Acer RS700 Manuale utente
AcerAltos RS700 EnclosureAcerAltos RS700 Enclosure
Installation GuideInstallation Guide
ii
CopyrightCopyright
Copyright 1998 by this company. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of this company.
DisclaimerDisclaimer
This company makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Further, this company reserves the
right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
iii
IMPORTANT SAFETYIMPORTANT SAFETY
INSTRUCTIONSINSTRUCTIONS
1. Read these instructions carefully. Save these instructions for future
reference.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The
product may fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided
for ventilation; to ensure reliable operation of the product and to protect
it from overheating, these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register, or in a built-in installation unless
proper ventilation is provided.
7. This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
8. This product is equipped with a 3-wire grounding-type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-
type power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your obsolete
outlet. Do not defeat the purpose of the grounding-type plug.
9. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
iv
10. If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does
not exceed the extension cord ampere rating. Also, make sure that the
total rating of all products plugged into the wall outlet does not exceed
15 amperes.
11. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the
product.
12. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks.
Refer all servicing to qualified service personnel.
13. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed
b. If liquid has been spilled into the product
c. If the product has been exposed to rain or water
d. If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of
other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to
normal condition.
e. If the product has been dropped or the cabinet has been damaged
f. If the product exhibits a distinct change in performance, indicating
a need for service
14. Replace battery with the same type as the product's battery we
recommend. Use of another battery may present a risk of fire or
explosion. Refer battery replacement to a qualified serviceman.
15. Warning! Battery may explode if not handled properly. Do not
recharge, disassemble or dispose of in fire. Keep away from children
and dispose of used battery promptly.
v
16. Use only the proper type of power supply cord set (provided in your
keyboard/manual accessories box) for this unit. It should be a
detachable type: UL listed/CSA certified, type SVT/SJT, rated 6A 125V
minimum, VDE approved or its equivalent. Maximum length is 15 feet
(4.6 meters).
vi
FCC Class B Radio FrequencyFCC Class B Radio Frequency
Interference StatementInterference Statement
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/television technician for help.
Notice 1:
The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Notice 2:
Shielded interface cables, if any, must be used in order to comply with the
emission limits.
vii
About this ManualAbout this Manual
Purpose
This manual aims to give you all the information you need to install the
enclosure.
Conventions
The following conventions are used in this manual:
NOTE
Gives bits and pieces of additional
information related to the current topic.
CAUTION
Suggests precautionary measures to avoid
potential hardware or software problems.
viii
ix
Table of ContentsTable of Contents
Chapter 1 Introduction
Overview .......................................................................................1
Standard Configuration..................................................................1
Features .......................................................................................3
Front Panel..........................................................................5
Rear Panel..........................................................................6
Getting Started...............................................................................6
Chapter 2 Hardware Installation
Drive Tray and Back Plane Board .................................................8
Drive Tray ...........................................................................8
To install a hard disk drive:.................................................9
Back Plane Board .............................................................11
Removing and Installing the Redundant Power Supply...............12
Removing a Redundant Power Supply.............................13
Installing a Redundant Power Supply ...............................13
Installing the RS700-RM101/102 into the AcerAltos
Rack..................................................................................15
Vertical Mounting Hole Pattern .........................................15
Chapter 3 Setting Up the RS700
For RS700-TR101/RM101 Models..............................................18
For RS700-TR102/RM102 Models..............................................19
Connecting Two RS700s into a SCSI Channel (for
TR102/RM102 only)..........................................................20
x
Chapter 4 Removing and Installing the Enclosure
Panels
Removing the Left and Right Panel ............................................22
Installing the Enclosure Frame ...................................................23
Chapter 5 Cluster Server Connection
Introduction .................................................................................24
Cluster solution for AcerAltos Server ...............................25
Acer’s Cluster Solution................................................................26
Solutions ........................................................................26
The Architecture of Acer’s Cluster Server........................28
Two-node Cluster Cable Kits for Rackmount or Stand-
Alone.................................................................................29
System Requirements.................................................................30
Hardware Requirements ..................................................30
Software Requirements....................................................30
Hardware Installation and Configuration.....................................31
Hardware Installation........................................................31
Hardware Configuration....................................................31
Planning your Cluster Environment.............................................36
Windows NT Configuration...............................................36
Network Requirements.....................................................36
Software Installation and Configuration ......................................38
Install Windows NT server 4.0 on node1....................................39
Install Windows NT server 4.0 on node2....................................40
Check the Functions of Network Between Two Nodes...............41
Format the Shared Drives on the AcerAltos RS700 ...................42
Install MSCS (Microsoft Cluster Server) on node1.....................44
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Acer Allegato
