4G Systems XSJack T3e Manuale utente
XSJack T3i
User Manual
®
XSJack T3e
®
English
Deutsch
2
3
Introduction
Thank you for choosing the XSJackT3e or XSJackT3i - henceforth
both referred to as XSJackT3. With the XSJackT3 a fax machine and a
telephone can be connected and used in a GSM mobile network.
Scope of delivery
■ XSJackT3e or XSJackT3i
■ Power supply
■ GSM antenna (XSJackT3e only)
■ User manual
Safety information
To protect yourself and the device from damage, please observe the
following when using and handling the XSJackT3:
■ The XSJackT3 is designed solely for use in dry heated rooms.
■ It must be kept away from fire and flames!
■ Do not use the XSJackT3 in areas with potentially explosive
atmospheres.
■ Prevent the device from exposure to direct sunlight or heat.
■ The slots and openings serve to ventilate the device and must
not be covered.
■ The device must not come into contact with liquid as this could
result in electric shock, short-circuiting or total destruction of the
device or worse.
■ Do not open the housing of the XSJackT3. This could cause a
hazard to the user or damage the device.
■ Dispose of the XSJackT3 in accordance with statutory require-
ments. The current disposal guidelines for electrical equipment
can be obtained from any recycling centre. Please also refer to
page 30.
■ Please use the original 4G Systems power supply only.
4
Table of contents
Introduction 3
Scope of delivery 3
Safety information 3
Table of contents 4
Getting to know your XSJackT3 6
Initial Setup 7
Step 1: Inserting the SIM card 7
Step 2: Connecting the antenna 7
Step 3: Connecting a telephone, a fax machine, or both 8
Step 4: Connecting the power supply 9
Step 5: Entering the PIN of your SIM card 9
Entering service codes 10
Telephone operation
11
Making telephone calls 11
Call waiting, call holding and conferences 12
Fax operation
14
Fax setup 14
Fax transmission 14
Fax reception 15
Resetting the fax memory 15
Fax and SIM card types 16
SMS operation 17
Advanced functions 18
Definition of a default area code 18
Roaming 18
Blocking device for outgoing calls 19
SIM card PIN / PUK operations 19
Resetting factory settings 19
Additional network functions 20
Acoustic Monitoring / Babyphone 21
Automatic dial mode 23
5
Appendix 24
Signal tones 24
FAQ 26
Technical data 28
Dimensions for wall mounting 29
Conformity 30
Disposal information 30
6
Getting to know your XSJackT3
ARJ11 jack to connect
telephone and/or fax
machine
BConnector for external
antenna (XSJackT3e only)
CConnector for power supply
DReset button
ESIM card drawer
FPower LED
(green) Off No power
On Device is powered up
Regular flashing An error has occurred
Irregular flashing Fax memory is full (page 15)
GStatus LED
(red) Off Idle mode
On Ongoing voice or fax connec-
tion to GSM network
Flashing There are received faxes and/or
SMS in the memory ready for
delivery (page 15 and 17)
H3 LEDs for
signal
strength and
SIM requests
(green)
All 3 LEDs off Not yet logged into a GSM net-
work
1 LED on Low GSM signal strength
2 LEDs on Medium GSM signal strength
3 LEDs on High GSM signal strength
Left LED flashing The SIM card is blocked, defect
or not available
Middle LED
flashing SIM PUK entry is required
(page 19)
Right LED flashing SIM PIN entry is required
(page 9)
ABCDE
FGH
7
English
Initial Setup
Step 1: Inserting the SIM card
Insert the SIM card into the pull-out SIM card drawer of the XSJackT3.
Then push the drawer in until you hear it snap into place. If you are
unable to open the drawer by hand, use a coin as a tool.
In case the SIM card drawer is completely
pulled out of the device, carefully reinsert
the drawer into the XSJackT3 while not
containing the SIM card. Note that the tray
of the drawer must face to the back of the
XSJackT3
Note: Never remove or insert the SIM
card while the device is connected to the
power supply. This could lead to unexpec-
ted behaviour and even permanent damage to the device or the SIM
card. Disregarding this warning causes a warranty breach.
