side

Flare nut

Half union

Externally

threaded side

Internally

threaded side

Use a wrench to secure. Use a torque wrench to tighten.

Obliquity Roughness Warp

CAUTION

Refrigerant Piping Connection

1. Cut the pipe with a pipe cutter.

2. Insert a ﬂare nut into the pipe and ﬂare the pipe.

• Projection margin in ﬂaring : A (Unit : mm)

RIDGID (clutch type)

IMPERIAL (wing nut type)

Outer dia. of copper pipe R410A

Ø6.35 1.5 to 2.0

Ø9.52 1.5 to 2.0

Ø12.70 2.0 to 2.5

Align the centers of the connecting pipes and tighten the ﬂare nut as far as pos-

sible with your ﬁngers. Then tighten the nut with a spanner and torque wrench

as shown in the ﬁgure.

Tightening connection

Do not apply excess torque. Otherwise, the nut may crack depending on

the conditions.

(Unit : N·m)

Outer dia. of copper pipe Tightening torque

Ø6.35 mm 16 to 18 (1.6 to 1.8 kgf·m)

Ø9.52 mm 30 to 42 (3.0 to 4.2 kgf·m)

Ø12.70 mm 50 to 62 (5.0 to 6.2 kgf·m)

Outer dia.

of copper pipe R410A tool used Conventional tool

used

Ø6.35 0 to 0.5 1.0 to 1.5

Ø9.52 0 to 0.5 1.0 to 1.5

Ø12.70 0 to 0.5 1.0 to 1.5

• Tightening torque of ﬂare pipe connections

The operating pressure of R410A

is higher than that of R22 (approx.

1.6 times). It is therefore necessary

to ﬁrmly tighten the ﬂare pipe

connecting sections (which connect

the indoor and outdoor units) up to the

speciﬁed tightening torque. Incorrect

connections may cause not only a

gas leakage, but also damage to the

refrigeration cycle.

Flaring

Die Pipe

2. Put water in the drain pan and make sure that the water is drained out of

doors.

3. When connecting extension drain hose, insulate the connecting part of

extension drain hose with shield pipe.

Evacuating

After the piping has been connected to the indoor unit, you can perform the

air purge together at once.

AIR PURGE

Evacuate the air in the connecting pipes and in the indoor unit using a

vacuum pump. Do not use the refrigerant in the outdoor unit. For details,

see the manual of the vacuum pump.

Be sure to use a vacuum pump with counter-ﬂow prevention function so that

inside oil of the pump does not ﬂow backward into pipes of the air conditioner

when the pump stops.

(If oil inside of the vacuum pump enters the air conditioner, which use R410A,

refrigeration cycle trouble may result.)

1. Connect the charge hose from the manifold valve to the service port of the

packed valve at gas side.

2. Connect the charge hose to the port of the vacuum pump.

3. Open fully the low pressure side handle of the gauge manifold valve.

4. Operate the vacuum pump to start evacuating. Perform evacuating for

about 15 minutes if the piping length is 20 meters.

(15 minutes for 20 meters)

(assuming a pump capacity of 27 liters per minute) Then conﬁrm that the

compound pressure gauge reading is –101 kPa (–76 cmHg).

5. Close the low pressure side valve handle of the gauge manifold valve.

6. Open fully the valve stem of the packed valves (both gas and liquid sides).

7. Remove the charging hose from the service port.

8. Securely tighten the caps on the packed valves.

Using a vacuum pump

CAUTION

• KEEP IMPORTANT 5 POINTS FOR PIPING WORK.

(1) Take away dust and moisture (inside of the connecting pipes).

(2) Tighten the connections (between pipes and unit).

(3) Evacuate the air in the connecting pipes using a VACUUM PUMP.

(4) Check gas leak (connected points).

(5) Be sure to fully open the packed valves before operation.

Packed valve handling precautions

• Open the valve stem all the way out, but do not try to open it beyond the

stopper.

