2M Technology 2MTHWT-HMD Manuale utente

WALKTHROUGH METAL DETECTOR

Body Temperature Measurement

2MTHWT-HMD

Quick Guide

Manual Version: V6.1

REV06122020

Body Temperature Measurement – Quick Guide V 6.1

Disclaimer

The infrared temperature measuring device is the human body surface temperature

screening instrument. The test results only reﬂect the real-time temperature evaluation

of objects or people in a speciﬁc environment. The selling company and the manufacturer

shall not bear any responsibility for the direct or indirect loss caused by the use of the test

results.

Installation precaution

It is recommended to install it indoor free from wind. The cold wind might inﬂuence the

accuracy in windy outdoor. In this case, we have to increase the environment temperature

compensation, 5° C per time.

The temperature measurement area should be protected from sunlight to avoid high results.

When it is used outdoor under special circumstances, build a shed on site. The height of

the shed should be more than 2.4m (7.87ft) to ensure the stability and free from wind.

People walk slowly through it to measure thetemperature.

Temperature measurement module

Temperature sensor:

Real time infrared thermo sensor to detect temperature,

ready in 30 seconds after power on.

Distance sensor:

The distance sensor starts working when a person or

object is in 20cm (7.87” in) to it. If the temperature of person

or object detected is ≥ 35.5 ℃, the voice "Normal

temperature" is trigged; if it's lower than 35.5 ℃, or higher

than the set value with alarm, the voice "Please check

again" is trigged.

When the ambient temperature is lower than 15 ℃, if the

temperature of person or object detected is ≥ 34.5 ℃, the voice

"Normal temperature" is trigged; if it's lower than 34.5 ℃, or higher

than the set value with alarm, the voice "Please check again" is

trigged.

Special attention: the distance sensor shallnot be blocked,

otherwise it will repeat the voice broadcast.

Power Light:

The indicator light is on when the temperature measurement

module is working. When measuring the foreheadtemperature,

the measured result is the most accurate when the middle of

human eyes is right facing the temperature indicator.

Temperature Measurement

Power Light

Distance sensor

Temperature sensor

Sketch Map

Body Temperature Measurement – Quick Guide V 6.1

Interface

Alarm count of over temperature

and metal detected,

Shifted by button Power

Body temperature and Metal

safety pass count

Shifted by button Power

Temperature sensor

Power Select Adjust Conﬁrm

A B C D

Connection

Connect the wires with the right colors one by one.

Wrong connection may damage the temperature measurement module.

Body Temperature Measurement –Quick Guide V 6.1

Power Select Adjust Conﬁrm

Commission instruction

Step 1, press D button to enter below:

Password input

Step 2, press B to shift and C to adjust to enter the password 1318, press D button to enter below:

Temperature compensation

settings

Alarm temperature setting

Remark:

“345” means the starting value of normal temperature voice broadcast is 34.5 ° C.

“370” means the alarm temperature is 37 ° C .

The default alarm value by factory is 37 ° C.

Step 3, after setting the temperatures, press D to back.

Step 4, press D button, then press B to shift and C to adjust to enter the password 1319, press D button to enter

below:

Ambient temperature

compensation settings

Remark:

1) The default environment temperature value by factory is 25 ° C. It's applicable in most situation and no need to

adjust. If necessary, it can be adjust. If we decrease it by 10° C, the body temperature will decrease 1° C. If we

increase it by 10° C, the body temperature will increase 0.5° C.

Step 5, after setting the ambient temperature, press D button for 3 seconds to back

Power Select Adjust Conﬁrm

Power Select Adjust Conﬁrm Power Select Adjust Conﬁrm

Power Select Adjust Conﬁrm

Body Temperature Measurement – Quick Guide V 6.1

Temperature unit switching

Press B button in the main interface, it shows F or C. F represents Fahrenheit, C represents Celsius.

Press A button for 3 seconds to adjusting interface. Press A button twice to main interface. Press B and A to

adjust if necessary.

Restore factory settings

Press D button in the main interface (display CCCC). Press B button to enter the password input interface (display

1234). Press B button to shift and press C to adjust and enter the password 1264. Press D button to display FFFF,

indicating the pass word is correct. Press B button to enter the function setting interface (display P001). Press B button

to shift to d001. Press C button to change 0 to 1, and press D button to complete the setting (display 0000). Press A

button twice to return to the main interface. When the device is not working properly, please restore factory settings.

