3D R Solo Manuale utente

Thermal Gimbal

for the

3DR SOLO

Installation Instructions

P.O. Box 4242 Middletown, New York 10941 USA

Phone: 1-888-919-2263 | Outside the U.S.: +1-845-343-4077 | Fax Line: +1-845-343-4299

Version 1.3

10MAR2017

THERMAL GIMBAL FOR 3DR SOLO MANUAL

Safety Notes

SAFETY NOTES:

Product Notes:

•Do not disassemble or attempt to repair the product by yourself.

•Do handle the product properly. This product may be damaged ifdropped.

•Do not use corrosive, alcoholic or organic-solvent-containing cleaners to wipethis

product.

•Do not use or store this product in high temperature environment.

•If the product is quickly transferred from a low temperature environment to a high

temperature environment, water condensation may occur in the product due to physical

changes. In this case, it is recommended to wait until the product returns to room tem-

perature before turning iton.

•Store the product in a dry and clean environment when storing the product for a long

period of time.

•Do not disconnect the power or turn the product off during firmware updating process.

Doing so may cause incorrect data to be written and the product may not power onlater.

•After using the product in the presence of sand, mud or other foreign matter, wipe the

gimbal with a clean, dry, lint-free cloth.

•This product is intended for use solely with the FLIR VUE, FLIR VUE PRO andFLIR

VUE PRO-R Series of Thermal ImagingCameras.

Do not Use this product with any other device other than the 3DR Solo as it may cause

damage to the gimbal assembly or the other device it is connected to.

THERMAL GIMBAL FOR 3DR SOLO MANUAL

Modification Notice & Instructions

MODIFICATION NOTICE & INSTRUCTIONS:

NOTICE:

In order to take advantage of the controlling features, the FLIR VUE PRO and

FLIR VUE PRO-R Thermal Imaging Cameras will require a modification. This modification can

be performed by OEM Cameras at no charge and the warranty on your thermal camera will not

be void.

You will be able to control all parameters remotely on the FLIR VUE via the 3DR Solo APP

directly out of the box with no camera modifications required.

For the FLIR VUE PRO/VUE PRO-R modifications, please contact OEM Cameras for a Return

Authorization and shipping instructions to our facility in New York.

•

E-Mail:

[email protected]

• Toll Free: 1-888-919-2263

• Outside the US: +1-845-343-4077

The VUE PRO Series modifications will allow you to control the following parameters remotely

via the 3DR Solo APP:

•

Color Palette: - 3 Choices

•

Camera Digital Zoom: 1x, 2x, 4x

•

Flat-Field Correction/FFC (Manual)

•

Region of interest (ROI): - 3Choices

•

Scene Presets: - 3 Choices

•

Start and Stop Image Sequence or Video Capture on the VUE PRO or VUE PRO-R’s

Internal Micro SDCard

On the VUE PRO and PRO-R at this time only two (2) parameters can be set and adjusted

remotely. These parameters are set by connecting to the camera via Bluetooth using the FLIR

VUE PRO APP on your iOS or Android Device.

iOS APP: http://apple.co/2dT688Q

Android APP: http://bit.ly/2eyC0jj

Without VUE PRO or VUE PRO-R modifications, you will only be able to view the cameras

images on your iOS or Android device and Record or Capture images on your iOS or Android

device using the 3DR Solo APP.

THERMAL GIMBAL FOR 3DR SOLO MANUAL

FLIR VUE/VUE PRO Installation

CONNECTING THE GIMBAL TO THE VUE/VUE PRO SERIES THERMAL CAMERAS:

In this section we will show how to:

•

Connect the FLIR VUE Thermal Camera to theGimbal

•

Connect the FLIR VUE PRO / PRO-R Thermal Camera to theGimbal

NOTE: THE VUE SERIES CAMERAS SHOULD BE INSTALLED TO THE GIMBAL BEFORE

ATTACHING THE GIMBAL TO THE 3DR SOLO.

Before installing the camera to the Gimbal, please remove the battery and any other power source

that may be connected.

FLIR VUE PRO-R USERS:

Before you begin, please remove the FLIR

band attached to the outside of the Thermal

Camera. There are four allen screws. Store in

a safe place for future use.(Fig. 1)

There are three steps for attaching the FLIR VUE

Series Thermal imaging camera to the Gimbal.

Step 1:

With the supplied allen key, detach the cover plate

by removing the short allen-head screw on the side

of the gimbal and set aside. (Fig. 2&3)

THERMAL GIMBAL FOR 3DR SOLO MANUAL

FLIR VUE/VUE PRO Installation

CONNECTING THE GIMBAL TO THE VUE/VUE PRO SERIES THERMAL CAMERAS:

Step 3:

Plug the USB connector on the gimbal, intothe

VUE Series Camera and secure using the four

short allen-head screws provided. (Fig. 6)

Step 2:

Align to the USB Connector to the cover plate.

The holes are aligned differently on the VUE

PRO/PRO-R. (Fig. 4&5)

Use the long allen-head screws provided, to

mount the plate on the camera.

