ABB 6153 EB-500 Manuale utente
ABB i-bus® EIB
Actuator 6153 EB-500
for lamp installation with
control output (0 - 10 V)
for electronic ballasts
Operating instructions
only for authorized, skilled electricians with
EIB training
73 - 1 - 5832
22013
Important instructions
Attention
It is absolutely essential that the EIB bus is installed
by an authorized electrician. Laying and connection of
bus line and applications devices must be effected in
conformity with valid regulations according to DIN -
VDE and the EIB manual of the ZVEI / ZVEH.
Connect the touch contact input to the same phase as
the device’s power supply.
For wiring of the actuator 6153 EB, the specifications
of the lamp / EVG manufacturer with regard to current
at make and power factor have to be observed.In some
cases it may be necessary to install a making current
limiter (e. g. 6515).
Notes
If the physical address has not yet been assigned, the
programming key (Fig.1, pos.5) should still be accessible.
If necessary, please install the lamp cover lateron. The
manufacturer database of Busch-Jaeger is continuously
updated. It stores the latest types of applications and their
related descriptions. If this database is not available to
you, please send for a copy.
Technical data / Connection
EIB connection
Nominal voltage: 24 V
Current consumption: < 10 mA
Switching connection
Nominal voltage: 230V - 50 Hz
Switching current: 10 A, cos ϕ0.6
Touch contact input: 230 V, 50 Hz
Line length of the touch
contact input: max. 100 m (unlighted)
Control voltage: 0 - 10 V
Control current: up to 50 mA
Operating temperature: -5 to +45 °C
Protection type: IP 20
←o switched phase (lamp)
→o phase (lamp)
L o phase (voltage supply)
N o neutral conductor
1 o touch contact input
+ o control voltage 0-10 V (EVG)
– o control voltage 0-10 V (EVG)
12 76453
+
–
Installation / Fig. 1
Switch off supply voltage !
Remove both outer caps from the device. The device is
fixed in the lamps by means of screws put through the
long holes (cf. Fig. 1 below, positions 1; 7 ).
The connection of supply voltage and control line is effected
at the 7-pin terminal block (pos. 2). Please observe the
connection information given in the „technical data“
section. When the bus voltage is missing, and a 230 V
voltage supplied, the actuator 6153 EB will auto-
matically switch on (working illumination).
The connection to the EIB bus is made by means of a 2-
pin bus terminal (item no. 6183) which is plugged into the
entrance (pos. 6). Please make sure that the polarity of
terminals is correct (red = +, grey = -).
Adapt bus coupling process
Assign physical address
• Connect a PC equipped with the EIBA software (ETS)
to the EIB bus line via an EIB-RS 232 interface.
• Press the programming key (pos. 5) at the actuator:
the red programming LED (pos. 4) will become
illuminated.
• After the physical address has been programmed,
the red LED will go out.
• Write the number of the physical address on the
device using a smudge-proof pencil (df. Fig. 1, pos. 3).
Assign group address(es)
• Group addresses are assigned via a PC in connection
with the ETS software.
Select application
Open the device window and choose the desired
application version. At present, there are two versions
available.
Adapt bus coupling process
Alternative application
Version 1
This device offers the following functions:
• Switching of lamps on-site via several conventional
touch contacts (e. g. 2020 US without lighting).
• Dimming of lamps with electronic ballasts (0-10 V
control input) via EIB sensors (e. g. 6118xx).
• Calling of two freely definable brightness values
(presets) for lamps with electronic ballasts (0 - 10 V
control input)
- via EIB sensors (e. g. 6117xx).
You may differentiate this version of the actuator 6153 EB
by using the „parameters“ option of your ETS software:
• ON:
- last brightness setting (memory) or
- minimum brightness (basic brightness) or
- maximum brightness
• Dimming speed
- time for one run of the light (0 -100 %) in seconds.
• Preset 1 or 2, resp.
- these values are freely selectable via percentage
inputs.
Adapt bus coupling process
Version 2
This device may be used as a pure switching actuator.
Then, its contact time behavior may be adjusted via the
„parameters“ option (e. g. staircase lighting time-switch).
Indice
Altri manuali ABB Controllori
ABB
ABB DOL Starter Manuale utente
ABB
ABB Totalflow mflo Series Guida utente
ABB
ABB ACS 800 Series Manuale utente
ABB
ABB ISL-A 24 Manuale utente
ABB
ABB DSQC1016 Manuale utente
ABB
ABB Series Manuale utente
ABB
ABB COM600 4.0 Manuale utente
ABB
ABB ACS310 Manuale utente
ABB
ABB RMC-100 Guida utente
ABB
ABB NextMove e100 Manuale utente
ABB
ABB ACS320 series Manuale utente
ABB
ABB PSTX Series Guida
ABB
ABB AC500-eCo Series Manuale di riferimento
ABB
ABB 07CR41 Manuale utente
ABB
ABB ACS550 Series Manuale utente
ABB
ABB MS116 Manuale utente
ABB
ABB DCS880 H1 Manuale utente
ABB
ABB PST30 Manuale
ABB
ABB Advant Controller 450 Manuale utente
ABB
ABB PLUTO Safety-PLC Manuale utente
