7inova 7W211 Manuale utente

Wireless-N WiFi Repeater 300Mbps

Model: 7W211

QUICK

INSTALLATION

GUIDE

LED indicators’ Status Description

WPS Button

Ethernet

Reset Button

WLAN LED

WPS LED

Ethernet LED

Power LED

Indicator Name

Power Status Indicator

Wireless Status Indicator

WPS Status Indicator

Ethernet Status Indicator

Green On

Green slow blink

Green fast blink

Off

Constant On (Off after 5mins)

Green fast blink

Green On

Get Powered

Wireless Function Launched

WPS Function Launched

Not use or have completed the connection

WPS pairs successfully

Data Transmission via Ethernet

Ethernet Connected

Data Transmission via wireless

Status Description

REPEATER

CLIENT

WPS One Button SetupFunctions Introduction

Before you start to use this device, please check if there’s anything

missing in the package, and contact your dealer of purchase to claim for

missing items:

PACKAGE CONTENTS:

Cautions:

1. Disconnect the device in thunderstorms in case of lightning damage.

2. Keep far from heat source and ensure ventilation.

3. Keep waterproof in the storage, transportation and operating environment.

QIG

Quick

Installation

Guide

Ethernet CableWiFi Repeater

A P Wireless Access Point

(AP: convert wired network to wireless network)

This Device can be used as a wireless AP, make your wired

network WiFi ready, your wireless devices can go internet

wirelessly via our repeater.

Client

(Client: convert wireless network to wired network)

Wired network devices (such as game console/computer), use

network cable connect the device through the CLIENT mode,

connect 2.4GHz wireless signal for Internet access.

Wireless Repeater

(Repeater: extend your existing wireless signal)

This Device connects to existing wireless network, and extends

wireless cover range.

Tips: Your root-wireless device can be scanned by this device,

and its signal strength should be no less than “ ”

Plug this device into socket, Power light should be constant on. WiFi LED always blinks, means the device starts to work.

Press WPS button of root-wireless device for 2seconds,

launch WPS function. (Please refer to your rooted wireless

device’s user manual for its WPS button usage)

The device’s WPS LED should be constant on, then means WPS connect successfully. (This WPS LED will turn off after 5 minutes)

In 2 minutes, press the WPS button of this device for 2seconds,

launch its WPS function. When WPS LED blinks, means

WPS is connecting.

ATTENTION: Above is only workable provided both of root-wireless device and this device have normally working WPS button. If

has no WPS button, please refer to “WiFi Repeater Web browser setup wizard”.

WPS

ADSL Router

Internet

Wireless Device

ADSL Router

Internet

Wireless Device

ADSL Router

Internet

Wired Device

Connect to a Network

Do you want to set up your network?

This is a new router that has not been set up. Click OK to start

setup.

Connect to the network without setting it up.

CancelO K

WiFi Repeater Web browser initial setup

Please check following

if need to change

working mode

1. Click “Start→Control Panel→Network and Internet→Network and SharingCenter→Change adapter settings→Wi-Fi(right click)→Properties”, Double click “Internet Protocol Version 4(TCP/IPv4)”.

2. To set up the computer IP 192.168.2.x (x arbitrary integer between 2~252), subnet mask of 255.255.255.0, Click “OK”. Back to the last interface and click “OK”. Then enter http://192.168.2.1

to configure.

Setup your computer’s IP after you finish configuration

1. Click “Start→Control Panel→Network and Internet→Network and Sharing Center→Change adapter settings→Wi-Fi(right click)→Properties”, Double click “Internet Protocol Version 4(TCP/IPv4)”

2. Select “Obtain an IP address automatically” and “Obtain DSN server address automatically”. Click “OK”. Back to the last interface and click “OK”. Then reconnect to repeater.

(If fails to connect network, Click “Start→Control Panel→Network and Internet→Network and SharingCenter→Change adapter settings→Wi-Fi(right click)→Properties→Diagnosis&Repair”;

Or please disconnect, and re-connect after 5 seconds.)

2 3

ATTENTION: Default SSID of this device is “current wireless network’s SSID+_2EX”, you can make clear whether your network is connected through this device;

Not connected

Connections are available

Wi-Fi

7inova-535060

7inova-535050

Connect automatically

7inova-521635

Open Network and Sharing Center

Information sent over this network might

be visible to others.

Connect

Setup your computer’s IP before connecting WiFi repeater

1) Restore Factory Setting: Plug the device into socket, press RESET button around 3-5seconds.

2) Default username: admin, Default password: admin (You can check on the label of device’s backside).

3) If get trouble in configure, fail to connect network, pls restore factory settings, then re-configure as per above steps.

Please use your PC, tablet or smart phone's wireless functions to search

for the device's SSID and connect.

Log in with Username and Password, both default are “admin”. Choose “Repeater”, click ”Apply”and then click “Search”. Select your wanted wireless network in the search list, enter the wireless network’s