ACME LED-RC8 Manuale utente
1. General Instructions
A profession remote controller with 4Ch. /8Ch. Switchable
Can connect witch LED-CC or LED-PC300/100 to control passive LED fixtures
9 different hold-color buttons for instant colors
12 different color chases triggered by music
32 different mix colors, including color fade
Speed and dimmer adjustable by fader
Full on and blackout functions
Power supply: DC 9V 300 mA
Dimension: 180X 130 X 50 mm
Weight: 1 kg
Function Instructions:
Mode select Use to select Fixed Color / Chase 1 / Chase 2 / Spectrum mix mode
Fixed color
/ chase
1. In Fixed Color mode, use to select color on Red /Orange / Yellow / Green /
cyan / Blue / Purple / Magenta /White
2. In Chase 2 mode (the LED blinking), use to select 8 chase or random chase.
Chase 1 fader
In Chase 1 (the LED on) mode, use the fader to select color chases on
Standard chase / Bright chase / Mood chase / spectrum random chase /
Spectrum sequence chase / Dynamic chase / Red-Green+ Blue / Green-Red +
Blue / Blue-Red / Yellow-Blue / Red-Green / Yellow-Green
Spectrum Mix
fader Use to select 32 spectrum mix colors in Spectrum mix mode.
Speed fader Use to adjust chase speed in the range of 0.1 to 2.5 seconds
Fade Time
fader Use to adjust fade time. Fade time is amount of one color to fade in or fade out
Master fader Use to dimmer / shutter the fixture
Black out Blackout the fixture
Full on All lighting effect at once
Sound to
chase Use to receive audio signal for sound activated
Rear View:
Power Switch Turn On/Off the power
Channel Mode Switch Translate between 4 channels mode and 8 channels mode
DC Input DC 9V 300mA min
DMX Output Output DMX signal to the connected fixture
2. Address setting
Each fixture needs to have an address set to receive the data sent by the controller. There are 8
addresses that you can set for LED lightings.
Please follow the instructions below to set the address:
Set LED-RC8 to 4 Ch. or 8 Ch. mode.
Connecting all LED lightings to the LED-RC8 and power them on.
Hold the “black out” button for about 5seconds until the LED blinking.
The first lighting will be on.
Set address for the LED lightings by pressing the chase 1-8 buttons.
Press the “sound to chase” or “ full on” button to select other fixtures,
and addressing for them.
Press the “black out” button for about 5 seconds to quit address setting.
3. How to Connect the unit
Please refer to the following diagram to connect the fixtures:
A. Connect with COLOR BALL/COLOR SPOT
B. Connect with COLOR PAR
Button address
Chase 1 1
Chase 2 2
Chase 3 3
Chase 4 4
Chase 5 5
Chase 6 6
Chase 7 7
Chase 8 8
Широкий ассортимент ACME на www.maxlight.ru
Indice
Altri manuali ACME Attrezzatura per DJ
ACME
ACME Ellipsoidal Manuale utente
ACME
ACME SAM-50 Manuale utente
ACME
ACME SPLENDOR 90 Manuale utente
ACME
ACME Dotline 360 Manuale utente
ACME
ACME LED-BL8 Manuale utente
ACME
ACME MH-600A Mobile Color Manuale utente
ACME
ACME IU-01 Manuale utente
ACME
ACME Color Par 36 Manuale utente
ACME
ACME MH-275R Manuale utente
ACME
ACME E-10T WW DXX Manuale utente
ACME
ACME LED-MS50A Manuale utente
ACME
ACME CYC-200 FC Manuale utente
ACME
ACME ORION XP-260 BEAM Manuale utente
ACME
ACME CP-56U Manuale utente
ACME
ACME FURY LED RGB Manuale utente
ACME
ACME Ellipsoidal 10 DMX Manuale utente
ACME
ACME LED-256D RGB Manuale utente
ACME
ACME XP-1200F Manuale utente
ACME
ACME Solaris CM-S6 Manuale utente
ACME
ACME LED-245 II Manuale utente
