ABC Office Vector 06502 Manuale utente

VECTOR

KT7105-A

06502

Shoplifting Protection

Ketec, Inc

abcoffice

www.abcoffice.com

1-800-658-8788

VECTOR USERS GUIDE

INDEX

Parts List …………………………….1

Assembly Instructions………………2

Positioning the System …………….3

Tagging Guidelines …………………4

Removing Hard Tag……………….. 7

Detection Area ……………………...9

Alarm Handling ……………………..10

Troubleshooting …………………….11

Warranty……………………………..Back Cover

abcoffice

www.abcoffice.com

1-800-658-8788

Remove all contents from packaging. Compare products with the example. If you

are missing any parts please contact your supplier immediately. The carton should

contain:

VECTOR ANTENNA WITH WIRE BASEPLATE

CAP NUTS AND WASHERS

5’ RUBBER MOLDING &

DOUBLE SIDED TAPE

POWER SUPPLY WITH 10’ OF

CORD

PARTS LIST

abcoffice

www.abcoffice.com

1-800-658-8788

ASSEMBLY INSTRUCTIONS

1. Locate the baseplate, cap nuts

and washers.

2. Place the antenna on top of

the baseplate, aligning the

holes in the antenna base with

the studs on the baseplate.

Make sure that the power

supply wire is in the channels

of the antenna base and is not

crushed between the antenna

base and the baseplate.

3. Attach the washers and cap

nuts to the bolts on the

baseplate. DO NOT TIGHTEN.

4. Again make sure that the

power wire is not crushed

between the antenna base and

baseplate and tighten the cap

nuts with a ½” wrench.

5. Connect the wire on the power

supply to the power wire

connected to the antenna. The

wires will only connect in one

direction.

abcoffice

www.abcoffice.com

1-800-658-8788

POSITIONING THE SYSTEM

6. Position the system a

minimum of 18” (Inches) from

the doorframe and on the side

closest to the door handle.

7. Cut the rubber molding to the

length that will allow it to cover

the wire from the wall to the

system. You must cover the

wire, using a metal pancake

molding If the wire is in an

area where it will be walked

upon.

8. Insert the system power wire

into the rubber pancake

molding through the slit on the

back. Using double sided tape

fasten the rubber molding to

the floor.

9. Plug the power supply into the

closest outlet. We do not

recommend using an

extension cord for the system.

10.Test the system by placing

one of the hard tags into the

system. The system will beep

approximately 1-1/2 seconds

then reset. If a hard tag is held

in the system it will continue to

alarm. 18 Inches

Minimum

abcoffice

www.abcoffice.com

1-800-658-8788

TAGGING GUIDELINES

1. The tag should be visible to

the customer.

2. Tag uniformly, it speeds up

removal.

3. Tag near a price label. It

assists in the removal.

4. Place the tag as high as

possible when tagging silks &

light or stretchy fabrics.

5. Except for leather goods we d

not recommend locating the

tag at the seams. The seams

are easily cut open to remove

the pin.

6. Avoid placing tags on

waistbands, cuffs, hems or

perimeters. They can be easily

cut off.

7. Insert pins through the

garment then gently push into

the tag.

8. Never force the pin into the

tag.

9. Never use bent pins.

Shirts/Blouses/Jackets

Skirts

abcoffice

www.abcoffice.com

1-800-658-8788

TAGGING GUIDELINES

Dresses Pants

One Piece Bathing Suit

Bikini Bathing Suit

abcoffice

www.abcoffice.com

1-800-658-8788

TAGGING GUIDELINES

Shoes Tennis Shoes

Belts Purses

abcoffice

www.abcoffice.com

1-800-658-8788

3. Remove the pin and hard tag

from the detacher and store for

future use.

2. Remove the pin by holding the

hard tag to the detacher and

pulling straight up on the pin or

garment.

1. Place the hard tag into the

detacher with the pin facing

up.

REMOVING HARD TAG

abcoffice

www.abcoffice.com

1-800-658-8788

REMOVING HARD TAG

It is possible for the locking mechanism to become jammed when the pin is pulled

extremely hard. It is possible to un-jam the pin so that you will be able to remove it

when needed.

The first step is to place the hard tag into the detacher then press on the head of the

pin. This should release the pressure on the locks allowing you to remove the pin.

If you are still unable to release the pin you can tap the locking mechanism (raised

area) on the corner of the sales counter, then put the hard tag back into the

detacher. The pin should now release.

THIS SPACE INTENTIONALLY LEFT BLANK

abcoffice

www.abcoffice.com

1-800-658-8788

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ABC Office Sistema di sicurezza

ABC Office

ABC Office 24501 Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente