Aboundi APL1400-200 Manuale utente
APL1400-200 User’s Manual 1
Version 1.1
APL
APLAPL
APL1
11
14
44
400
0000
00-
--
-200
200200
200
UltraSpeed
TM
PowerLine Quad
Ethernet NetBridge
™
User’s Manual
Version 1.1
APL1400-200 User’s Manual 2
Version 1.1
1. Please read all instructions before installing and operating APL1400-200 and keep all
instructions for later reference.
2. Please follow all warnings and instructions marked on the product.
3. Unplug the AC coupler from the wall outlet before cleaning. Use a damp cloth for
cleaning. DO NOT use liquid cleaners or aerosol cleaners.
4. DO NOT operate APL1400-200 near water.
5. APL1400-200 should never be placed near or over a radiator, or heat register.
6. APL1400-200 relies on the building’s electrical installation for short-circuit (over current)
protection.
7. Ensure that a fuse or circuit breaker no larger than 120 VAC 15A or 240 VAC 6A is used on
the phase conductors (all current-carrying conductors).
8. DO NOT allow anything to rest on the APL1400-200 interconnect cables. DO NOT locate
APL1400-200 where people may walk on the cables.
9. APL1400-200 has its own power filter for protection against surges.
10. APL1400-200 is NOT field serviceable and should not be opened under any circumstance.
Opening or removing covers may result in exposure to dangerous voltage points or other risks.
11. Unplug the AC coupler from the wall outlet and refer the product to qualified service
personnel for the following conditions:
When the interconnect cords are damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate normally when the operating instructions are followed.
If the product exhibits a distinct change in performance.
I
MPORTANT
S
AFETY
I
NSTRUCTIONS
APL1400-200 User’s Manual 3
Version 1.1
Copyright © 2009 by Aboundi Inc. All rights reserved.
No part of this documentation may be reproduced in any form or by any means or used to make any
derivative work (such as translation, transformation, or adaptation) without written permission from
the copyright owner.
All the other trademarks and registered trademarks are the property of their respective owners.
Statement of Conditions
The content described in this manual may be improved or changed at any time and it is subject to be
changed without notice.
Manufacturer assumes no responsibility for errors contained herein or for direct, indirect, special,
incidental or consequential damages with the furnishing, performance, or use of this manual or
equipment supplied with it, even if manufacturer of its suppliers have been advised of the
possibility of such damages.
Electronic Emission Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device will accept any interference received, including interference that may cause
undesired operation.
APL1400-200 User’s Manual 4
Version 1.1
Table of Content
1.
Introduction ..........................................................................................................5
1.1. Features............................................................................................................................5
1.2. Product Kit .......................................................................................................................6
1.3. LED..................................................................................................................................6
1.4. Hardware Installation........................................................................................................7
1.5. Application.......................................................................................................................8
1.5.1. Multiple Connections With APL1400................................................................................8
1.5.2. Front Counter Multiple Connections with APL1400........................................................ 10
2.
Software Installation...........................................................................................12
2.1. System Requirements......................................................................................................12
2.2. Installation...................................................................................................................... 12
3.
Web Configuration..............................................................................................15
3.1. Start-up and Log in .........................................................................................................15
3.2. Connection Info .............................................................................................................. 16
3.3. Configuration.................................................................................................................. 17
3.3.1. Security Page.................................................................................................................. 18
3.3.2. Network Page .................................................................................................................19
3.3.3. VLAN Page.................................................................................................................... 20
3.3.4. QoS Page........................................................................................................................21
3.4. Change Password............................................................................................................22
3.5. Firmware Upgrade.......................................................................................................... 23
3.6. Factory Reset.................................................................................................................. 24
3.7. Reboot............................................................................................................................ 25
4.
Default Settings ..................................................................................................25
APL1400-200 User’s Manual 5
Version 1.1
1. Introduction
The Aboundi APL1400-200 UltraSpeed
™
Series PowerLine Quad Ethernet NetBridge
™
allows the
Plug-and-Play simplicity utilizing the existing electrical wiring facility as the network infrastructure
connections.
