3M 4604 Manuale utente
June 1998
34-7045-6337-7-A
Re-enterable PST Dome Closure
Instructions
2
3
Contents:
1.0 General.......................................................................................................................................................... 4
2.0 Kit Contents ................................................................................................................................................... 4
3.0 PST Closure Capacity ................................................................................................................................... 5
4.0 Cable Preparation ......................................................................................................................................... 5
5.0 Bonding and Grounding ................................................................................................................................ 6
6.0 Splicing .......................................................................................................................................................... 6
7.0 4604 and 4606 Closure Installation .............................................................................................................. 7
8.0 4608 and 4608XL Closure Installation .......................................................................................................... 10
9.0 Closure Re-entry ........................................................................................................................................... 13
10.0 Retrofit on PST Pedestal Splice Closures .................................................................................................... 13
4
1.0 General
The 3M™Re-enterable PST Dome Closure is used for new and existing above-ground splices contained
within a pedestal.
2.0 Kit Contents
2.1 Additional Materials Required
Vinyl Tape
Shield Bond Connectors
Splice Connectors
Note: All components must be installed per instructions to be effective.
4608 and 4608XL Closures
Closure Assembly (A)
Dome
Base
O-ring
Latch
Gel End Seal Core (B)
Gel Sealant Strip (C)
PST (D)
Ground Wires (E)
Desiccant Bag (F)
Sheath Scuff (G)
Base Plate (H)
4604 and 4606 Closures
Closure Assembly (A)
Dome
Base
O-ring
Latch
Gel End Seal Core (B)
Gel Sealing Strip (C)
PST (D)
Ground Wires (E)
Desiccant Bag (F)
Sheath Scuff (G)
(D)
(G)
(H)
(F)
(B)
(C)
(E)
(A)
(D)
(A)
(B)
(G)
(C) (E)
(F)
5
3.0 PST Closure Capacity
(W x D)
(H)
Closure
Outside Dim.
22.5"
(572 mm)
-
Closure
Height
Approx. Bundle
Diameter
Minimum Reliable
CAD Pedestal
Main
Cables
Terminal
Cables
Branch
Cables
Drop
Cables
*Approx.
Splice Range
2.5"
(64 mm) 3.9"
(99 mm)
0.4" - 0.6"
(10 - 15 mm) 0.4" - 0.6"
(10 - 15 mm)
0.7" -1.0"
(18 - 25 mm)
100 pr. - MS2
50 pr. - UR 300 pr. - MS2
100 pr. - UR
4604 4606 4608 4608XL
3.8" x 2.8"
(97 x 71 mm) 5.6" x 3.9"
(142 x 99 mm)
0.35" max
(9 mm) max
2 max
0.35" max
(9 mm) max
2 max
0.35" max
(9 mm) max
2 max
0.35" max
(9 mm) max
2 max
7.0" x 5.4"
(178 x 137 mm) 7.0" x 5.4"
(178 x 137 mm)
22.5"
(572 mm) 23.5"
(597 mm) 33.5"
(851 mm)
5.3"
(135 mm) 5.3"
(135 mm)
46 8 12/70
0.5" - 1.1"
(13 - 28 mm) 0.9" - 1.6"
(23 - 41mm) 1.4" - 2.5"
(36 - 64 mm) 1.4" - 2.5"
(36 - 64 mm)
0.4" - 0.8"
(10 - 20 mm) 0.4" - 0.8"
(10 - 20 mm)
0.9" - 1.3"
(23 - 33 mm) 0.9" - 1.3"
(23 - 33 mm)
600 pr. - MS2
300 pr. - UR 900 pr. - MS2
400 pr. - UR
*Note: Based on two bank 4000-DWP and Scotchlok
TM
connectors installed per 3M practices.
Examples: 100 pair means 100 pair In and 100 pair Out or 100 pair straight splice.
4.0 Cable Preparation
4.1 Remove sheath and scuff both
cables as noted for the following
closure sizes.
Preparation A: 4604, 4606, 4608
Preparation B: 4608XL
6"
(151 mm)
23"
(584 mm)
Scuff Both
Cables
Remove Sheath
Preparation A Preparation B
6"
(151 mm)
15"
(381 mm)
Scuff Both
Cables
Remove Sheath
3.1 Overall closure dimensions (See PST Closure Capacity Chart). WD
H
6
5.1 Install bonding connectors per system practice. Bonds
should be placed so that the studs of the connectors are
facing forward.