• Securely tighten the valve cap with torque in the following table:

Pipe size of Packed Valve Size of Hexagon wrench

12.70 mm and smallers A = 4 mm

15.88 mm A = 5 mm

Cap Cap Size (H) Torque

Valve Rod Cap

H17 - H19 14~18 N·m

(1.4 to 1.8 kgf·m)

H22 - H30 33~42 N·m

(3.3 to 4.2 kgf·m)

Service Port Cap

H14 8~12 N·m

(0.8 to 1.2 kgf·m)

H17 14~18 N·m

(1.4 to 1.8 kgf·m)

Hexagon wrench

is required.

Service Port Cap

Valve Rod Cap

Packed valve at liquid side

Service port (Valve core (Setting pin))

Packed valve at gas side

Vacuum

pump

Vacuum pump adapter for

counter-ﬂow prevention

(For R410A only)

Charge hose

(For R410A only)

Handle Hi

(Keep full closed)

Manifold valve

Pressure gauge

Compound pressure gauge

Handle Lo

Charge hose

(For R410A only)

Connecting pipe

–101 kPa

(–76 cmHg)

ELECTRICAL WORKS

The power supply can be selected to connect to indoor unit or outdoor unit. Choose proper way and connect the power supply and connecting cable by follow

the instruction as following.

Wiring Connection

Indoor unit Outdoor unit

Valve cover

Terminals block

How to install the air inlet grille on the indoor

unit

• When attaching the air inlet grille, the contrary of the removed operation is

performed.

Wiring of the connecting cable can be carried out without removing the

front panel.

1. Remove the air inlet grille.

Open the air inlet grille upward and pull it toward you.

2. Remove the terminal cover and cord clamp.

3. Insert the connecting cable (according to the local cords) into the pipe

hole on the wall.

4. Take out the connecting cable through the cable slot on the rear panel so

that it protrudes about 20 cm from the front.

5. Insert the connecting cable fully into the terminal block and secure it

tightly with screws.

6. Tightening torque : 1.2 N·m (0.12 kgf·m)

7. Secure the connecting cable with the cord clamp.

8. Fix the terminal cover and air inlet grille on the indoor unit.

Cord clamp

Terminal cover

Screw

Screws

Air inlet grille

Front panel

1. Remove the valve cover, the electric parts cover and the cord clamp from

the outdoor unit.

2. Connect the connecting cable to the terminal as identiﬁed by the

matching numbers on the terminal block of indoor and outdoor unit.

3. Insert the power cord and the connecting cable carefully into the terminal

block and secure it tightly with screws.

4. Use vinyl tape, etc. to insulate the cords which are not going to be used.

Locate them so that they do not touch any electrical or metal parts.

5. Secure the power cord and the connecting cable with the cord clamp.

6. Attach the electric parts cover and the valve cover on the outdoor unit.

Model RAS-05, 07BKV-E RAS-10BKV-E RAS-13BKV-E RAS-16BKV-E

Power source 50Hz, 220 – 240 V Single phase

Maximum running current 5.0A 6.7A 7.1A 8.0A

Circuit breaker rating 6.5A 8.5A 9.0A 10.0A

Power supply cable H07RN-F or 60245 IEC66 (1.5 mm2or more)

Connecting cable

Altri manuali per RAS-05, RAS-07

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Toshiba Condizionatore d'aria split

Toshiba

Toshiba RAV-SM1603AT-E Manuale utente

Manuali Condizionatore d'aria split popolari di altre marche

Sanyo

Sanyo SAP-K181A Manuale operativo

Daikin

Daikin RZQ71D3V1B Manuale utente

Mirage

Mirage IAEH181A Manuale utente

Daikin

Daikin SkyAir FCAHG71GVEB Guida utente

Fujitsu

Fujitsu ASYA07LCC Manuale utente

MUND CLIMA

MUND CLIMA MUP-12+062X2C Manuale utente

Haier

Haier AS09SH1ERA/1U09EH1ERA Manuale utente

Daikin

Daikin AVA125AMVE Manuale utente