ACTi Q970 Manuale utente
Intercom Camera
Hardware Manual
Q970
2022/03/23
www.acti.com
Hardware Manual
2
Table of Contents
Precautions 3
Safety Instructions ...........................................................................5
Introduction 6
The List of Models ............................................................................6
Package Contents.............................................................................7
Physical Description ........................................................................8
Installing the Camera 9
Step 1: Prepare for Installation........................................................9
Step 2: Mount the Camera ...............................................................9
Step 3: Connect the Camera............................................................9
Step 4: Access the Camera Live View........................................... 10
Cable Connections 11
Connecting a Power Adapter (Optional)....................................... 11
Connecting DI/DO Devices (Optional)...........................................12
Connecting Serial Devices (Optional)...........................................13
Other Accessories 14
How to Install / Remove the Memory Card ................................... 14
How to Remove the Memory Card...............................................14
Accessing the Camera 15
Configure the IP Addresses...........................................................15
Access the Camera.........................................................................19
www.acti.com
Hardware Manual
3
Precautions
Read these instructions
Read all the safety and operating instructions before using this product.
Heed all warnings
Adhere to all the warnings on the product and in the instruction manual. Failure to follow the
safety instructions given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
ACTi and ACTi logo are registered trademarks of ACTi Corporation. All other names and
products used in this manual are registered trademarks of their respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. ACTi will not be held responsible for any
typographical or technical errors and reserves the right to make changes to the product and
manuals without prior notice.
www.acti.com
Hardware Manual
4
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.
www.acti.com
Hardware Manual
5
Safety Instructions
Cleaning
Disconnect this product from the power supply before cleaning.
Accessories and Repair Parts
Use only the accessories and repair parts recommended by the manufacturer. Using other
attachments not recommended by the manufacturer may cause hazards.
Installation
The device front panel is waterproof, however, installers must ensure that water will not
penetrate through any gap on the surface wall which may leak through to the cable
connections or the main board.
The device is designed to be flush mounted on the wall. Surface mounting the device or
mounting it in other ways may affect its waterproof capability.
Install other devices (such as PoE injector, alarm, etc.) that will be used with the camera in a
dry place protected from weather.
Servicing
Do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the product.
3) If the inner parts of product have been directly exposed to rain or water.
4) If the product does not operate normally even by following the operating instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as improper
adjustment of other controls may result in damage, and will often require extensive work
by a qualified technician to restore the product to its normal operation.
Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine if the product is in proper operating condition.
www.acti.com
Hardware Manual
6
Introduction
The List of Models
This hardware manual contains the following models:
Q970
2MP, Intercom, Basic WDR, Superior Low Light Sensitivity
www.acti.com
Hardware Manual
7
Package Contents
Check if the camera package comes with the following items.
Camera
Screws and Plugs
Drill Template
10-Pin Terminal Block
6-Pin Terminal Block
Quick Installation Guide &
Warranty Card
Drill Template
Warranty Card
www.acti.com
Hardware Manual
8
Physical Description
Item
Description
1
Lens
Provides a wide viewing angle
2
Speaker
The built-in speaker allows the user to hear the person on the
receiving end.
3
Push Button
Functions as the emergency button. Push to notify and speak to
personnel in charge.
4
Built-in Microphone
The built-in microphone allows the user to speak to the person on
the receiving end.
5
Audio Input /
Digital Input /
Serial Connector
Connects external input devices such as audio and digital input
devices. Serial devices that use RS-485 protocol can also be
connected here. See Cable Connections on page 11.
6
Power LED
Lights red when the camera is powered up.
7
Memory Card Slot
Insert a memory card (not included) into the slot for local recording
purposes. See How to Install / Remove the Memory Card on
page 14 for more information.
NOTE: Supports only microSDHC and microSDXC cards.
8
Ethernet Port
Connects to a network using an Ethernet cable.
9
Reset Button
Restores the factory default settings of the camera. To reset the
camera, while the power is on, press and hold the Reset Button for
at least 5 seconds or until the Power LED goes off.
10
Digital Output
Connects to digital output devices, such as an alarm trigger, etc.
See Cable Connections on page 11 for information.
www.acti.com
Hardware Manual
9
Installing the Camera
The intercom camera is designed to be directly flush mounted on the wall. The front panel is
visible and will be aligned on the surface of the wall. This installation requires access to the
back of the surface.
Step 1: Prepare for Installation
1. Attach the bundled drill template sticker on the target installation surface.
2. Drill the hole where the camera body will be mounted. Note that the connectors are on the
bottom side of the camera; make sure that side can be accessed from the back of the
surface.
3. Drill the screw holes, as needed.
4. Remove the drill template.
Step 2: Mount the Camera
1. Mount the camera body through the hole.
2. Attach the four (4) screws to secure the camera on the surface.
NOTE: The device front panel is waterproof. However, you must ensure to seal and
protect water from entering through any gap on the surface wall which may flow to the
cable connections on the bottom of the camera.
Step 3: Connect the Camera
1. Connect the other end of the network cable from the camera to the network. Connect all
other devices, if any.
2. Connect the other end to a switch or injector. Then, connect the switch or injector to a
network or PC and a power source. See Power-over-Ethernet (PoE) example connection
diagram below.
Network
AC Power
Source
PoE Injector /
PoE Switch
Power Cable
Ethernet Cable
Ethernet Cable
(Data + Power)
Ethernet Cable
(Data)
Camera
www.acti.com
Hardware Manual
10
In case of using a non-PoE switch, power up the camera using a power adapter (not
supplied). See Connecting a Power Adapter (Optional) on page 11 for more
information.
3. As needed, connect and power up other devices, such as digital input/output, audio, or
serial device. See Cable Connections on page 11 for more information on connecting
other devices.
Step 4: Access the Camera Live View
See Accessing the Camera on page 15 for more information.
Indice
Altri manuali ACTi Macchina fotografica digitale
ACTi
ACTi A950 Manuale per l'uso e la cura
ACTi
ACTi MGB-102 Manuale utente
ACTi
ACTi MPEG-4 Manuale utente
ACTi
ACTi B57 Manuale utente
ACTi
ACTi C11W Manuale utente
ACTi
ACTi Q950 Manuale utente
ACTi
ACTi KCM-5111 Manuale utente
ACTi
ACTi PMON-2000 Manuale utente
ACTi
ACTi KCM-7911 Manuale utente
ACTi
ACTi KCM-3911 Istruzioni operative
