ACT ACTpro MIFARE Series Manuale utente

pro

ACTpro MIFARE Readers

Installation Manual

ACTpro MF 1030e - Slimline Proximity Reader

ACTpro MF 1040e - Proximity Reader

ACTpro MF 1050e - PIN & Proximity Reader

ACTpro MF 1030PM - Panel Mount Proximity Reader

ACTpro MIFARE Readers Installation Manual

Contents

Page No.

Specications Table ................................................................................ 3

Product Description ................................................................................ 4

Reader Connections 1040e/1050e.......................................................... 4

Reader Connections 1030e..................................................................... 5

CAT 5/6 Colour Code .............................................................................. 5

Clock & Data Entry and Exit Reader Wiring Diagrams ............................ 6

Wiegand Entry and Exit Reader Wiring Diagrams................................... 7

Reader Conguration .............................................................................. 8

Reader Reprogramming .......................................................................... 9

1050e Backlight Operation.................................................................... 10

Power On Beep Codes.......................................................................... 10

1030PM Connections to Controllers/Doorstations ............................... 11

1030PM Mounting Diagram & Instructions ........................................... 12

1040e/1050e Surface Mounting Diagram ............................................. 13

1030e Mounting Diagram...................................................................... 13

1040e/1050e Flush Mounting Diagram ................................................. 14

1040e/1050e Flush Mounting to UK Pattress Box Diagram ................. 15

Product Code Description

ACTpro MIFARE 1030e MIFARE Classic Proximity reader, mullion mount

ACTpro MIFARE 1030PM MIFARE Classic Proximity reader, panel mount

ACTpro MIFARE 1040e MIFARE Classic Proximity reader, surface / ush

ACTpro MIFARE 1050e MIFARE Classic Prox & PIN reader, surface / ush

ACTpro MIFARE Readers Installation Manual

MIFARE 1030e MIFARE 1030PM MIFARE 1040e MIFARE 1050e

Connections Pigtail Terminal Block Terminal Block Terminal Block

Dimensions

W x H x D 37 x 120 x 15mm 63 x 58 x 23mm 95 x 128 x 19mm 95 x 128 x 21mm

Mounting Mullion Panel Flush or Surface Flush or Surface

Weight 150g 65g 142g 155g

Power Supply 12Vdc-24Vdc 12Vdc-24Vdc 12Vdc-24Vdc 12Vdc-24Vdc

Selectable

sector,serial &

reverse serial

Yes Yes Yes Ye s

Current

Consumption

Typical

30mA 30mA 70mA 70mA

Current

Consumption

(Peak)

130mA 70mA 140mA 140mA

Operating

Temperature -10°C/50°C -10°C/50°C -10°C/50°C -10°C/50°C

Transmit

Frequency 13.56MHz 13.56MHz 13.56MHz 13.56MHz

Keypad No No No Yes

Environmental

Rating IP67 IP67 IP67 IP67

Cable

Distance 100 m 100 m 100 m 100 m

Output

Formats

Wiegand or

Clock & Data

Wiegand or

Clock & Data

Wiegand or

Clock & Data

Wiegand or

Clock & Data

Indoor &

Outdoor Yes Yes Ye s Ye s

PIN or Prox Prox Prox Prox PIN & Prox

Speciﬁcations Table

ACTpro MIFARE Readers Installation Manual

Reader Connections - ACTpro MIFARE 1040e/1050e

RED

GREEN

+12V DC

Data

CLOCK

SENSE

BUZZ

Sector/Serial

Operation Jumper

Product Description

ACT MIFARE classic readers support all ACT MIFARE cards and fobs.

They can be congured to read serial, reverse serial or sector data from

any third party MIFARE Classic card.

• Compatible with ACT MIFARE cards and fobs

• Congured to read ACT Sector data, Serial Number or reverse

serial number

• Congured to read Sector data form any MIFARE Classic card

(Read key required)

• Congured for Wiegand or Clock&Data output

• Congurable backlight (1050e only)

ACTpro MIFARE Readers Installation Manual

Reader Connections - ACTpro MIFARE 1030e

ACTpro MIFARE 1030e is supplied with 3m pigtail cable.

CAT 5/6 Colour Code

The following is suggested colour coding if using CAT5 or CAT6 cabling.

Reader

Output

Colour

Sense White/Green

Clock / D1 Green

Data / D0 Blue

+12V Orange

(0V) GND White/Orange

Red LED Brown

Green LED White/Brown

Orange &

Purple

Programming Sector/

Serial

ISP Grey (Unused)

CLOCK/D1 (Green)

SENSE (White)

DATA/D0 (Blue)

+12V (Red)

0V/GND (Black)

RED LED (Brown)

GREEN LED (Yellow)

(Orange)

(Purple)

ISP (Grey) - Unused

}Programming

Sector/Serial

ACTpro MIFARE Readers Installation Manual

Clock & Data Entry Reader - Wiring

Clock & Data Exit Reader - Wiring

SENSE (White)

CLOCK / D1 (Green)

DATA / D0 (Blue)

+12V (Red)

OV / GND (Black)

RED (Brown)

GREEN (Yellow)

BUZZER INPUT

(Not available on 1030e)

SENSE (White)

CLOCK / D1 (Green)

DATA / D0 (Blue)

+12V (Red)

OV / GND (Black)

RED (Brown)

GREEN (Yellow)

DO NOT CONNECT SENSE (White cable)

BUZZER INPUT

(Not available on 1030e)

NB: Illustrations apply to all MIFARE readers

ACTpro MIFARE Readers Installation Manual

WIEGAND Entry Reader - Wiring

WIEGAND Exit Reader - Wiring

SENSE

CLOCK / D1 (Green)

DATA / D0 (Blue)

+12V (Red)

OV / GND (Black, White)

RED (Brown)

GREEN (Yellow)

BUZZER INPUT

(Not available on 1030e)

SENSE (Blue)

CLOCK / D1 (Green)

DATA / D0

+12V (Red)

OV / GND (Black, White)

RED (Brown)

GREEN (Yellow)

BUZZER INPUT

(Not available on 1030e)

IMPORTANT: To put ACT readers into wiegand mode

connect the SENSE on the reader to 0V/GND.