Low temperature prompt setting

Press D button (display CCCC) in the main interface, press B button to enter the password input interface (display

1234), and press B button and C button to input the password 1322. Press D button to show FFFF, indicating the

password is correct. Press B button to enter the function setting interface (display _ _ _ 2), Press B button to ﬁnd 2.

Press C button to change 2 to 1. Press D button to complete the setting (display 0000), and press A twice to return to

the main interface.

●

"2" means to turn on low temperature voice broadcast "please check again";

●

"1" means to turn off low temperature voice broadcast "please check again".

0000

Power Select Adjust Conﬁrm

36.5

Power Select Adjust Conﬁrm

0000

Power Select Adjust Conﬁrm

36.5

Power Select Adjust Conﬁrm

36. 50000

1234

0000

1264

0000

FFFF

0000

P001 d001

d001

36. 5

36. 50000

1234

0000

1322

0000

FFFF

---2

1322 1322

---1

36. 5

Body Temperature Measurement – Quick Guide V 6.1

Language settings

Press D button in the main interface (display CCCC), press B button to enter the password input interface (display

1234), and press B button and C button to input the password 1323. Press D button to display FFFF, indicating the

password is correct. Press B button to enter the function setting interface (display _ _ _ E).

Press B button to switch and ﬁnd E. Press D button to change E to C. Press D button to complete the setting

(display 0000). Press A twice to returns to the main interface.

●

"E" means English voice broadcast;

●

"C" means Chinese voice broadcast.

●

More languages setting is upon request.

Distance sensor debugging

Press D button in the main interface (display CCCC), press B button to enter the password input interface (display

1234), and press B button and C button to input the password 1321. Press D button to display FFFF, indicating the

password is correct. Press B button to enter the function setting interface (display 0200). Press B button to shift and C

button to adjust the distance value. Press D button to complete the setting (display 0000). Press A button twice to

return to the main interface.

●

"0200" means the effective distance between the thermal sensor and the target is within 20cm (7.87” in).

When a Target comes close within 20cm (7.87” in), it triggers the thermal sensor to work.

●

When the distance is set to 0100, the temperature result is the most accurate.

The number of 8190 or 8191, showing in the ﬁrst line, is the initial value of the distance sensor, which means there is

no obstruction 130cm (51.18” in) in front of the thermal sensor. In this situation, if you block the thermal sensor with

your hand at 20cm (7.87” in) in the front of the thermal sensor, you will see 0200 at the second line (with an error of

about 1 cm (0.39” in)).

If there is no object blocking but a different number ﬂashes in the ﬁrst line, it means that the distance sensor is

interfered. In this situation, the voice of "Please check again" is repeated. We have to eliminate the interference

Metal detection off setting

Press D button in the main interface (display CCCC), press B button to enter the

Password input interface (display 1234), and press B button and C button to adjust to input the password 1111. Press D

button to display FFFF, indicating the password is correct. Press B button to enter the function setting interface (display

L001/975). Press B button to shift and C button to adjust to change 975 to 0.

Press B button to display L002/975, and press B button to shift and C button to adjust to change 975 to 0.

Change the second line of L003-L006 from 975 to 0 in this way.

Press B button to switch to D001, and press D button to complete the setting (display 0000). Press A button twice to

return to the main interface.

Body Temperature Measurement – Quick Guide V 6.1

●

L001-L006 of the ﬁrst line is the metal detection zone from bottom to top, 975 (or other values) of the

second in represents the metal detection sensitivity, high sensitivity for tiny metals.

●

D001 of the ﬁrst line is the alarm time setting, and 1.0 of the second line means the alarm time is 1 second.

……

Metal detection on setting

Press D button in the main interface (display CCCC), press B button to enter the password input interface

(display 1234), and press B button to shift and C button to adjust to input the password 1111. Press D button

to display FFFF, indicating the password is correct. Press B button to enter the function setting interface

(display L001/975). Press B button to shift to

L 007 / 0 ,

and press B button to shift and C button to adjust to

change 0 to 975.Press B button to shift to d001 option, and press D button to complete the setting (display

0000). Press A button twice to return to the main interface.

●

L007 of the ﬁrst line represents all the 6 metal detection zones. The number 975 of the second line

represents the metal detection sensitivity.

●

L008 of the ﬁrst line is the setting to detect small size metals. The number 1 of the second line represents

to detect small size metals, and 50 means not detect small size metals.

