ABK AXT8921A Manuale utente
IP Voice Intercom Terminal AXT8921A AXT8921B
AXT8921A AXT8921B
User Manual
Thank you for using our product. Please read this User Manual carefully to make better use
of this equipment.
http://www.abk-pa.com
This page is left blank for the user’s notes.
About this User Manual
This User Manual is available and effective upon completion of development of
AXT8921 IP Intercom Terminal. The User Manual includes system description,
matters needing attentions in use, instructions on system connection, instructions
on use of product and technical specifications of the terminal. Please read this
User Manual carefully before connection, installation and use and operate in
accordance with corresponding instructions in the Manual.
This symbol on the rear panel indicates matters needing attentions, please
use or operate the product in accordance with corresponding instructions.
Please keep this User Manual in good custody for future use.
Facture 2021-4-27
Matters Needing Attention
Please read the following before operating the product.
Warning
The following basic requirements must be strictly observed, to avoid potential personal injury and equipment or
property damages to you or any person nearby. The basic requirements include without limitation to the following:
Power Source/Power Cable
• Please disconnect the device from power source
by pulling the plug other than the power cord.
Pulling the power cord may result in damages.
• Please keep the power cord away from heat source.
Do not over-bend the power cord or place it
anywhere it can be stepped on or may cause to trip.
• This is connected to power source via the plug and
any failure or danger occurs, the user can
disconnect the device from power source by pulling
out the plug out from the socket, therefore, it is
required that the power socket should be located
somewhere with easy access.
• The device is not completely disconnected from
power source when it is switched "OFF". For sake
of safety, please disconnect the device from the
socket if it is not in user.
Positioning
• Please disconnect the device from power source
before relocating the device.
• For avoiding deformation of panels and damages
to internal components, please do NOT place the
device where there is heavy dust or violent
vibration, or where it is extremely cold or hot.
• Please keep this device off water drops or splash
or vase filled with water or any other articles of
similar nature.
Connection
• Please disconnect other equipment from power
source before they are connected to this product.
Please tune volume to its minimum level before the
device is powered ON or OFF.
• All terminals on the device marked with are
live and dangerous, and should be connected by
trained personnel.
When abnormal conditions are realized
• Please disconnect the device from power source
immediately in case the power cord is worn or
damaged or if the sound is suddenly cut off or any
abnormal odor or smoke comes out from the device,
and then have the device inspected and repaired by
professional personnel.
Precautions in Operation
• Please do NOT insert any finger into any gap or
opening of the device.
• Please prevent foreign objects (paper, plastics or
metal etc.) from being inserted or falling into any
gap or opening of the device. In such case, please
cut off power source immediately.
• Please do NOT put the body or any heavy object
on the device and do NOT operate the buttons or
switches or connections with excessive force.
Do NOT Open
• Please do NOT remove the cover of the equipment,
otherwise you may get an electric shock.
• Do NOT attempt to remove any internal
component from the device, or to modify the
equipment in whatever manner. In case of any
abnormal condition, please stop using the device
immediately and have it inspected and repaired by
professional personnel.
Other Precautions
• Our company shall not be responsible for data loss
or damages due to improper use of unauthorized
modification to the device.
• The images and screen display in this Manual are
only for description and may be different from
screen images in actual operation. The screen
display depends on the product.
i
CONTENTS
I. Product Description.......................................................................................... 1
1.1 Appearance Description................................................................................. 1
1.2 Features.......................................................................................................... 1
II. Operating Instructions..................................................................................... 3
2.1 Connect the Power Supply and the Network................................................. 3
(1) Connect the Network......................................................................3
(2) Interface Description...................................................................... 4
III. Basic Operations............................................................................................ 9
3.1 Answer a Call................................................................................................. 9
3.2 Make a Call.................................................................................................... 9
3.3 End a Call....................................................................................................... 9
3.4 Call Records................................................................................................... 9
IV. Page Settings................................................................................................ 10
4.1 Browser Configuration.................................................................................10
4.2 Preset Password............................................................................................10
4.3 WEB Page.................................................................................................... 10
(1) Basic Settings............................................................................... 10
(2) Network Settings.......................................................................... 12
(3) VOIP.............................................................................................13
(4) Intercom Settings..........................................................................15
(5) Security Settings...........................................................................20
(6) Management Settings................................................................... 22
(7) Video (Only for Video Intercom Terminal)..................................24
V. Appendix........................................................................................................ 30
5.1 Technical Parameters....................................................................................30
1
I. Product Description
This product is a fully digital network intercom equipment, with mature VOIP solution for
its core part, stable and reliable, and the digital full duplex for hands-free device, loud and
clear. It is durable and simple to install with comfortable buttons, generous appearance and
low power consumption.
1.1 Appearance Description
AXT8921A AXT8921B
Button Description
1.2 Features
2 SIP lines.
Full-duplex hands-free calling.
Editable call button (one-key call, intercom key, etc.).
Wall-mounted installation.
Button
Description
Function
The shortcut button
can be edited.
It can be set to various functions to meet the
needs of different occasions.
Speaker
Service button
MIC
Call button
(Editable)
2
Built-in 2 short-circuit inputs.
Built-in 2 short-circuit outputs. 4 controlled methods: remote DTMF, remote service
command, short-circuit input linkage and call status.
External active speaker output interface.
Support POE power supply.
With multicast function.
Three functions in one: intercom, broadcast and smart security.
In compliance with IP54.
3
II. Operating Instructions
Before you start to use the device, please make the following installation.
2.1 Connect the Power Supply and the Network
Note! As this device can support POE power supply, please connect it via a router with POE
power supply.
(1) Connect the Network
In prior to this step, please check if your network can work normally with broadband
internet access.
Broadband Router
Connect one end of the network cable to the WAN port of the IP voice intercom, and the
other end to the LAN port of your broadband router to complete the network hardware
connection. In most cases, you must configure your network settings of the IP voice
intercom to DHCP mode. Please refer to 4.3 (2) Network Settings for detailed setting ways.
No Broadband Router
Connect one end of the network cable to the WAN port of the IP voice intercom, the other
end to the LAN port of your broadband modem to complete the network hardware
connection. In most cases, if you are using a TV cable broadband, you must configure your
network settings of the IP voice intercom to DHCP mode; if you are using the ADSL, you
must configure your network settings to PPPoE mode. Please refer to 4.3 (2) Network
Settings for detailed setting ways.
4
(2) Interface Description
a. Connection Diagram of Network PA Intercom
5
b. Connection Diagram of Peripherals
c. Main Board Interface
1: WAN
9: LINE
OUT
2: LAN
10: LINE
IN
11: 12V
DC
7: IP PA
Button
3: 2 Short
Circuit IN
6: Restore
Button
4: 2 Short
Circuit
OUT
12: Built-in
Speaker
5: 2 Call
Buttons
8: MIC
Questo manuale è adatto per i seguenti modelli
1
Indice
