Acer View 54e Manuale utente

User’s Guide 1

AcerView 54e (15” monitor, 13.6” viewable

image)

1. Installing the Monitor

Product Package

Open the shipping carton and check the contents. If any item are missing or

damaged, contact your dealer immediately.

The package should include the following items:

ŸColor monitor

ŸSwivel base

ŸUser‘s guide

ŸPower cord

ŸSignal cable

Installing the Swivel Base

Follow these steps to install the swivel base:

2User’s Guide

Turn the monitor on its

side or upside-down.

Insert the pegs on the

swivel base into the

cavities at the bottom of

the monitor. Push on

the swivel base until the

latch clicks shut.

Installing the Monitor

This monitor is equipped with an autosensing power supply for voltage

ranges 100-120VAC/200-240VAC, 60/50 Hz. Confirm the line voltage

designation on the rear panel of the monitor.

Follow these steps to install the monitor:

Before you connect the

cables, make sure that

the monitor and the

system unit power

switches are Off.

Plug one end of the 15-

pin signal cable to the

monitor and the other

end to the video signal

connector at the rear of

the system. Tighten the

two screws on the cable

User’s Guide 3

connector.

Connect the power

cable.

4User’s Guide

2. Control Functions

The monitor digital control functions are located on the front panel. They

are shown in the figure below and described in the following paragraphs.

1. Power Switch 7. Vertical Size

2. Adjust 8. Horizontal Phase

3. Select 9. Horizontal Size

4. Trapezoid 10. Contrast

5. Pincushion 11. Brightness

6. Vertical Center

User’s Guide 5

LED indicators

Each LED represents a different display adjustment. Use the Select button

to choose the item to be adjusted and the Adjust button to change the

setting.

.Brightness: Adjusts the brightness of the display.

.Contrast: Adjusts the contrast, the difference between

the light and dark areas on the screen.

.H-Size: Adjusts the display width (horizontal size).

.H-Phase: Adjusts the horizontal position of the display

(left or right).

.V-Size: Adjusts the vertical display height (vertical

size).

.V-Center: Adjusts the vertical position of the display

(up or down).

.Pincushion: Controls the concave and convex curve at

the vertical edges of the display.

.Trapezoid: Controls the trapezoidal distortion on the top

6User’s Guide

or bottom of the display

The LED indicator goes off after 20 seconds of inactivity. If any settings

have changed, the monitor automatically saves the new settings.

Select

Press the or button to cycle through the adjustment options to

choose H-Phase, H-Size, V-Center, V-Size, Contrast, Brightness,

Trapezoid, and Pincushion. The corresponding LED indicator lights up

when selected. Use the Adjust buttons to change the settings.

Adjust

Adjusts the settings for H-Phase, H-Size, V-Center, V-Size, Contrast,

Brightness, Trapezoid, and Pincushion. Use the Select button to choose the

item to be adjusted and press or to change the setting.

Power Switch

Turns the monitor on (I) or off (O). The power switch is located at the base

of the monitor. The LED indicates the ON/OFF status of the unit.

Reset

Adjusts all settings to factory defaults.

User’s Guide 7

3. How To Adjust the Monitor

Press the Select key ( or ) to choose the item to be adjusted.

Press the Adjust key ( or ) to change the setting.

Repeat the above procedure to change other items.

The monitor automatically saves the new settings after 20 seconds of

inactivity.

In the event that display distortion is incurred due

to magnetic field interference, face the monitor to

the east for the best display quality.

4. Microcontroller Features

The microcontroller automatically detects the video board installed in your

system. When you turn on the monitor, the microcontroller first checks the

display mode memory stored in the user setting area of the video board, and

then the factory presetting area. It then adjusts to the proper display mode.

Display Modes Memory

The microcontroller has the memory capacity to store 32 different display

modes, including timing formats and display settings. This memory

capacity is divided into two parts: the user setting area and the factory

presetting area. The former can store 20 display modes. The latter can store

12 display modes and has already stored 9 display modes.

8User’s Guide

User Setting Area

The user setting area on the microcontroller maintains in its memory the last

20 display modes set by the user. You can change the settings, or add a

nonstandard mode. The microcontroller always detects and displays the last

mode stored in the user setting area first when the monitor is turned on.

Factory Presetting Area

There are 9 preferred display modes preset in the microcontroller. These

display modes are preset at the factory and include the most popular display

modes currently available (see the Specifications section). The

microcontroller searches for a proper display mode in this area if it fails to

find a proper display mode in the user setting area.

User’s Guide 9

5. Signal Connector Pinouts

To connect VGA, 8514A or IBM-compatible graphics adapters, use a 15-

pin mini D-type male connector.

15-Pin Mini D-Type Male Connector

Pin Assignment

1Red Video

2Green Video

3Blue Video

4Ground

5Ground

6Red Ground

7Green Ground

8Blue Ground

9No Connection

10 Sync Ground

11 Ground

12 Serial Data I/O

13 H. Sync

14 V. Sync

15 Serial Clock Input

10 User’s Guide

6. Power Saving Feature

This monitor’s power saving feature complies with these VESA power

saving modes:

Mode H.Sync V.Sync LED Power Consumption

Normal On On Green 90 w

Stand-by Off On Amber <15 w

Suspend On Off Amber <15 w

Off Off Off Amber

Blinking <5 w

The monitor uses the H.Sync and V.Sync signals to determine the operation

mode to enter.

The monitor power-saving feature automatically turns off H.Sync and

V.Sync if there is no input from the system for a certain period of time. To

use this feature, you need a green PC that is compliant with the VESA

power saving feature or a software utility to detect system input such as the

keyboard or mouse.

Time Settings

Time settings are adjusted from the system unit by software. To fulfill the

requirements in the NUTEK specification 803299/94 the total time from

indicated inactivity to Power Saving Position A2 (VESA Off) must not be

set to more than 70 minutes. We recommend you switch off the monitor

when you do not intend to use it for awhile.

Altri manuali per View 54e

Indice

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione

LG M1950D-PZ Manuale utente