1. Press the MODE buon to move between all funcons in
sequence as “ ” from one funcon screen to another when the .
speed sensor does not detect any signal input.
2. Press the MODE buon to move paral funcons in loop sequence
as “ ”when speed sensor detects signal input.
BUTTON OPERATIONS
MODE BUTTON
Gear Indicator Tranning Operations:
Optional Remote Control Switch for LAP timer
1. Setup operaons include 12/24hour clock, bar rpm scale, shi warning
RPM, numbers of engine rotaon per signal, wheel circumference, signal
divider, units, maintain reminder, units of temperature, temperature
warning, fuel meter input resistance selecon and odometer adjustment.
These must be set up step by step. The computer will be automacally
revert to normal mode if no buon is pressed for 75 seconds at any
seng screen.
Clock, RPM, Wheel, Divider, Unit, Maintain, Thermometer, fuel meter and ODO SET UP
Tire Size
Circumference
number
(mm)
Tire Size
Circumference
number
(mm)
Tire Size
Circumference
number
(mm)
23 inch
24 inch
25 inch
26 inch
19 inch
20 inch
21 inch
22 inch
15 inch
16 inch
17 inch
18 inch
1835
1915
1995
2075
1516
1596
1676
1756
1197
1277
1357
1436
WHEEL CIRCUMFERENCE TABLE
1. The details below have been calculated using following formula: Tire
Diameter (inches) x 25.4(mm/inches) x 3.1416 = wheel circumference
(in mm).
2. Idenfy the re size of your ATV/Motorcycle when you need to change
different re size and key in the corresponding number shown in the
following chart.
3. These values are approximate and will differ for different brands of
tyre, we would always recommend that you measure the distance
travelled per revoluon of the wheel in mm and enter this into the
computer.
4. The computer calculates the wheel rotang length between 2 passes
of the magnet; use this table to find the sengs when you are using a
reed sensor or an universal hall sensor with magnet to measure your
speed.
5. If you are using a cable drive speed sensor then enter the number of
turns of the cable perf the wheel into the pulses screen.
6. You can use more magnets, enter the number of magnets fied into
the pulses screen.
7. If using a sprocket tooth counter speed sensor or internal pulse
gearbox speed sensor enter the number of pulses per wheel
revoluon into the pulses screen.
2. Press both MODE & RESET buons to go into seng mode. In seng
mode, each press of the RESET buon increments the flashing digit by 1
or converts units. Press MODE buon to confirm the digit seng and
jump to next digit or next seng screen to be set. Press MODE buon for
2 seconds at any seng screen to finish the seng and go to normal mode.
Shift Warning RPM Operation
1. Press MODE buon to the RPM screen; pull on the throle unl
the desired shi warning RPM.
2. Press RESET buon to confirm and set up the shi warning RPM.
3. Bar-graphic tach ometer and warning LED will flash to warning you
shi gear.
4. Press RESET buon for 2 seconds at the RPM screen to re-adjust
the shi warning RPM.
RESET BUTTON
Reset buon cycles through funcons in reverse order
DATA RESETTING AND PROGRAMMING MODES
1. Press MODE or RESET buon to reach the desired screen then
press RESET buon for 2 seconds to reset TRIP 2, MAX SPD, MAX
RPM and MAX data from stored values to zero individually. The
maintain reminder data will be reset to the preset value rather
than zero.
2. The data of Trip 1, AVG & RT will all be reset at the same me when
one of the 3 data funcons is being reset.
3. ODO, clock, HRTT and TT data cannot be reset.
4. Gear indicator flashes the default 0 gears.
5. Press RESET buon to select the number of gear, user can select 4-8 gears or
“0” to disable the gear funcon.
6. Press MODE buon to confirm the number of gears and go to the number
gear rao seng mode.
7. It displays and flashes “1”, shi bike’s gear to the 1st gear, run the engine to
between 2000-4000RPM.
8. Hold the speed and the RPM for about 5 seconds unl the “-“flashing. The
flashing “-“aer the gear “1” means the 1st gear be set.
9. Press MODE buon to confirm the set and go to the 2nd gear seng.
10. It displays and flashes “2”, shi bike’s gear to the 2nd gear, run the engineto
between 2000-4000RPM.
11. Hold the speed and the RPM for about 5 seconds unl the “-“flashes. The
flashing “-“aer the gear “2” means the 2nd gear is set.
12. Press MODE buon to confirm the seng and go to next gear seng.
13. Repeat the same operaons as items 11-14 to set other gears unl the last
gear is set. Press MODE buon to return to normal mode.
14. At gear indicator seng mode, press and hold MODE buon for 2 seconds
to abort the seng if you need to re-set at any seng screen.
1. The remote control switch has 2 buons: MODE and LAP. The MODE buon
has the same funcon as on the main unit.
2. Press and hold the LAP buon for 2 seconds to go into the LAP mode.
3. LAP Record operaons:
a. In LAP mode, press LAP buon to convert start or stop the LAP recording
funcon, each press of MODE buon records a set of data LAP and
displays LAP mer for 3 seconds then changes display to speed mode
automacally, press and hold the LAP buon for 2 seconds to go out LAP
mode and return to normal mode.
b. The first data of recording funcon will be renewed by new data when lap
exceeds 99 laps, then each new data renews earliest data one by one.
LAP review operations:
1. In the LAP mode, press MODE buon to review the 1st stored data, it
displays number of lap and lap mer.
2. Press the RESET buon to switch between lap mer of the same LAP; each
press of the MODE buon displays data for the next lap.
3. Press and hold LAP buons for 2 seconds to go out LAP mode and return to
normal mode.
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Follow the item 2 to set sensor type of LAP mer and jump to freezing
me seng.
