AAxeon FCM-CHS2 Series Manuale utente
FCM-CHS2-XX
16-SLOT IN-BAND MANAGEMENT CHASSIS
User's Guide
Version 1.5
.
2
FCC Warning
This equipment has been tested and found to comply with the limits for a ClassA
digital device, pursuant to Part 15 of the FCC Rules. These limitations are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if no installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into a different outlet from that the receiver is
connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission
limits.
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance, could affect the user’s authority to operate the
equipment.
Aaxeon Technologies, Inc. has an on-going policy of upgrading its products and it
may be possible that information in this document is not up-to-date. Please visit
our website at www.aaxeon.com for the latest information. No part of this
document can be copied or reproduced in any form without written consent from
the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
3
Table of Contents
1. INTRODUCTION
1.1.In-Band Management Chassis - 4
1.2.Management Modules - 6
1.3.Redundant Power Supply - 7
1.4.Connectors, Indicators, and Switches - 7
2. INSTALLATION
2.1.Requirement - 9
2.2.Unpacking the In-Band Management Chassis - 9
2.3.Install slide-in modules -10
2.4.Install the In-Band Management Chassis -11
2.5.Connect slide-in modules to network -11
2.6.Connect redundant power supply (Optional) -12
2.7.Power on the In-Band Management Chassis -12
3. OPERATION
3.1.LED status -13
3.2.Console management -13
3.3.SNMP -13
4. MAINTENANCE -14
4.1.Fault identification -14
4.2.Hardware replacement procedures -15
4.3.Firmware upgrade -15
Appendix A. Technical Specifications -16
4
1. INTRODUCTION
The In-Band Management Chassis is the most versatile and cost effective
solution for multiple network media conversion. With a wide selection of slide-in
converter modules, the In-Band Management Chassis allows users to upgrade
and integrate their existing copper network to a fiber network.
1.1 In-Band Management Chassis
The 19-Inch rack mountable chassis is capable of serving up to 16 slide-in
converter modules. The system and each slide-in converter status can be
monitored through the built-in management module via SNMP. The In-Band
Management Chassis supports power redundancy by using a second power
supply.
Key Features
•Compact size, high density
19-inch rack mountable
Up to 16 slide-in converter modules
•Hot swappable converter modules and power supplies
•Chassis Power/FAN monitoring
•Local module monitoring - Model/Media/Link/Speed/Duplex/Activity
/Auto/Power State
•Remote module monitoring - Model/Media/Link/Speed/Duplex/Activity
/Auto/Power State
•Local modules enhanced monitor-Traffic Counter
•Local modules control –Auto/Speed/Duplex/Flow Control
•Remote modules control –Auto/Speed/Duplex/Flow Control/MDI/MDIX
•Local modules enhanced control – MDI/MDIX/Rate Limit/Broadcast Storm
•Local modules specifications - Fiber Type/Wave Length/Distance
5
•In-Band diagnostic (Loop-back test)
•TFTP/FTP Firmware upgrade
•4-level user account management
•Console/Telnet/SNMP management
•SNMP agent support
MIB II Interface (RFC 1213/1573)
Private MIB (CHASSIS2)
RMON MIB (RFC 1757)
•SNMP trap support:
Warm/Cold start
Authentication Fail
Local/Remote Link Up/Down
Power & Fan Fail
Remote Power Fail
Local Module Install/Remove
•Plug and play operation
•LED indication
Power (PRI/SEC/ACT), LAN, COM
•Optional redundant power supply
Support 2 hot-swappable power modules (AC100-240V or DC48V)
6
1.2 Management Module
The Management Module is located on the front-left of the In-Band Management
Chassis. The customer may use SNMP to monitor the system and installed slide-
in module status.
The In-Band Management Chassis can be monitored locally through the DB-9
console port or remotely through the RJ-45 10/100Base-T LAN port on the
Management Module.
NOTE: Please refer to the In-Band Management Chassis Network Management
Manual for detailed management functions.
7
1.3 Redundant Power Supply (Optional)
An optional redundant power supply can be ordered for non-stop running.
This is important when the In-Band Management Chassis is used in critical
applications.
NOTE: Please refer to Section 2.6 for Redundant Power Supply installation.
1.4 Connectors, Indicators, and Switches
Front Panel
LED
Power A Power A status
Power B Power B status
LAN 10/100Base-T activity status
COM Console port activity status
LAN Fully compliant with 802.310/100Base-T
RJ-45 STP/UTP connector
For SNMP application
COM DB-9 (DTE) connector
Console operation
For local management
Management Module
16 slots for
slide-in modules
LAN
LED
COM
8
Rear Panel
Power Switch and Connector
Switch On/Off primary power
PowerALED should turn on when this switch is on
Power B LED should turn on when Power Supply B is active
Connector AC power connection
100-240V, 50-60Hz, 150W
External Redundant Power Supply Connector
Connector Redundant power supply connection
SEC LED should turn on when connected
SEC ACT LED should turn on when active
FAN Air ventilation
Spins after powered on
Fans
Power Supply B
(Optional)
Power SupplyA
9
2. INSTALLATION
The procedures for installing the In-Band Management Chassis is as follows,
2.1 Requirement
2.2 Unpacking the In-Band Management Chassis
2.3 Install slide-in modules
2.4 Install the In-Band Management Chassis
2.5 Connect slide-in modules to network
2.6 Connect Redundant Power Supply (Optional)
2.7 Power on the In-Band Management Chassis
2.1 Requirement
The In-Band Management Chassis basic requirements for installation are as
follows.
•Environmental conditions.
-One power outlet for the In-Band Management Chassis internal
power supply
-One power outlet for a Redundant Power Supply (if ordered)
-Proper ventilation
-UTP cables should not run in the same duct as the power and
phone line cables
•Required fiber conversion slide-in modules
•Required Fiber and UTP cables
•Redundant Power Supply (optional)
•Rack mounting tools
2.2 Unpacking the In-Band Management Chassis
The following items should be checked after opening the shipping package.
1. In-Band Management Chassis
2. Power Cord
3. User’s Guide (CD-ROM)
4. Slide-In Converter Modules (optional)
5. Redundant Power Supply (optional)
10
2.3 Install Slide-In Modules
CAUTION
To prevent any Slide-In Module damage or failure, please wear a grounding
device and observe electrostatic discharge precautions before installing
into the In-Band Management Chassis.
Procedure
1. Plan the slide-in module slot position
-All slots are identical
-Slide-in module can be installed into any slot
2. Remove the protective plate from selected installation slot
3. Insert slide-in module carefully into the selected slot
-Make sure that the slide-in module is firmly connected with
the back plane connector.
4. Screw in modules.
5. Repeat steps 2 to 4 for all Slide-in modules.
Power Modules
Media
Conversion
Center
E-MCC-1600
Power
In Use
Power
In Use
1
2
Manage ment
Mo dule
Indice
