Acclaim Lighting LFL2M Istruzioni per il montaggio
P: 866-845-5451 • F: 866-816-6165 • E: [email protected]
Floodlight Installation and
Wiring Instructions
WARNING: To avoid electrical shock. Do not attempt to install the fixture
in wet or rainy conditions. Always turn off electrical power at the circuit
breaker or by disconnecting the fuse.Only use bulbs in compliance with
manufactures specifications.
DO NOT ATTEMPT TO EXCEED MAXIMUM WATTAGE RATING.
TOOLS AND MATERIALS REQUIRED
Blade and or Phillips Head screw driver
Step Ladder(if needed)
Wiring supplires as required by electrical code:
Wire connectors
Electrical tape
UNPACK THE FIXTURE
Check the contents of the box.You should receive:
Outdoor fixture
Mounting Hardware package.
CAUTION
WARNING: Risk of fire.
Before installing your lighting fixture, thoroughly review the section titled wiring connections.
If you do not have sufficient electrical wiring experience, please refer to a do-it-yourself wiring
handbook or have your fixture installed by a qualified licensed electrician.
All electrical connections must be in accordance with local and National Electrical Code(NEC) standards.
If you are unfamiliar with proper electrical wiring connections obtain the services
of a qualified electrician.
GENERAL
Remove the fixture and the mounting hardware package from the box and make sure that no parts are missing by
referencing the illustrations on the installation instructions.
To ensure success of the installation, read these instructions and review the diagrams thoroughly.
Save these instructions for future reference.
This fixture is intended to be mounted to a 4”x4”x2-1/8” deep metal outlet box.
The building structure must directly support the outlet box.
Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the
fuse at the box. Turning the power off using the light switch is not sufficient to prevent electrical shock.
WIRING CONNECTIONS
Required supply circuit: 120V,60Hz.
Connect the white wire from the fixture to the white wire of the supply circuit.
Connect the black wire from the fixture to the black wire of the supply circuit.
Connect the green(or bare copper)colored wire to the grounding conductor of the supply circuit.
Use UL/CSA listed wire connectors suitable for the size, type, and nu mber or conductors.
No loose strands or loose connections should be present.Secure wire connectors with Use UL/CSA listed electrical tape.
LFL2M
1500 Cherokee Parkway, Suite 100, Acworth, GA 30102
Motion Sensor Light Control
•Turns on lighting
when motion is detected.
•Automatically turns lighting off.
•Photocell keeps the lighting off during
daylight hours.
This package includes:
Light Control
Sensor
Cover
Plate
Gas ket
2 Scr ews
Mounting Strap
Mounting Bolt
2 Wire
Connectors
Requirements
•The
light
control
requires
120-volts AC.
•
be wired through a switch.
•Some
codes require ins t a l lation by a qualified
electrician.
•This product
is
intended
for
use
with
the
enclosed
gasket and with
a junction box
marked for use in
locations.
If you want to use Manual Mode,the control must
wet
Set the switch
on
the bottom of the
sensor to TEST.
MANUAL MODE
... back on.
1 Second
OFF then...
* resets to Auto Mode at dawn.
TEST
TEST 1 5 MIN
AUTO
TEST 1 5 MIN
Set switch to
1 or 5 minutes.
Manual mode only works at
night because daylight re-
turns the sensor to AUTO.
Flip the light switch off
for one second then back
on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with
the ON-TIME switch in the 1,
or 5 position.
Mode: On-Time Works: Day Night
Test 10 Seconds x x
Auto 1 or 5 Min x
Manual To Dawn* x
Note:
When first
turned on wait about 40
seconds for the circuitry to calibrate.
Questions or problems? Before
to your retailer, refer to
guide in this manual
troubleshooting
returning
the
Model: LFL2WHM/LFL2ABZM
Rubber
Plug
2
Features
Move switch to
1 or 5 minutes
Mode Switc
Installation
h Summary
off for one second
then ba ck on
MANUAL MODE
AUTO
TEST
If you get confused
while switching
modes, turn
the power off for one minute,then
backon. After the cali bration time the
control
will be in the
AUTO mode.
Flip light switch
For easy installation, select
an existing
light
with
a
wall switch
for
replacement.
For eave mount
only:
1.
S
wing the sensor head towards the
clamp screw
joint.
2. Then rotate
the
sensor
head
clockwise
180°
so the controls
face
down.
Controls
Wall Mount Eave Mount
For under eave installation, the sensor head
must
be rotated as shown
in the next two steps for
proper
operation and to avoid the risk
of
electrical
shock.
Clamp Screw
For best performance,mount the fixture about
8 ft(2 .4m) above the ground.NOTE:If fixture
is mounted higher than 8 ft.(2.4m),aiming the
sensor down will reduce coverage distance.
If the sensor pops out of the ball joint,loosen
the clamp screw and push the sensor back into
the ball joint.Tighten the clamp screw when done.
Controls
Operation
3
1.Remove
the
existing
3.Route
the
light
control’s wires
through
the large gasket holes.
4.Twist
the
junction
box
wires and
wires
together as
shown.
Secure
with
wire
connectors.
White to
White
Black to
Black
Junction box ground wire to
green ground screw on xture.
Gasket
Mounting
Strap
Mounting
Bolt
Rubber
Plug
Install the Light
1.Align the light control
cover
plate and
plate
gasket.Secure with the mounting bolt.
4 To avoid water
damage
and
electrical
shock,
keep
heads holders
below horizontal.
5.Adjust the heads by loosening the lock
nuts but do not rotate the heads more than
180°from the factory setting.When screwing
in the heads,do not overtighten.
Keep
heads
at least
1" (25 mm) from the
sensor.Do
not allow
the sdaeh to block
the lens.
3.If a wet
location
junction
box
was
not
used,
caulk
the wall plate mounting
surface
with silicone
sealant.
Wire the Light Control
WARNING: Turn power off at circuit breaker
or fuse.
fixture.
fixture
light
2.Install the mounting strap as shown using
two screws that fit your junction box.
cover
Lock Nut
Lens
40 ft.
(12 m)
8 ft.
(2.4m)
Maximum Range
Maximum
Coverage Angle
Bottom of Sensor
Avoid aiming the control at:
•Objects that change temperature rapidly,
such as heating vents and air conditioners.
These
heat sources could cause false triggering.
•
1. Turn on the circuit breaker and light switch.
NOTE: Sensor
has
a 40
second
warm up period
before it
will
detect motion. When
turned on, wait 1
minute.
2.Turn
the
RANGE
control to the medium
position
(halfway between MIN and MAX),
and
the
ON-TIME
control to
the
TEST position.
first
Areas where pets or traffic may trigger
the control.
.Nearby large,light-colored objects reflecting
light may trigger the shut-off feature.Do not
point other lights at the sensor
MAX
MIN
RANGE
ON
-TIME
TEST 15
MINUTES
180°
Test and Adjustment
NOTE:
If fixture is mounted higher than 8 ft.(2.4m).
aiming the sensor down will reduce coverage distance
3.Loosen
the clamp screw in the sensor
ball jointand gently rotate the
sensor.
4.Walk
through
the coverage
area
noting where
you
are
when
the lights
turn on
head up
down,
or
sideways
to change the coveragearea.
Keep
the
sensor
at
least
1"
(25 mm)
away from
the bulbs.
5.Adjust
the
RANGE
as
needed.
RANGE
set too
high may
increase false
triggering.
6.
Secure
the
sensor
head
by
tightening the
clamp screw.
Do not
overtighten
the
screw.
7.
Set
the
amount
of
TIME
you
want the lights
to
stay on after motion isdetected
(1
or
5minutes).
Clamp
Screw
Ball
Joint
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higherfor Long
Coverage
Least Sensitive
Most Sensitive
WARNING - Risk
of
re.
Do not aim the heads
at a combustible surface within 3 ft. (1 m).
The detector is less sensitive to motion coming
directly at it
(also ,the LED will flash
several times when motion
is detected).
Motion
Motion
Sensor
Move the sensor
2.Push the rubber plug firmly into place.
4
TROUBLESHOOTING GUIDE
SYMPTOM POSSIBLE CAUSE SOLUTION
Lights
will not 1.Light switch is turned off.
2.Fuse is blown or circuit breaker is turned off
3.Daylight turn-off is in effect
4.Incorrect circuit wiring,if this is a new installation
5.Light control aimed in wrong direction
come
on.
Lights come
on
in
day -
light.
1.Light
control
may
be installed in a relatively
dark location.
2.Light
control
is
in
TEST.
Lights come
on for no
apparent
reason.
1. Light control
may
be
sensing
small
animals or
auto -
mobile
2. Range
is set
too
high.
Lights
stay
on
1. A flood lamp is positioned too close to the light
control or pointed at nearby objects that cause
heat to trigger the light control.
2. The light control may be picking up a heat source
like an air vent,dryer vent,or brightly painted ,
heatreflective surface.
3. Light control is in manual mode.
continuously.
on and 1.Heat or light from the flood lamp may be turning the
light control on and off.
2.Heat being reflected from other objects may be turning
the light control on and off.
3.Light control is in the TEST mode and warming up.
off.
Lights flash once,
then
stay
off
in
manual
mode.
Light control
is
detecting
its
own
lights. the
light
control relatively dark.
SPECIFICATIONS
Range ........ Up to 40 ft.(12 m)
[varies
with surrounding temperature]
Sensing Angle ..... Up to 180°
Electrical
Load... Up to 24 Watt Maximum LED
Power Requirements . 120 VAC, 60 Hz
Operating Modes . . O
TEST, AUT
and MANUAL
MODE
Time Delay ...... 15
minutes
1.Turn switch on.
2.Replace fuse or turn circuit breaker on.
3.Recheck after dark.
4.Verify wiring is correct.
5.Re-aim light control to cover desired area
1.The fixture is operating normally under
these conditions.
2.Set control switch to 1 or 5 minutes
traffic.
1.Re-aim light control
2.Reduce range.
3.The fixture is operating normally under
these conditions.
1.Reposition the flood lamp away from the
light control or nearby objects.
2.Reduce range.
3.Switch light control to AUTO
Lights flash 1.Reposition the flood lamp away from the
light control
2.Reposition light control
3.Flashing is normal under these conditions
Reposition fliid lamp to keep area below
.
Indice
Altri manuali Acclaim Lighting Proiettore
Acclaim Lighting
Acclaim Lighting RDA Manuale
Acclaim Lighting
Acclaim Lighting REA Manuale
Acclaim Lighting
Acclaim Lighting ILB Manuale
Acclaim Lighting
Acclaim Lighting RBE Manuale
Acclaim Lighting
Acclaim Lighting Dyna Drum SO QW Manuale utente
Acclaim Lighting
Acclaim Lighting RDD Manuale
Acclaim Lighting
Acclaim Lighting Dyna Drum HO Manuale utente
Acclaim Lighting
Acclaim Lighting RBC Manuale
Acclaim Lighting
Acclaim Lighting ILA Manuale
Acclaim Lighting
Acclaim Lighting Dyna Accent Manuale utente