20. **It displays flashing 01 and SEC, the range is from 01 to 20 seconds,
the freezing me seng will ignore signals received by the unit within
the set freezing me aer it received a signal. Follow the item 2 to set
freezing me and jump to odometer seng.
21. It displays “ODO & 00000X km”, the “X” is from odometer tesng in
factory, follow item 2 to set a desired odometer value and jump to
clock seng or return to Normal Mode. This seng screen will
disappear when the odometer is over 30km (18.6Miles) or your seng
is over 30km
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
**
**
**
Mode
2 sec.
RESET
Mode
+
2 sec.
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
RESET
2SEC
3. It displays "12 or 24H and XX:XX:XX " symbols and AM/PM when you
select 12H. Operate buons as described in item 2 to finish clock
seng and jump to shi RPM warning seng.
4. It displays the default "RPM r06500", the digit “0” flashes. Follow the
item 2 of buon operaon to finish the shi RPM warning seng and
jump to engine specificaon seng.
5. It displays "RPM SP 1r1P", the default value is 1r1P; there are 6 opons:
1r1P, 1r2P, 1r3P, 1r4P, 2r1P, 3r1P,. “r” means the numbers of
enginerotaon, “P” means number of signals from engine. For example
the value 2r1P means the engine rotates 2 turns to output one signal.
6. Press RESET buon to move in loop sequence from one to another
value of the 6 values. Press MODE buon to confirm the seng and go
to speed sensor type screen.
7. It displays SPD SEn HALL or SPD SEn rEEd, HALL type is for Acewell's
unique 2 wires hall sensors only, rEEd type is for reed sensors, gear
sensors and signals from ECU. A gear sensor has 3 wires and must be
powered from the bike. Follow item 2 of buon operaon to confirm
the sensor type and jump to wheel circumference seng screen.
8. In "SPD cXXXX" display, "c" means "Circumference", following 4 default
digits; flashing digit is digit to be set. Follow the item 2 of buon
operaon to finish the wheel circumference seng and jump to signal
divider seng.
9. It displays "SPD P-001", the pulses screen, the number of pulses into the
computer per turn of the wheel. Follow item 2 of buon operaon to
finish the seng and jump to unit seng.
10. It displays KM/H or MPH, each press of RESET buon converts unit;
press MODE buon to confirm unit seng and jump to decimal point
seng.
11. It displays “99.9Km/H SPD & on” or “99Km/H SPD & oFF”, the decimal
point will disappear when Off is selected. Follow the item 2 of buon
operaon to finish the decimal seng and jump to maintain reminder
seng.
12. It displays and TRIP, RT or oFF, TRIP is 1000km (621Miles) and RT is
100 hours by default. Follow the item 2 of buon operaon to finish
the maintenance reminder seng and jump to voltage warning seng.
The maintenance reminder funcon will be not be shown when “OFF”
is selected.
13. It displays “ b-on and a flashing numbers of voltage” to be set, “b-on”
means baery warning on voltage – when the voltage falls below this
the LED will flash, seng range from 11.0 to 15.0V. It displays “
b-off and a flashing numbers of voltage”, “b-off” means baery
warning off voltage, seng range from 11.0 to 15.0V to, but b-off
voltage must larger than b-on voltage – when this voltage is exceeded
the LED will go off. It displays “ b-HI and a flashing numbers of voltage”
to be set, “b-HI” means baery warning on voltage – when the voltage
is exceeded the LED will come on, seng range from 11.0 to 15.0V“.
Follow the item 2 of buon operaon to finish the voltage warning
seng and jump to thermometer 1 seng.
14. It displays " 1°C, °F or oFF", each press of RESET buon converts ,°C or °F
Off, the temperature bars will disappear when you select oFF mode;
press MODE buon to confirm temperature seng and jump to
temperature 1 warning seng.
15. It displays " 1 XXX" and the selected unit. Follow the item 2 of buon
operaon to finish the temperature warning seng and go to
thermometer 2 seng.
16. thermometer 2 seng It displays "** 2 °C , °F or oFF", each press of
RESET buon converts °C, °F or Off, press MODE buon to confirm
temperature seng and jump to scan seng.
17. It displays SCAn and on or oFF, It displays “flash 01 & SCAn” if you
select Scan on, it means the me in seconds to display each funcon,
for example 05 means every 5 seconds auto change to the next
funcon, the set range is 01-20. Follow the item 2 of buon operaon
to finish the SCAN seng and go to fuel sensor resistance seng.
18. It displays “on, off or rES” and , it displays fuel tank and full bars as
well flash XXXXr, it means full tank resistance seng, the seng range
of “on” from 10r to 1000r. It displays fuel tank and one bar as well as
flash XXXXr, it means empty fuel sensor resistance seng. Follow the
item 2 to select a resistance same as your fuel sender and jump to
sensor type of **LAP mer seng. The fuel meter bar will disappear if
you select oFF mode. In “rES” mode connecng the input wire to 0v
can bring on the fuel symbol and/or LED indicator instantly.
19. It displays Ir, EF1, EF2 or EF3, Ir means you elect IR receiver as the
sensor for LAP mer, and the selecon of EF1, 2 or 3 is a magnec
field sensor for LAP mer, the number of 1, 2 or 3 is means the
number of magnec sensor in track, for example EF2 means the track
has 2 magnec sensor and it will combine 2 sensing signals in one.
1. If using a rear wheel or gearbox speed sensor, put bike on a rolling road or
securely mounted centre stand, if measuring front wheel speed the following
can only be done if the vehicle is moving.
2. Change the LCD screen to display digital RPM.
3. Press and hold MODE buon for 2 seconds to go into the number of gears
seng mode.