The APL1400-200 enables IP Cameras, Video Servers, POS, Media Converters, Printers, Digital
Signages and Network Equipments for easy broadband access in a tight cluster space. The
APL1400-200 NetBridge
™
can be quickly installed for commercial applications require high
bandwidth and critical demand of reliable network connection (QOS). The networking group can be
easily reallocated without the need to rewire “home run” Ethernet drops to such cluster group
locations.
The APL1400-200 NetBridge
™
is designed specifically for small cluster networking applications
by providing four MDI/MDIX auto detection RJ-45 ports that can connect to any 10/100Mbps
Ethernet ports on the computer and other peripheral devices.
1.1. Features
Four shielded RJ-45 MDI/MDIX auto detection Ethernet ports
Up to 200Mbps speed over the standard facility electrical power lines
Integrated Quality of Service (QOS) allows reliable triple play applications
Transparent to facility circuit breakers
Simple Plug-and-Play installation
Supports up to sixteen APL1400-200 devices on one network domain
168-bit Tri-DES encryption for secure data transmission
Network segmentation through network identifier
Ident-and-Connect
™
™™
™
feature allows ease of network scan and network segmentation
Web based configuration
Up to 300 meters of operational distance
Compliance with IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX , UPA
APL1400-200 User’s Manual 6
Version 1.1
1.2. Product Kit
Before starting installation, please make sure the APL1400-200 package includes the following five
items:
1) Quick Installation Guide
2) APL1400-200 unit
3) CD-ROM (containing Ultra NetBridge
™
Utility for Windows and User’s Manual).
4) Cat 5e cable
5) Power cord
If anything from the above items is missing, please contact your vendor.
1.3. LED
The following figure shows the APL1400-200 LED indicator.
The function for each LED is described as follow:
PWR-Green: On when the power is on.
LNK/ACT-Blue: On when PowerLine Link speed over 12Mbps,
Purple: On when PowerLine Link speed between 12Mbps and 6 Mbps,
Amber: On when PowerLine Link speed under 6Mbps,
Blinking when PowerLine activity is detected.
LNK/ACT-Green: On when Ethernet link is detected;
Blinking when Ethernet activity is detected.
APL1400-200 User’s Manual 7
Version 1.1
1.4. Hardware Installation
Step 1 Plug the included Ethernet network cable into the computer’s Ethernet port.
Step 2 Plug the other end of this cable into the Ethernet port of APL1400-200.
Step 3 Plug the electrical cable into to the electrical port of APL1400-200.
Step 4 Plug the power plug into the AC socket on the wall.
APL1400-200 User’s Manual 8
Version 1.1
1.5. Application
Example – POS/Retail Application
Electric Connect
○
○○
○
R
allows the Plug-and-Play simplicity utilizing the existing electrical wiring
facility as the network infrastructure connections. Your data collected from the POS will send back
to the computers in the back office of the stores. Below is a typical POS Application Diagram.
1.5.1.Multiple Connections With APL1400
The APL1400-200 NetBridge™ is designed specifically for small cluster networking applications
by providing four MDI/MDIX auto detection RJ-45 ports that can connect to any 10/100Mbps
Ethernet ports on the computer and other peripheral devices.
APL1400-200 User’s Manual 9
Version 1.1
Step 1 Plug the included Ethernet CAT5 cable into the computer’s Ethernet port.
Step 2 Plug the other end of the CAT5 cable into the Ethernet port onAPL1400.
Step 3 Repeat the Step 1 to Step 2 for the rest of computers you want to connect to Electric
Connect
○
R
networks.
Step 4 Plug the power cable into the power port on the APL1400.
Step 5 Plug the power plug into the AC socket on the wall.
APL1400-200 User’s Manual 10
Version 1.1
1.5.2.Front Counter Multiple Connections with APL1400
Step 1 Plug the included Ethernet network cable into the credit card terminal’s Ethernet
port.
Step 2 Plug the other end of this cable into the Ethernet port of APL1400.
Step 3 Repeat the Step 1 to Step 2 for the rest of computers you want to connect to Electric
Connect
○
R
networks.
Step 4 Plug the electrical cable into to the electrical port of APL1400.
Indice
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