5.0 Bonding and Grounding
6.0 Splicing
6.1 Splice per company practice.
6.2 Splice in tail of a terminal block when required.
5.3 Insulate bonding connectors by wrapping with vinyl tape.
5.2 Install external ground wires to bonding connector studs
and run along the cables.
7
Note: Place ground wires and drop wires between layers in gel
sealing strip. Ensure wires have one layer of gel between
them and cable sheath. There should be at least 0.25" (6
mm) between wires.
7.3 Install gel end seal core 2" (51 mm) below the sheath opening.
Pull lips of seal, created by cutting and removing plug, around
cables. Remove packaging from gel sealing strip. Wrap the gel
sealing strip around the core and ground wires with a slight
tension.
7.2 Slit gel end seal ports along the length of plugs for desired
number of cables to be installed and remove plugs.
Use plugs 1 and 2 for main cables and plug 3 for branch or
terminal cable.
7.0 4604 and 4606 Closure Installation
7.1 Cut and remove packaging from gel end seal core.
Note: A fourth plug is available on 4606 closure.
8
7.4 Squeeze gel end seal to insure a seal between layers and cables.
Note: Closure assembly must rest on end seal when placed over
the splice. Move end seal upward, if necessary.
7.5 Cut off top of foil bag which contains desiccant at dotted line and
secure bag at base of wire work area with a cable tie.
Note: Carefully follow health, safety and environmental
information given on product label or Material Safety Data
Sheet for desiccant bag.
7.6 Remove cardboard insert and pull core tail through the center of PST
until core is even with PST edge.
7.7 Slide PST over closure so that PST tail is pointed toward the top
of the closure. The core tail MUST be unwound upward.
Position PST bottom edge between the bottom of the wire form
latch and the base's top rib.
Note: Optional method is to put closure over the splice bundle
and position PST 2" (51 mm) below the gel end seal.
While holding the PST and closure with one hand,
unwind the core by pulling on the core tail with the other
hand in an upward and outward COUNTERCLOCKWISE
direction.
9
7.12 Continuously push PST downward while pulling the rest of the
core material.
7.14 For pedestal closure applications, secure the closure to pedestal,
mount terminal block and connect ground wires according to
system practice.
7.13 When the PST is in place, remove the core wrap from around the
cable.
7.9 Push PST towards bottom of closure. This will invert the PST.
Note: Do not force the PST to slide on the closure during inversion.
7.08 While holding the PST and closure with one hand, unwind the core
by pulling on the core tail with the other hand in an upward and
outward COUNTERCLOCKWISE direction until approximately
0.5"(13 mm) of the PST is shrunk onto the closure.
7.11 Place assembly over splice and onto gel end seal. Insure the
wireform latch and the 3M logo are facing forward.
7.10 Pull the core material from the PST until the PST is even with
the bottom of the closure.
10
8.0 4608 and 4608XL Closure Installation
8.1 Cut and remove packaging from gel end seal core.
8.3 Install gel end seal core 2" (51 mm) below the sheath opening.
Pull lips of seal, created by cutting and removing plug, around
cables.
8.5 Remove packaging from small cut gel sealant strip and wrap each
ground wire with the gel piece and press against core.
8.4 Cut a 1" (25 mm) piece from both ends of gel sealant strip to be
used on ground wires.
1
2
3
8.2 Slit gel end seal ports along the length of plugs for desired
number of cables to be installed. Remove plugs.
Use plugs 1 and 2 for main cables and plugs 3 and 4 for branch or
terminal cables.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali 3M Cavi e connettori
3M
3M 8250 Istruzioni per il montaggio
3M
3M TTS-5-1-OJ Guida utente
3M
3M 5321 Manuale utente
3M
3M Scotchlok U1 Series Manuale utente
3M
3M 5811 Series Manuale utente
3M
3M SafeLok Anchorage 4011 Guida
3M
3M 3443-112 Istruzioni per il montaggio
3M
3M 103 12R1-00 Series Manuale utente
3M
3M MS2 Sealant Box 4075-S Manuale utente
3M
3M VF-45 Manuale utente
3M
3M Cold Shrink QT-III 7620-S-INV-3G Series Manuale utente
3M
3M 90-B1 Manuale utente
3M
3M Cold Shrink QS-III Splicing Kit Manuale utente
3M
3M ECAM-27MM-D Manuale utente
3M
3M QCI Series Manuale utente
3M
3M 5415A-IJ Manuale utente
3M
3M Liqui-Cel MM 0.5x1 Series Manuale
3M
3M 36110-3000 Series Manuale utente
3M
3M 8800-APC/AS/AGC Manuale utente
3M
3M 3104 Manuale utente
