ACTi ACM-1100 Series Manuale utente
IP Indoor CMOS Bullet Camera
ACM-1100 series
Ver. 081208
Quick Installation Guide
0-1
0Getting Started
1.1 PACKAGE CONTENTS
ACM-1100 series Power Adaptor (Option)
(DC12V / PoE)
The bracket is not included
Product CD Terminal Block for Power
Warranty Card
1
0-2
1.2 PHYSICAL DESCRIPTION
1. Audio Input / Output
The IP Indoor CMOS Bullet Camera supports audio input and
output with earphone jack
2. Power Input
If your power input is DC12V. Please follow the description on
the connector to connect to power.
3. Ethernet Port
The IP Indoor CMOS Bullet Camera connects to the Ethernet via
a standard RJ45 connector. Supporting NWAY, this IP Indoor
CMOS Bullet Camera can auto detect the speed of local network
segment (10Base-T/100Base-TX Ethernet).
4. Reset Button
PIN
NAME
DESCRIPTION
1
12V
DC Power Input
2
GND
Ground Pin
0-3
Step 1: Switch off IP Indoor CMOS Bullet Camera by
disconnecting the power cable
Step 2: Press and continue to hold the Reset Button. Reconnect
the power cable while continuing to hold the reset button.
Step 3: Keep holding the reset button depressed around 6 seconds,
release the reset button. The unit will start up with factory default
settings.
5. Analog Video Output
The IP outdoor rugged dome supports one channel analog video
output.
0-4
1.3 BASIC CONNECTIONS
Follow the procedures below to connect the IP Indoor CMOS Bullet
Camera to the respective apparatuses.
1. Connect an analog monitor to IP Indoor CMOS Bullet Camera video out
(BNC connector).
2. Connect the power adaptor to IP Indoor CMOS Bullet Camera
3. Connect IP Indoor CMOS Bullet Camera’s ethernet port to an Ethernet
(RJ45 connectors). If your IP Indoor CMOS Bullet Camera has PoE
built-in, you can regard it as a PD and connect it directly to a PSE device
like PoE switch.
4. Connect a PC to the Ethernet hub (RJ45 connectors)
1
NOTE: You may find a support package for help you getting familiar
with PoE. Please visit our web site, and get the support document
TS-00040.
1-5
1Quick Tour
This section guides you with a quick tour on this IP Indoor CMOS Bullet Camera.
2.1 Configure this IP Indoor CMOS Bullet Camera
2.1.1 Make sure network environment
Default IP of this IP Indoor CMOS Bullet Camera is 192.168.0.100. Please make sure
this IP Indoor CMOS Bullet Camera and your PC are on the same network segment
before running the installation.
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)
1-6
2.1.2 Open Internal Explorer with IP address
NOTE: If your web browser is earlier than IE6, then download IE6 is
recommended.
NOTE: This IP Indoor CMOS Bullet Camera default IP address is set to
192.168.0.100
2.1.3 Login with default administrator’s account & password
NOTE: Default administrator account is set to Admin, password is set to
123456, and click button.
1-7
2.1.4 Preview the video
2.1.5 Set the new IP address
1-8
*IP Address : The default IP address is 192.168.0.100.
*Subnet Mask : The default subnet mask is 255.255.255.0
*Click button
NOTE: In your Client PC, please make sure the setting of Network
Connections Type is set to Auto Negotation, since this IP Indoor CMOS
Bullet Camera follows MII standard. Otherwise, you might not see the live
image.
IMPORTANT: After the IP address is changed, please record this IP
address. There’s no way to connect to the IP Indoor CMOS Bullet
Camera if user forgets the new IP address.
2.1.6 Check Default Video Setting
NOTE: Please make sure the TV Input (NTSC / PAL) is meet your
requirement, and click button.
2.1.7 Click Save Reboot to restore all settings and please wait about 30 seconds
for system reboot.
Indice
Altri manuali ACTi Telecamera di sicurezza
ACTi
ACTi VMGB-351 Manuale utente
ACTi
ACTi TCM-1011 Istruzioni per l’uso
ACTi
ACTi ACM-3401 Series Istruzioni per l’uso
ACTi
ACTi KCM-5511 Istruzioni per l’uso
ACTi
ACTi KCM-3911 Manuale utente
ACTi
ACTi D52 Istruzioni per l’uso
ACTi
ACTi D31 Manuale utente
ACTi
ACTi ACM-360 Series Istruzioni per l’uso
ACTi
ACTi ACM-3300 Istruzioni per l’uso
ACTi
ACTi ACM-1430 series Manuale utente
