Abicor Binzel SI4 Series Manuale utente

TECHNOLOGY FOR THE WELDER’S WORLD.

www.binzel-abicor.com

ABICOR BINZEL Corporation

650 Medimmune Court, Suite 110

Frederick, MD 21703

Phone: (301) 846-4196

Fax: (301) 846-4497

ABIROB W Liner Instructions

SI4-XXX Series Liners

LINCOLN DIRECT TORCHES

1. Position the torch cable as straight as possible.

2. With the torch neck and consumables ﬁtted, insert the liner into the rear of the torch until it bottoms in the tip

holder/tip or wire-brake if ﬁtted.

3. At the rear end of the torch measure the distance from the feeder plug to the end of the liner collet (Fig. 1). This is

dimension “X”.

4. Remove the liner from the torch and remove the dimension “X” from the front end of the liner (Fig. 2).

5. At the rear end of the liner, you must trim the excess liner which protrudes from the liner collet. Measure 4mm

past the collet and cut the excess oﬀ (Fig. 3). Note: When cut properly the liner should be ﬂush to 1mm recessed in

the liner nut.

6. Apply O-ring grease. Install the liner into the torch and tighten the liner retention nut (Fig. 4).

Fig. 1

Fig. 2

Fig. 3

Fig. 4

liner liner collet

4mm

liner retention nut

cut

Feeder plug

(Miller Direct Torches

on back...)

TECHNOLOGY FOR THE WELDER’S WORLD.

www.binzel-abicor.com

ABICOR BINZEL Corporation

650 Medimmune Court, Suite 110

Frederick, MD 21703

Phone: (301) 846-4196

Fax: (301) 846-4497

ABIROB W Liner Instructions

SI4-XXX Series Liners

MILLER DIRECT TORCHES

1. Position the torch cable as straight as possible.

2. With the torch neck and consumables ﬁtted, insert the liner into the rear of the torch until it bottoms in the tip

holder/tip or wire-brake if ﬁtted.

3. At the rear end of the torch measure the distance from the feeder plug to the end of the liner collet (Fig. 1) and

subtract 5mm. This is dimension “X”.

4. Remove the liner from the torch and remove the dimension “X” from the front end of the liner (Fig. 2).

5. At the rear end of the liner, you must trim the excess liner which protrudes from the liner collet. Measure 7mm

past the collet and cut the excess oﬀ (Fig. 3). Note: When cut properly the liner should protrude from the liner collet

by approximately 2mm or two coils.

6. Apply O-ring grease. Install the liner into the torch and tighten the liner retention nut (Fig. 4).

Fig. 1

Fig. 2

Fig. 3

Fig. 4

liner liner collet

7mm

liner retention nut

cut

2mm

(L - 5mm = X)

Feeder plug

(Lincoln Direct Torches

on back...)

Questo manuale è adatto per i seguenti modelli

Altri manuali Abicor Binzel Sistema di saldatura

Abicor Binzel

Abicor Binzel MIG Manuale utente

Abicor Binzel

Abicor Binzel TIG ABITIG MT Manuale utente

Abicor Binzel

Abicor Binzel iMIG POWER 400 Manuale utente

Abicor Binzel

Abicor Binzel MFS-V3 M-Drive Manuale utente

Abicor Binzel

Abicor Binzel ROBO WH 654 Manuale utente

Abicor Binzel

Abicor Binzel ABIROD G350 Manuale utente

Abicor Binzel

Abicor Binzel ABIMIG A155 Manuale utente

Abicor Binzel

Abicor Binzel iROB 401 AC/DC Manuale utente

Abicor Binzel

Abicor Binzel ABICOOLER 2000 advanced Manuale utente

Abicor Binzel

Abicor Binzel ABITIG GRIP 150 2 Manuale utente

Abicor Binzel

Abicor Binzel ABIROB A360 Manuale utente

Abicor Binzel

Abicor Binzel ABIROB A Series Manuale utente

Abicor Binzel

Abicor Binzel iROB 501 Manuale utente

Abicor Binzel

Abicor Binzel ABIMIG GRIP W Series Manuale utente

Abicor Binzel

Abicor Binzel ABI-CAR E-1200 Manuale utente

Abicor Binzel

Abicor Binzel ABICAR ADVANCED 42V Manuale utente

Abicor Binzel

Abicor Binzel ABICAR ADVANCED Manuale utente

Abicor Binzel

Abicor Binzel MT 452 W Manuale utente

Abicor Binzel

Abicor Binzel ABIPLAS CUT 200 W/MT Manuale utente

Abicor Binzel

Abicor Binzel xFUME ADVANCED HP 230V-CSA Manuale utente

Abicor Binzel

Abicor Binzel iROB 420 Manuale utente

Abicor Binzel

Abicor Binzel ALPHA FLUX 350 Manuale utente

Abicor Binzel

Abicor Binzel ABIROB W Manuale utente

Abicor Binzel

Abicor Binzel AB20 Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

ESAB

ESAB Buddy Arc 145 Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente