Accton Technology 1000BASE-LX Manuale utente
1000BASE-LX Gigabit Uplink Module
EM4582-LX-SC
uick Installation Guide
Quick Installation Guide
EM4582-LX-SC Gigabit Uplink Module
Slide-in module with 1 1000BASE-LX (SC-type) port
Accton is a trademark of Accton Technology Corporation. Other trademarks or brand names mentioned
herein are trademarks or registered trademarks of their respective companies.
International Headquarters
No. 1 Creation Road III,
Science-based Industrial Park
Hsinchu 300, Taiwan, R.O.C.
Phone: 886-3-5770-270
FAX: 886-3-5770-267
Internet: suppor[email protected].tw
USA Headquarters
6 Hughes
Irvine, CA 92618
Phone Numbers -
Sales: 800-926-9288
Support: 888-398-4101 or 949-707-4847
RMA: 800-762-4968
FAX: 949-707-2460
Copyright © 2000 by Accton Technology Corporation. All rights reserved.
No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of Accton Technology Corporation.
Accton makes no warranties with respect to this documentation and disclaims any implied warranties of mer-
chantability, quality, or fitness for any particular purpose. The information in this document is subject to
change without notice. Accton reserves the right to make revisions to this publication without obligation to
notify any person or entity of any such changes.
EM4582-LX-SC
E102000-R01
150514-102
i
Contents
Description of Hardware 1
Gigabit Uplink Module 1
Gigabit Port LEDs 1
Installing the Module 2
Package Contents 2
Handling the Module 2
Instructions 2
Maximum Cable Lengths 5
Troubleshooting 6
Product Specifications 6
EMI Certification 7
FCC Class A Certification (USA) 7
Canada Department of Communications - Class A 7
BSMI Class A (Taiwan) 7
VCCI Class A Compliance (Japan) 7
CE Mark Declaration of Conformance for EMI and Safety (EEC) 8
Safety Compliance 8
Warning: Fiber Optic Port Safety 8
Avertissment: Ports pour fibres optiques - sécurité sur le plan optique 8
Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit 8
Underwriters Laboratories Inc. (USA) 9
Wichtige Sicherheitshinweise (Germany) 9
Warranty 10
Optional Hardware 10
Contents
ii
1
Description of Hardware
Gigabit Uplink Module
The EM4582-LX-SC fiber optic module is designed for use in Accton switch models
which have a single-port Gigabit Ethernet transceiver slot. At present, suitable units
include these CheetahSwitch Workgroup models – ES3514F, ES3526F, ES3526G, and
ES3552.
Detailed information about configuring these modules and advice about
Fast Ethernet configuration rules can be found in the switch’s user guide.
Warning: Before installing or removing the EM4582-LX-SC module, first disconnect the
switch from the main power supply. For full safety instructions, please refer to
the user guide that accompanies the switch.
Accton’s EM4582-LX-SC fiber optic module provides a Gigabit port which can be
used for a high-speed backbone or server connection. It contains one 1000BASE-LX
port that can be connected to a site up to 5 km (16,404 ft) away with single-mode
fiber cable.
Gigabit Port LEDs
Port LEDs are provided for the module on the front panel of the switch for
“at-a-glance” network monitoring. The following table details the indicator functions
provided by the switch:
Extender Module LEDs
LEDs Condition Status
Status On A module is installed in this slot.
Activity On Traffic is passing through the port.
User Guide
2
Installing the Module
Caution:
Do not install this module in any unit other than the ES3514F, ES3526F,
ES3526G, or ES3552.
Contact your distributor for advice on newly released
switches which may be designed for use with these modules.
The EM4582-LX-SC fiber optic module is field installable. Just follow the instructions
below.
Package Contents
This package includes:
• One EM4582-LX-SC fiber optic module
• This User Guide
• Owner registration card
Handling the Module
Caution: The EM4582-LX-SC module can easily be damaged by electrostatic discharge.
To prevent electrostatic damage, observe the following guidelines:
• Do not remove the module from its packaging until you are ready to install it.
• Do not touch any of the module’s pins, connectors or components.
• Hold the module only by its edges or front panel.
• Wear an anti-static wristband connected to a suitable earth ground whenever
handling the module.
• Store or transport this module only in appropriate anti-static packaging.
Instructions
Caution: The switch must be powered off before installing or replacing any module.
1. Power off the switch: Disconnect the AC power cord from the switch. If a
redundant power unit (RPU) is present, disconnect its DC cable connection
from the switch.
2. Remove network cables: If you are replacing a module, remove the cable
attached to any port on the module.
3. Loosen the screws on the installed module or slot faceplate: Using your
fingers or a flathead screwdriver, turn the screws securing the module (or
faceplate on the slot) in a counter-clockwise direction until they are free of the
chassis. Be sure not to completely remove the screws from the module or
faceplate.
4. Remove the installed module or faceplate: Firmly pull on the screws until the
module is free of the switch. Carefully slide the module straight out of the slot.
Installing the Module
3
Keep the original faceplate for future use. If you should remove the module,
replace the faceplate to prevent dust and debris from entering the unit and to
maintain proper air flow.
5. Insert the new module into the switch: Holding the new module with the text
on the front panel upright, carefully slide the module into a lower slot on the rear
panel, and press gently until it snaps into place. Be sure the new module’s front
panel is flush with the switch panel.
Note: Media expansion modules can only be placed in the lower slots.
User Guide
4
6. Secure the new module: Secure the new module in place by screwing the
attached screws clockwise into the switch’s chassis. Tighten them enough to
secure the module, but not so tight as to prevent them from being unscrewed
by hand.
7. Connect the network cable to the module: Connect fiber cable to the port on
the newly installed module. See “Maximum Cable Length” on page 5 in this
guide for further information.
8. Power on the switch: Reconnect the previously removed power sources to the
switch. Check the LED indicators for the fiber ports on the module’s bracket to
ensure that they are operating correctly. Refer to “Gigabit Port LEDs” on page 1
for a description of the LED indications. If the module does not respond, see
“Troubleshooting” on page 6.
Refer to the following manuals for the base unit for further details on using this module:
Quick Installation Guide - connection options and network applications
Management Guide - configuration options
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Accton Technology Hardware di rete
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