●

D001 of the ﬁrst line is the alarm time setting, and 1.0 of the second line means the alarm time is 1 second.

Instruction of temperature measurement

Power on and wait for 30 seconds, keep nothing in front of the temperature sensor.

Normal ambient temperature is 0°C - 35°C. When using it at - 10°C, you have to decrease the

environment temperature compensation, 5°C per time, until the result difference between it and the

forehead thermometer is less than

0.3°C.

Measurement method: Measure forehead or wrist surface

Forehead temperature and wrist surface temperature can be measured without adjusting settings.

Measurement area: the center of forehead or the wrist covered by sleeve.

Standard measurement distance: 1cm-10cm (0.39”-3.93” in). When measuring at a distance of 10-30cm

(3.93”- 11.81” in), it is necessary to adjust the environment temperature compensation, 5°C per time,

until the result difference between it and the forehead thermometer is less than

0.3°C.

36. 50000

1234

0000

1111

0000

FFFF

975

L 001 L 001

36. 50000

1234

0000

1111

0000

FFFF

975

L 001 L 007

975

L 007

1. 0

d001

0000

36. 5

975

L 006

1. 0

d001

0000

36. 5

L 006

Body Temperature Measurement – Quick Guide V 6.1

Measurement time: 0.5 seconds. After the measurement, please leave quickly. Otherwise the

measurement will be repeated.

During the temperature measurement, inﬂuenced by the measurement speed, the temperature might

suddenly ﬂuctuate up and down. In this case, please measure the body temperature 3-5 times

continuously, and take the average value as the ﬁnal measurement result.

The instrument automatically detects the temperature of the object in 20cm (7.87” in) in front of it. After

measuring the temperature, we have to move our hand or forehead away. If we keep close to the sensor

for long time, it will stop working asa protection.

Common trouble shooting

Metal detection does not count Processing method: press the power key to switch from the

temperature measurement interface to the metal detection and counting display interface.

The temperature cannot be measured when the machine is started Treatment: wait for 30 seconds after power

on, and then measure the temperature.

Low temperature measurement Processing method: check whether the value set in 1319 interface is 25, if not,

change to 25. And then use the hand-held electronic infrared Thermometer comparison test, if the measured

values are consistent, it means that the equipment is working normally. If there is a deviation greater than 0.5 ℃,

please refer to Debugging is described on the second page.

Temperature measurement is not sensitive Treatment: when measuring body temperature, stay at the

target measured by infrared temperature sensor for 1 second.

Metal detection sensitivity is too high Processing method: the setting item L008 in function setting password 1111

is changed from 1 to 50, excluding small metal parts.

Network connection failure Processing method: check whether the IP address of the computer is completely

consistent with the instructions. If not, please set the IP address according to the instructions, if it is

consistent, please refer to the video and operate again.

Body TemperatureMeasurement – Quick Guide V 6.1

1-1

Infrared Temperature Sensor

Schematic diagram of temperature measurement

Altri manuali per 2MTHWT-HMD

Indice

Altri manuali 2M Technology Rilevatore di metalli

2M Technology

2M Technology 2MTHWT-HMD-II Manuale utente

Manuali Rilevatore di metalli popolari di altre marche

Garrett

Garrett MAGNASCANNER CS 5000 Manuale utente

Valex

Valex 1800200 Manuale utente

Gauss

Gauss MIL MD Manuale utente

Velleman

Velleman CS130 Manuale utente

Sears

Sears 321.596370 Manuale utente

Eriez

Eriez X8 Manuale utente

Steinberg Systems

Steinberg Systems SBS-MD-22 Manuale utente

Zircon

Zircon MetalliScanner m60c Manuale utente

nalanda

nalanda MD027 Manuale utente

REV Ritter

REV Ritter CB-7005 Manuale utente

Minelab

Minelab F1A4 Manuale utente

Fisher Research Labs

Fisher Research Labs F70 Manuale utente

Steinberg Systems

Steinberg Systems SBS-MD-12 Manuale utente

GOLDEN MASK

GOLDEN MASK 5 Manuale utente

Grizzly

Grizzly YM 203 Manuale utente

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Manuale utente

Treasure Cove

Treasure Cove Vibra-Probe 560 Manuale utente

Accurate Locators

Accurate Locators XL16 IMAGER Manuale utente