A1 Touch SD17-PCAP Series Manuale utente
Rev.A
SD17-PCAP Series
Touch Screen LCD Monitors
USER’s GUIDE
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be reproduced,translated to another language
or stored in a retrieval system, or transmitted by any means, electronic, mechanical,
photocopying, recording, or otherwise, without prior written permission. Windows is a registered
trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective
holders.
The test results show that this device meets the FCC rules. Those limits are set to protect
residential areas from the devices with harmful emission. This device will produce, use and
radiate radio frequency energy. In addition, failure to follow the user’s manual to install or use
this device might produce harmful interference with radio communication. Not withstanding
the foregoing, it does not guarantee that this type of harmful interference does not occur in
some special installations. The interference caused by this device to the reception of radio
or television signals may be verified by turning it on and off. Any changes or modifications to
this TFT LCD would void the user’s authority to operate this device.
Important Recycle Instruction:
Lamp(s) inside this product contains mercury. This product may contain other
electronic waste that can be hazardous if not disposed of properly. Recycle or
dispose in accordance with local, state, or federal Laws. For more information,
contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific
disposal information check WWW.LAMPRECYCLE.ORG.
Table of Contents
Usage Notice
Precautions............................................................................................................................. 1
Introduction
About SD17-PCAP Series...................................................................................................... 2
Touch Screen for SD17-PCAP..... .......................................................................................... 3
Package Overview ................................................................................................................. 4
Installation
Product Overview ................................................................................................................... 5
Front View ........................................................................................................................ 5
Bottom View (Without Stand) ........................................................................................... 5
Kensington Security Slot ........................................................................................................ 6
VESA Mount for Your Monitor................................................................................................. 7
Start Your Installation.............................................................................................................. 8
Connecting the Display (Figure 10.1)..................................................................................... 9
(Figure 10.1).................................................................................................................... 10
Remove the Deskstand .........................................................................................................11
User Controls
Side Panel Controls.............................................................................................................. 12
How to Use the OSD Menus ................................................................................................ 13
On-Screen Display Menus.................................................................................................... 14
Appendix
Troubleshooting.................................................................................................................... 15
Warning Signal ..................................................................................................................... 16
No Signal .........................................................................................................................16
Going to Sleep................................................................................................................. 16
Out of Range ................................................................................................................... 16
Product Dimensions ............................................................................................................. 17
SD17-PCAP..... ............................................................................................................... 17
Compatibility Modes ............................................................................................................. 18
Touch Screen Driver Installation........................................................................................... 19
SD17-PCAP Driver Install Instructions............................................................................ 19
Usage Notice
! Warnin
g
- To prevent the risk o
f
fi
re or shock hazards, do not expose
this product to rain or moisture.
! Warnin
g
- Please do not open or disassemble the product as this ma
y
cause
e
l
ec
tri
c
s
h
oc
k.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to
maximize the life of your unit.
Do:
• Turn off the product before cleaning.
• Touch screen surface may be cleaned using a soft clean cloth moistened with mild window
glass commercial cleaners or 50/50 mixture of water and isopropylalcohol.
• Use a soft cloth moistened with mild detergent to clean the display housing.
• Disconnect the power plug from AC outlet if the product is not going to be used for an
extended period of time.
Don’t:
• Do not touch the LCD Display screen surface with sharp or hard objects.
• Do not use abrasive cleaners, waxes or solvents for your cleaning.
• Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
1
Introduction
About SD17-PCAP Series
The SD17-PCAP Series is a 17inch atpanel screen with an active matrix, thin- ilm
transistor (TFT) liquid crystal display (LCD).
Features include:
•Direct Analog signal input
•Active matrix TFT LCD technology
•1280 x 1024 SXGA resolution
•17" viewable display area
•31.47 ~ 80 KHz horizontal scan
•56 ~ 75 Hz high refresh rate
•0.264mm x 0.264mm pixel pitch
•Auto adjustment function
•Multilingual OSD user control
•Kensington security slot
•100 mm VESA mount
•Removable base for flexible mounting solutions.
•SD17-PCAP series Projected Capactive touch screen with USB controller
2
3
Touch Screen for SD17-PCAP
•Projected Capactive touch screen for
finger input only
•Surface: Glare treatment
•Interface: USB controller
•Transmittance: 90±5%
•HID: Windows® 7
•Driver: VISTA, XP, 2000, CE, XP Embedded, Linux, Apple® Mac OS
4
Package Overview
LCD Display Power Cord VGA Signal Cable
USB Cable ( A to B) Touch Driver CD
Cable Cover Screw
RS-232 Cable
(for combo model only)
Installation
Product Overview
• Front View
• Bottom View (Without Stand)
5
VGAAC IN USB
POWER SWITCH
Kensington Security Slot
The monitor can be secured to your desk or any other fixed object with Kensington lock
security products. The Kensington lock is not included.
6
VESA Mount for Your Monitor
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface
standard which defines a physical mounting interface for flat panel monitors, and
corresponding with the standards of flat panel monitor mounting devices, such as wall and
table arms. The VESA mounting interface is located on the back of your monitor.
To mount the monitor on an UL-listed certified swing arm or other mounting fixture, follow the
instructions included with the mounting fixture to be used.
! Warning!
Please select the proper screws!
The distance between the back cover surface and the bottom of the screw hole
is 11 mm. Please use four M4 screws diameter with proper length to mount
your monitor.
Please note: the mounting stand must be able to support at least 11 lbs ( 5Kg).
7
Slots (x4)
VESA
Mounting
Interface
100.0
100.0 110.4
Indice
Altri manuali A1 Touch Monitor