IMPORTANT: To put ACT readers into wiegand mode

connect the SENSE on the reader to 0V/GND PIN and

DATA/D0 to the SENSE PIN on the controller.

ACTpro MIFARE Readers Installation Manual

Reader Conﬁguration

Operation: ACTpro MIFARE 1030PM / 1040e / 1050e

ACTpro MIFARE readers can operate in sector, serial or reverse serial

mode which is selectable via a jumper. To change the operation mode

power down the reader, change the jumper for the desired operation and

re-apply power.

Operation: ACTpro MIFARE 1030e

The operation of the ACTpro MIFARE 1030e is selectable via cable

conguration. To change the operation power down the reader, change

the Orange and Purple cable for the desired operation and re-apply

power.

Sector Reader

The default sector reader operation reads a numbers encoded into

Sector 1 of the MIFARE cards and fobs. The ACT MIFARE readers can

be programmed to read any specied sector data. See section on reader

re-programming.

Serial and Reverse Serial Reader

When in Serial or reverse serial mode the MIFARE card serial number

(CSN) is read by the reader.

Sector

Serial

Reverse

Serial

Connect Pins 1&2 Connect Pins 2&3 Do NOT connect Jumper

Colour Sector Serial Reverse Serial

Orange 0V 0V Not Connected

Purple 0V Not Connected 0V

ACTpro MIFARE Readers Installation Manual

Reader Re-programming

The ACTpro MIFARE readers will ship from the factory pre-congured to

read ACT MIFARE cards and fobs. The ACT pro MIFARE reader can also

be recongured for serial or reverse-serial by repositioning the jumpers.

(See section on reader conguration)

On sites with an existing installation of MIFARE cards, it may be necessary

to re-program MIFARE readers so that data on the existing MIFARE

cards can be read. The ACTpro MIFARE readers are re-programmed

using a programming card.

The programming card can be generated on site using ACTenterprise

software and an ACTpro USB reader (ACTinstall->Advanced Setup

->card conguration->MIFARE format). You will require the following

information on how the existing cards are encoded before generating

the programming card: Data Format, Data Orientation, Start and End

Byte Position and Read/Write Keys.

To re-program an ACTpro MIFARE reader the programming card must

be presented to the reader after power up and while the LED is Red.

The ACTpro MIFARE will acknowledge the re-programming by playing

an ascending note tune. (Conguration is held in non-volatile memory)

Readers that have been re-programmed may be reset to read ACT

issued MIFARE cards and fobs with an ACT Default Programming Card.

ACTpro MIFARE readers that have been programmed to read non ACT

MIFARE cards and fobs will play a series of ascending notes after being

powered up in addition to the standard beep codes, this is to indicate

that it no longer reads the MIFARE cards and fobs issued by ACT.

Please see the “Application for an ACTpro MIFARE reader programming

card” document for details on obtaining a programming card.

ACTpro MIFARE Readers Installation Manual

Backlight Operation - ACTpro MIFARE 1050e

The ACTpro MIFARE 1050e has backlight illumination of the keypad. The default

operation is for the illumination to be switched on. During installation the back light

operation may be switched off or changed to automatic. In automatic mode the

keypad is illuminated for 20 seconds on a key press or when a card is presented

to the reader.

To change the backlight operation: Firstly power up the reader, the LED on the top

right hand side will cycle through green, blue and red and back to blue, while the

LED is red enter the code below for the required operation. The code must be com-

pletely entered while the LED is red.

• Always on (Default): X014000

• Always Off: X014001

• Automatic: X014008

Note: the backlight operation for the ACTpro MIFARE 1030PM is controlled by

jumpers marked LED.

Buzzer Operation

The Internal buzzer is activated by applying 0V to the Buzz PIN. The buzzer acti-

vates 4 seconds after the 0V is applied and sounds continuously until the 0V is re-

moved (External Buzzer Control not available on the ACTpro MIFARE 1030) reader.

Power On Beep Codes

The Output Data Format and the Sector/Serial Operation of the reader can be de-

termined by the beeps generated by the reader after power is applied. The reader

will generate two sets of beeps, the rst indicating the Output Data Format and the

second set of beeps indicating Sector or Serial Operation. The rst set of beeps will

occur while the LED is Green, the second set of beeps occur half a second later

while the LED is Blue.

First Beep Set Double Beep Sector Reader

Single Beep Serial Reader

Triple Beep Serial Reader (byte reverse)

Second Beep Set Double Beep Clock & Data Output

Single Beep Wiegand 37 bit Output

Note: If the reader has been re-programmed (see next page), then a series of notes

is played after the Second Beep Set, this indicates that the default programming to

read ACT MIFARE cards has been changed.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente