3Com 4200G Series Manuale utente

3Com Switch 4200G

10G Interface Module

Installation Guide

1. XFP Interface Module

1.1 Appearance and front panel

Figure 1 Appearance of an XFP interface module

Figure 2 Front panel an XFP interface module

1.2 Installation

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded. Then remove the XFP interface module from the package.

Step 2: Loosen the filler panel mounting screws on the rear panel of the

switch with a screwdriver and remove the filler panel.

Step 3: Hold the fastening screws on the front panel of the XFP interface

module, and gently push the module in along the slot guide rail until the

module is in close contact with the switch.

Step 4: Tighten the fastening screws with a screwdriver to secure the XFP

interface module.

(1)

(2)

(4)

(3) (1)

(2)

(4)

(3)

(1): Switch (2): Optional module slot

(3): XFP interface module (4): Push-in direction

Figure 3 Installing an XFP interface module

Note: (1) Store the filler panel for future use.

(2) When tightening the fastening screws at both sides of the

optional module with a screwdriver or an electric screwdriver,

make sure that the torque is not bigger than 0.4 N-m.

1.3 Removal

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded.

Step 2: Loosen the fastening screws at both sides of the XFP interface

module using a screwdriver.

Step 3: Pull the XFP interface module towards you, until it completely

comes out of the switch chassis.

Note: When installing or removing an optional interface module, pay

attention to the following points:

(1) Do not use too much force in the operation, and do not

touch the surface-mounted components directly with your

hands.

(2) After removing an optional module, if no new module is to

be installed, install the filler panel as soon as possible to

prevent dust and ensure the normal ventilation in the switch.

2. XENPAK Optical Module

2.1 Appearance and front panel

Figure 4 Appearance of a XENPAK optical module

Figure 5 Front panel of a XENPAK optical module

2.2 Installation

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded. Then remove the XENPAK optical module from the package.

Step 2: Loosen the two mounting screws on the small cover plate in the

middle on the filler panel with a screwdriver and remove the small cover

plate.

Note: When installing a XENPAK optical module, you do not need to

remove the entire filler panel. Just remove the small cover

plate in the middle on the filler panel.

Step 3: Hold the fastening screws on the front panel of the XENPAK

optical module, and gently push the XENPAK optical module in along the

slot guide rail until the XENPAK optical module is in close contact with the

switch.

Step 4: Tighten the fastening screws on the XENPAK optical module with

a screwdriver to fix the XENPAK optical module on the filler panel.

(1): Switch (2): Filler panels for optional module slots

(3): Small cover plate (removed) in the middle on the filler panel

(4): Push-in direction (5): XENPAK Optical Module

Figure 6 Installing a XENPAK optical module

Note: (1) Retain the small cover plate for future use.

(2) Do not tighten the module screws more than 0.4 Nm.

(3) The switch 4200G supports hot swapping of XENPAK

optical modules.

2.3 Removal

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded.

Step 2: Loosen the fastening screws at each side of the XENPAK optical

module using a screwdriver.

Step 3: Pull the XENPAK module until it comes out of the switch chassis.

3Com Corporation 350 Campus Drive

Marlborough, Massachusetts 01752-3064 USA

www.3Com.com

Part Number: 10014918 Rev.AA

Published July 2006

Altri manuali per 4200G Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali 3Com Hardware di rete

3Com

3Com 3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card... Manuale utente

3Com

3Com NETBuilder II Manuale utente

3Com

3Com OfficeConnect Manuale utente

3Com

3Com 3C16075 Manuale utente

3Com

3Com Switch 4210 9-Port Manuale utente

3Com

3Com 3C421600A Manuale di programmazione

3Com

3Com OfficeConnect WX4400 Manuale utente

3Com

3Com WL-311 Manuale utente

3Com

3Com 3CR10551A-US - Asterisk IP Communications... Manuale utente

3Com

3Com SuperStack 3 4900 Manuale utente

3Com

3Com WL-560 Manuale utente

3Com

3Com 3C16630A Manuale utente

3Com

3Com 3CRWEASY96A Manuale utente

3Com

3Com 3CRX5DV-U-96-ME - X5 Unified Security... Manuale utente

3Com

3Com SuperStack II 3C16971 Manuale utente

3Com

3Com FDDI MMF Manuale utente

3Com

3Com OfficeConnect WX2200 Manuale utente

3Com

3Com WL-308 Manuale utente

3Com

3Com AirConnect Manuale utente

3Com

3Com 3C433279A Manuale di istruzioni

3Com

3Com SWITCH 4050 Manuale utente

3Com

3Com DUAL SPEED HUB/PS HUB CASCADE CONVERTER Manuale utente

3Com

3Com H3C S3100 16C SI Manuale utente

3Com

3Com 3C421600A Manuale di istruzioni

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente