Abilia IRZ-REC4 Manuale utente
Rev D GB
Manual
How to program Control Omni with Andromeda
IRZ-REC4, Andromeda Socket, Schneider Radio
Pushbutton, Schneider Binary Adapter and
Schneider DimmerAdapter
2
Content
1Introduction................................................................................................ 4
1.1Different steps...................................................................................... 4
2Before starting........................................................................................... 5
2.1Important issues .................................................................................. 5
2.2Reset Andromeda IRZ-REC4.............................................................. 5
2.3Reset Schneider Radio Push Button................................................... 6
2.4Reset Andromeda Socket.................................................................... 6
2.5Reset Schneider Binary Adapter and Schneider Dimmer Adapter...... 6
3Include all units to the Control Omni library............................................... 7
3.1Include Gewa Andromeda IRZ-REC4.................................................. 7
3.2Include Andromeda Socket.................................................................. 8
3.3Include Schneider Binary Adapter....................................................... 9
3.4Include Schneider Dimmer Adapter................................................... 10
3.5Include Schneider Radio Push Button............................................... 11
4Set functions on a page in Control Omni................................................. 12
4.1Controlling an Andromeda receiver IRZ-REC4.................................. 12
4.2Controlling an Alert function in combination with Andromeda receiver
IRZ-REC4................................................................................................... 15
4.3Controlling an Andromeda Socket..................................................... 17
4.4Controlling a Schneider Binary Adapter............................................. 19
4.5Controlling a Schneider Dimmer Adapter.......................................... 21
5Associate the Schneider Radio Push Button (double switch).................. 23
3
4
1 Introduction
This instruction shows how to program Control Omni, Z-wave transmitters
and receivers and make a network of them.
1.1 Different steps
1. Reset units
2. Include all units to Control Omni
3. Set functions on a Control Omni page
4. Associate other Z-wave transmitters
Control Omni
Gewa Andromeda
IRZ-REC4 Schneider
Binary Adapter
and Dimmer
Adapter
Schneider Radio
Push Button
Andromeda
Socket
5
2 Before starting
2.1 Important issues
It is important to reset all the units before starting. See below how to do
this.
Warning: Please make sure that the Schneider Radio Push Button is
ALWAYS idle before starting a step. If not, you can get undefined
behavior. You see that it is idle by looking at all LEDs, the one in this
manual has 2 LEDs. They both should be unlit. That is, not green or
red.
Control Omni must always be a Master unit, which means that all units
must be included in the Control Omni library.
The relay units must be connected to power.
2.2 Reset Andromeda IRZ-REC4
Press the button
Setting Press the button
GR-Units Press the button
Exclude GR-Unit Press the button
Exclude GR-Unit
6
2.3 Reset Schneider Radio Push Button
Do exactly the same as in section 2.2 but press one of the
buttons 3 times. Be very distinct and do it quick.
2.4 Reset Andromeda Socket
Do exactly the same as in section 2.2 but press the
programming area 3 times. Note the red arrow. Be very distinct
and do it quick.
2.5 Reset Schneider Binary Adapter and Schneider
Dimmer Adapter
Do exactly the same as in section 2.2 but press the
programming area 3 times. Note the red arrow. Be very distinct
and do it quick.
Press 3 times on
the programming
button. Be very
distinct and do it
quick. The relay in
Andromeda will
click 3 times when
success.
Press the button
as next picture
7
3 Include all units to the Control Omni library
Control Omni must work as a master unit, which means that all units in the
network must be included in the Control Omni library.
3.1 Include Gewa Andromeda IRZ-REC4
Name the unit and
press the green
s
y
mbo
l
. Read
y
!
Press 3 times on
the programming
button
Press the button
Setting Press the button
GR-Units Press the button
Include GR-Unit Press the button
as next picture
8
3.2 Include Andromeda Socket
Name the unit and
press the green
symbol. Ready!
Press the button
Setting Press the button
GR-Units Press the button
Include GR-Unit Press the button
as next picture
Press 3 times on
the programming
area.
9
3.3 Include Schneider Binary Adapter
Name the unit and
press the green
symbol. Ready!
Press 3 times on
the programming
area.
Press the button
Setting Press the button
GR-Units Press the button
Include GR-Unit Press the button
as next picture
10
3.4 Include Schneider Dimmer Adapter
Name the unit and
press the green
symbol. Ready!
Press 3 times on
the programming
button
Press the button
Setting Press the button
GR-Units Press the button
Include GR-Unit Press the button
as next picture
Indice
