To add a potentiometer for speed control, change Parameter #5
(Standard Speed Source) to 0-10 VDC (03).
Once the PROGRAM mode is accessed, use the and buttons to
scroll to the desired parameter number, and press the Mode button
to see the parameter setting. Use the and buttons to change
the parameter setting and press Mode to store the new setting.
Connections:
Below is a sample wiring diagram for two-wire start/stop control. The
drive is ready to use right out of the box, with these simple control
wiring connections; no parameter adjustments are required. Speed
is controlled from the and buttons on the front of the drive.
CONFIGURING THE SCF DRIVE
Entering Program Mode:
To access the parameters, press the Mode button. This will
activate the password prompt. The display will read “00” and the
right-hand decimal point will be blinking. Use the and buttons
to scroll to the password value (the factory default password is 225)
and press MODE to enter.
Press Mode
Upper right decimal point blinks
Press Mode to enter password
Display reads “00”
Use and to scroll to the password
value (factory default password is 225)
SCF PARAMETER MENU
No. Parameter
Name Range of Adjustment Factory Default
01 Line Voltage High (01), Low (02) High (01)
02 Carrier Frequency 4 kHz (01), 6 kHz (02),
8 kHz (03), 10 kHz (04) 6 kHz (02)
03 Start Method
Normal (01), Start on Power-up
(02), Start w/DC Brake (03),
Auto Restart w/DC Brake (04),
Flying Restart 1 (05), Flying Restart 2 (06),
Flying Restart 3 (07)
Normal (01)
04 Stop Method
Coast (01), Coast with
DC Brake (02), Ramp (03),
Ramp with DC Brake (04)
Coast (01)
05 Speed Source Keypad (01), Preset #1 (02),
0-10 VDC (03), 4-20 mA (04) Keypad (01)
06
13
TB-14 Output
TB-15 Output
None (01), Run (02), Fault (03),
Inverse Fault (04), Fault Lockout (05),
At Set Speed (06),Above Preset #3 (07),
Current Limit (08), Auto Speed (09),
Reverse (10), Min Alarm (11),
Max Alarm (12), Min/Max Alarm (13)
None (01)
None (01)
8 TB-30 Analog Out
None (01), 0-10 VDC Freq (02),
2-10 VDC Freq (03),
0-10 VDC Load (04),
2-10 VDC Load (05)
None (01)
9 TB-31 Analog Out
None (01), 0-10 VDC Load (02),
2-10 VDC Load (03),
Dynamic Braking (04)
None (01)
10 TB-13A Select
None (01), 0-10 VDC (02),
4-20 mA (03), Preset Speed #1 (04),
Run Reverse (05), Start Reverse (06),
External Fault (07), Remote Keypad (08),
DB Fault (09), Auxiliary Stop (10),
Accel/Decel #2 (11),
Keypad Setpoint (12)
None (01)
11 TB-13B Select
None (01), 0-10 VDC (02),
4-20 mA (03), Preset Speed #2 (04),
Decrease Freq (05), Jog Forward (06),
Jog Reverse (07), Auxiliary Stop (08),
Keypad Setpoint (09)
None (01)
12 TB-13C Select
None (01), 0-10 VDC (02),
4-20 mA (03), Preset Speed #3 (04),
Increase Freq (05), External Fault (06),
Remote Keypad (07), DB Fault (08),
Accel/Decel #2 (09),
Keypad Setpoint (10)
None (01)
14 Control
Terminal Strip Only (01),
Remote Keypad Only (02),
Terminal Strip or Remote Keypad (03)
Terminal
Strip (01)
15 Serial Link
Disable (01),
9600, 8, N, 2 with Timer (02),
9600, 8, N, 2, without Timer (03),
9600, 8, E, 1 with Timer (04),
9600, 8, E, 1, without Timer (05),
9600, 8, O, 1 with Timer (06),
9600, 8, O, 1, without Timer (07),
9600, 8, N,
2 with Timer (02)
16 Units Editing Tenths of Units (01), Whole Units (02) Whole Units (02)
17 Rotation Forward Only (01), Forward and Reverse (02) Forward Only (01)
19 Acceleration Time 0.1 - 3600.0 sec 20.0 sec
20 Deceleration Time 0.1 - 3600.0 sec 20.0 sec
21 DC Brake Time 0.0 - 3600.0 sec 0.0 sec
22 DC Brake Voltage 0.0 - 30.0 % 0.0%
23 Min Frequency 0.0 - Max Frequency 0.0 Hz
24 Max Frequency Min Frequency - 240.0 Hz 60.0 Hz
25 Current Limit 30 - 180% 180%
No. Parameter
Name Range of Adjustment Factory Default
26 Motor Overload 30 - 100% 100%
27 Base Frequency 25.0 - 500.0 Hz 60.0 Hz
28 Fixed Boost 0.0 - 30.0% 1.0%
29 Accel Boost 0.0 - 20.0% 0.0%
30 Slip Compensation 0.0 - 5.0% 0.0%
31-
37 Preset Speeds 0.0 - Max Frequency 0.0 Hz
38 Skip Bandwidth 0.0 - 10.0 Hz 0.0 Hz
39 Speed Scaling 0.0 - 6500.0 0
40 Frequency Scaling 3.0 - 2000.0 Hz 60.0 Hz
41 Load Scaling 10 - 200% 200%
42 Accel / Decel #2 0.1 - 3600.0 sec 20.0 sec
43 Serial Address 1 - 247 1
44 Password 000 - 999 225
45 Spd at Min Signal Min Frequency - 999.0 Hz 0.0 Hz
46 Spd at Max Signal Min Frequency - 999.0 Hz 60.0 Hz
47 Clear History Maintain (01), Clear (02) Maintain (01)
48 Program Selection
User Settings (01), OEM Settings (02),
Reset OEM (03), Reset 60 (04),
Reset 50 (05), Translate (06)
User Settings (01)
50 Fault History View Only (N/A)
51 Software Code View Only (N/A)
52 DC Bus Voltage View Only (N/A)
53 Motor Voltage View Only (N/A)
54 Load View Only (N/A)
55 0-10 VDC Input View Only (N/A)
56 4-20 mA Input View Only (N/A)
57 TB Strip Status View Only (N/A)
58 Keypad Status View Only (N/A)
59 TB-30 Output View Only (N/A)
60 TB-31 Output View Only (N/A)
61 PI Mode
Off (01), Normal 4-20 mA (02),
Normal 0-10 VDC (03),
Reverse 4-20 mA (04),
Reverse 0-10 VDC (05)
Off (01)
62 Min Feedback 0.0 - 999.0 0
63 Max Feedback 0.0 - 999.0 100
64 Proportional Gain 0.0 - 99.9 % 5.0%
65 Integral Gain 0.0 - 99.9 sec 0.0 sec
66 PI Accel/Decel 0.0 - 999.0 sec 20.0 sec
67 Min Alarm 0.0 - 999.0 0
68 Max Alarm 0.0 - 999.0 0
69 0-10 VDC Feedback View Only (N/A)
70 4-20 mA Feedback View Only (N/A)
71 Actual Frequency View Only (N/A)
Run/Stop Contact
1 2 5 6 11 12 2 14 13B 13C
Run/Stop Contact
1 2 5 6 11 12 2 14 13B 13C
Speed Pot
Items in blue are included with the PI option.
