ABB SPACOM 300 Manuale utente
—
Relay Retrofit Program
Cutting Tool
Operating Guide SPACOM 300
RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300 3
—
1. Preparations
Remove the existing relay.
Ensure that there is enough space to operate
the cutting tool in all intended directions.
Check the space required by the replacement
IED and its wiring.
Place the cover plate in its intended location.
Mark the outline for the opening and the fixing screw
locations in each corner of the cover plate.
Drill the holes for fixing screws using a drill bit
of 4.5 mm in diameter.
1.1
1.2
—
2. Cutting cycle
Horizontal: 1, 4, 3 and 2.
Min. 171
214
139
4RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300
—
3. Operating the cutting tool on a horizontal edge
Ensure that the cutting head is set in the correct
position. The text HORIZONTAL Up and Down must
point in the direction you are cutting.
Make four punches, side by side.
Ensure that you use the correct guiding,
before each cutting cycle.
After each cutting cycle, ensure that thecutting head
is clear of offcut!
3.1
3.2
3.3
RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300 5
Push the vent lever to release the punch
after each cutting cycle.
For your safety, keep your hands on the power unit,
never on the cutting head.
Beware of the sharp edges!
Note the cutting order. Cut the parts next to
the edges first and the middle part last.
3.4
3.5
3.6
6RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300
—
5. Finishing your work
Finish your work and install the new IED.
Clean the offcuts from the floors.
5.1
—
4. Install the cover plate
Close the door and install the cover plate.
Use the self-tapping screws supplied with
the cover plate.
4.1
7
—
Notes
1MRS757999 REV C EN 3-2019
© Copyright 2019 ABB. All rights reserved.
Specifications subject to change without notice.
Additional information
We reserve the right to make technical changes or
modify the contents of this document without prior
notice. With regard to purchase orders, the agreed
particulars shall prevail. ABB does not accept any
responsibility whatsoever for potential errors or
possible lack of information in this document.
We reserve all rights in this document and in the
subject matter and illustrations contained therein.
Any reproduction, disclosure to third parties or
utilization of its contents – in whole or in parts – is
forbidden without prior written consent of ABB.
—
For more information, please contact
E-Mail: af[email protected]
abb.com/service
abb.com/mediumvoltage
Indice
Altri manuali ABB Staffetta
ABB
ABB OREL-01 Manuale utente
ABB
ABB CL-LSR Series Manuale
ABB
ABB Relion 615 series Manuale utente
ABB
ABB REU 513 Manuale utente
ABB
ABB REL-300 Manuale utente
ABB
ABB Relion 615 series Manuale utente
ABB
ABB RELION 650 SERIES Guida rapida
ABB
ABB KLF Series Manuale
ABB
ABB 41-331.21 Manuale
ABB
ABB CM-MSS.12 Manuale utente
ABB
ABB CM-ESS.1 Manuale utente
ABB
ABB CM-UFD.M22 Manuale utente
ABB
ABB REU615 Manuale utente
ABB
ABB REL-300 Manuale
ABB
ABB SC Manuale
ABB
ABB Busch-Wachter 6812U-101-500 Manuale utente
ABB
ABB TRB Series Manuale
ABB
ABB Relion 630 Series Manuale utente
ABB
ABB RELION Series Manuale di installazione e funzionamento
ABB
ABB SPAD 330 C Manuale utente