Step 2: Connecting the antenna
This step only applies for the XSJackT3e. Please screw the supplied
external antenna to the corresponding connector of the XSJackT3e as
shown.
8
Step 3: Connecting a telephone, a fax machine, or
both
Telephone or fax machine:
Connect one end of your RJ-11
telephone cable to the telephone
or fax machine and the other end
into the RJ-11 jack of the
XSJackT3. If you want to use the
XSJackT3 for fax only, it is
nevertheless recommended to
carry out this initial setup proce-
dure with a telephone, as it could
be difficult to enter the required service codes on a fax machine due to
the absence of a telephone receiver or dedicated button to go off hook.
If you do not have an analogue telephone available, refer to page 10.
Telephone and fax machine:
If both a telephone and a fax
machine are to be connected, first
connect the fax machine to the
XSJackT3 as described above.
Afterwards, connect the telephone
to an available RJ-11 jack of the fax
machine. You may want to refer to
the fax machine's user manual for
more information. Please note that
in certain countries the fax machi-
nes may not have this option. In these cases, a country specific adap-
ter cable is needed.
Note: All connected end devices must support dual tone multiple fre-
quency dialling (DTMF). Modems for data connections cannot be
connected to the XSJackT3.
9
English
Step 4: Connecting the power supply
Connect the power supply unit to the XSJackT3
and the other end into a mains socket.
Step 5: Entering the PIN of your SIM card
Your XSJackT3 will now start up and may require the PIN of your SIM
card to be entered, if this security feature is enabled on your card. The
necessity of entering the PIN will be indicated by the rightmost LED
flashing (refer to page 6). If so, lift the telephone receiver, wait for the
corresponding dial tone, press the # key, enter your PIN, and confirm
by pressing the # key again. Depending on if the entered PIN was cor-
rect or not, you will hear a positive or negative acknowledgment tone.
In the latter case, try to enter the PIN again. Check the LEDs and
signal tones since it may also be necessary to enter the PUK now
(refer to page 19). Refer to page 24 for an overview of all tones. The
PIN remains stored in the XSJackT3.
After you have entered the correct PIN code or if your SIM is not PIN-
secured at all, the device will automatically log onto the GSM network,
which may take up to 45 seconds. When the signal strength is shown
and a continued dial tone can be heard in the receiver, the XSJackT3
is ready for operation.
Note: To minimize interference, you should position the XSJackT3, the
antenna, your telephone, and all their cables as far apart as possible.
Ensure an adequate distance between the device and potential
sources of interference such as microwaves or electrical devices with
metal housings or metal objects in general.
,, PIN, ,
10
Entering service codes
Your XSJackT3 is operated and configured using special sequences of
digits you have to enter to the keypad of your connected telephone or
fax machine (0 - 9, *, #).
Fax machines without telephone receiver sometimes feature a dedica-
ted button to go offhook and onhook, which may be indicated by an
icon like a telephone receiver or loudspeaker. Refer to the manual of
your fax machine for additional information.
On devices with telephone receiver or dedicated offhook/onhook
button, proceed as follows:
■ Lift the telephone receiver or press the corresponding button on
your fax machine.
■ Wait for a continuous dial tone audible in the telephone receiver
or from the loudspeaker of the fax machine.
■ Enter the sequence as specified by the format described in the
corresponding tables within this manual. Replace placeholders
written in capital letters inside the format specifications by the
desired numerical values.
■ Wait for a positive or negative command response tone. Some
service codes are provided to query information about specific
settings from the XSJackT3. These codes will answer using the
'Enabled' or 'Disabled' response codes and some will additio-
nally show you numerical values on the display of your phone
via CLIP after going back onhook.
■ Put down the telephone receiver again or press the correspon-
ding button on your fax machine.
Note: Refer to page 24 for an overview of all possible dial tones and
response tones.
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali 4G Systems Modem