THERMAL GIMBAL FOR 3DR SOLO MANUAL

Installing theGimbal

GIMBAL INSTALLATION:

In this section we will show how to:

•

Disconnect the Current Gimbal.

•

Connect the Thermal Gimbal Assembly to the 3DR SOLO.

Before You Begin:

Before installing, please remove the battery or any power source from the 3DR SOLO.

Removing the cover plate:

If there is no Gimbal attached, the cover

plate will need to be removed. The plate

is attached with three screws on the 3DR

SOLO. Loosen the self retaining screws

with the provided Phillips screwdriver.

Store the plate in a safe place for future

use. (Fig. 7)

There are two cables inside the body of the

3DR SOLO. Carefully bring them out of

the drone. They will connect to the board

of the Gimbal in the steps following this

procedure. (Fig. 8)

THERMAL GIMBAL FOR 3DR SOLO MANUAL

Installing theGimbal

GIMBAL INSTALLATION:

Uninstalling your current Gimbal Assembly:

If you have a gimbal currently attached to the SOLO, it will need to be re-

moved before installing the 3DR Solo Thermal Gimbal Assembly.

Loosen the three self retaining screws with

the provided Phillips screwdriver.

Carefully lift up the Gimbal assembly from

the drone while pressing in on the two tabs

near the front legs. (Fig. 9)

The Gimbal should release.

Carefully lift off, and set in front of the

SOLO as shown.

The two cables attached will need to be

disconnected. (Fig. 10)

THERMAL GIMBAL FOR 3DR SOLO MANUAL

Installing theGimbal

GIMBAL INSTALLATION:

Disconnect the Power / Data Cable by pressing

the locking tab and gently lifting the connec-

tor straight up from the board as shown: (Fig.

11&12)

To disconnect the HDMI cable, gently sepa-

rate the cable from the connection by pulling

away from the board. (Fig. 13&14)

Once you have disconnected both cables,

store the existing gimbal in a safe place for

future use.

THERMAL GIMBAL FOR 3DR SOLO MANUAL

Installing theGimbal

GIMBAL INSTALLATION:

The Philips screwdriver (included), will be the only tool needed for installation.

Before connecting:

The three position Camera Select Switch will allow the thermal gimbal to pass certain information

to the remote controller and the 3DR Solo App.

Be sure to select the correct position before connecting the HDMI cable.

Position 1 - FLIR VUE CAMERA:

This position allows the control of the FLIR VUE

and adjustments through the 3DR App.

Position 2* - FLIR VUE PRO/PRO-R Camera:

This position allows the control of the VUE

PRO or VUE PRO-R. Adjustments can be made

through the 3DR App.

Position 3* - This position will disable control

through the 3DR App and pass MAVLINK/GPS

Data from the SOLO to the VUE PRO and VUE

PRO-R. (Fig. 15)

(

*See Page 3 for Modification Details.

)

When the desired toggle switch position has

been selected, connect the HDMI Cable to the

HDMI port and the Gimbal Data Cable to the

port as shown. (Fig. 16)

THERMAL GIMBAL FOR 3DR SOLO MANUAL

Attaching theGimbal

ATTACHING THE GIMBAL ASSEMBLY TO THE 3DR SOLO:

Attaching the Gimbal to the 3DR SOLO:

Tuck the excess cable into the 3DR SOLO

making certain that the wires are not pinched

between the seams. (Fig. 17)

With the screwdriver provided, tighten the

three mounting screws to secure the gimbal to

the 3DR SOLO.

The 3DR Thermal Gimbal is now installed and

ready for flight testing.

Flight Testing:

Follow the pre-flight testing procedures as per

the operating manual for the 3DR Solo. (Fig.

19)

Gently place the gimbal assembly into

position.

The three mounting screws should line up

with the holes on the SOLO. (Fig. 18)

Altri manuali per Solo

Indice

Altri manuali 3D R Accessori per fotocamere

3D R

3D R LiveView Manuale utente

Manuali Accessori per fotocamere popolari di altre marche

Viltrox

Viltrox EF-NEX Istruzioni per l'installazione

Calumet

Calumet 7100 Series CK7114 Manuale utente

Ropox

Ropox 4Single Series Manuale utente

Cambo

Cambo Wide DS Digital Series Istruzioni operative

Samsung

Samsung SHG-120 Manuale utente

Ryobi

Ryobi BPL-1820 Manuale operativo

Aegis

Aegis ABL-36020P Manuale utente

Pentax

Pentax Data Back Fc Manuale utente

Fantasea

Fantasea EyeGrabber F Series Manuale utente

Honeywell

Honeywell HDZ20HD Manuale utente

EGO

EGO BA1400T Manuale utente

Sima

Sima SRW-62 Manuale utente

Shape

Shape A7SSMKIT Manuale utente

Slide Kamera

Slide Kamera HST-2 Manuale utente

Power works

Power works 2902613 Manuale utente

SES

SES SE-2047-2 Manuale utente

Olympus

Olympus PT-EP05L Manuale utente

Starlite

Starlite OctoDome nxt Manuale utente