Ada Ez Pro Manuale utente
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
1 of 12
Quick-Start Guide
ADA EZ Pro
Pull-Side Operator Quick-Start Guide
700302
Rev. A, 0/ 4/ 2
ADAQS01
PULL-SIDE APPLICATION
(RIGHT HAND DOOR SHOWN)
PULL-SIDE APPLICATION
(LEFT HAND DOOR SHOWN)
This m nu l provides quick-reference instructions for inst lling nd oper ting the pull-side ADA EZ swing
door oper tor. Prior to performing these instructions thoroughly review the following inform tion in
document number 70002, “ADA EZ Pro Inst ll tion nd Oper ting Instructions:”
•
System Description
•
Det iled oper tor progr mming instructions
•
Prerequisites
•
Repl cing the b ttery p ck fuse
•
Prec utions
•
Customizing the oper tor settings
•
Controls nd indic tors
•
Inst lling door dec ls
•
Inst lling the option l plug-in tr nsformer
•
Det iled closeout instructions
•
Inst lling the pushbutton switches
•
Wiring
•
Linking the RF pushbuttons
•
Repl cement p rts
• Troubleshooting recommend tions • Adjusting door spring tension
To obt in the l test m nu l nd templ te revisions or to view inst ll tion nd progr mming videos
go to www.ADAEZ.com. For technic l support c ll (877) 232-3987.
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
2 of 12
Quick-Start Guide
TABLE OF CONTENTS
1.1 Inst lling the Oper tor Mounting Templ te ................................................................................................. 2
1.2 Mounting the Door Shoe .............................................................................................................................. 3
1.3 Inst lling the Oper tor Mounting Br cket nd Cover .................................................................................. 5
1.4 Inst lling the Door Oper tor ........................................................................................................................ 6
1.5 Inst lling the Door Arm ............................................................................................................................... 6
1.6 Inst lling the Option l Plug-In Tr nsformer ................................................................................................ 8
1.7 Progr mming the Oper tor......................................................................................................................... 11
1.8 Initi lizing the Remote Control .................................................................................................................. 12
. Installing the Operator Mounting Template
1.1.1 If the door is n luminum storefront door, EXAMINE the top r il nd, when drilling the mounting
holes, ENSURE the following:
• Do not drill into the top r il web
• Do not drill into the r il-to-stile tie rod(s)
• Do not drill into the r il-to-stile junction
1.1.2 Refer to Figure 1, nd ALIGN the oper tor mounting templ te to the centerline of the butt hinge,
center pivot, or offset pivot s pplic ble.
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
3 of 12
.2 Mounting the Door Shoe
1.2.1 If the door fr me is steel or luminum nd rivnuts must be inst lled, refer to Figure 2 nd
PERFORM the following:
. Using
25
/
64
″ drill, DRILL the door rm pivot br cket holes.
b. Using rivnut tool, INSTALL the ¼-20 steel rivnuts.
c. INSTALL nd TIGHTEN the two (minimum) ¾″ (19.05 mm) socket he d c pscrews with
w shers) securing the door rm pivot br cket to the underside nd f ce of the fr me he der.
1.2.2 If the door fr me is wood, refer to Figure 2 nd PERFORM the following:
. Using
5
/
32
″ (3.97 mm) drill, DRILL the door rm pivot br cket pilot holes.
b. INSTALL nd TIGHTEN the three #14 x 1 ¼″ wood screws (minimum) securing the door
rm pivot br cket to the underside nd f ce of the fr me he der.
Figure . Installing the Operator Mounting Template
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
4 of 12
Figure 2. Mounting the Door Shoe
ADAQS03
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
5 of 12
.3 Installing the Operator Mounting Bracket and Cover
CAUTION
For light-duty or hollow-core doors with insufficient top r il blocking, through bolts or sex nut nd bolts
re required to securely tt ch the oper tor mounting br cket.
To ensure proper inst ll tion, the oper tor must be f stened with at least four f steners. For he vier doors
more f steners re recommended.
1.3.1 If the door is luminum nd rivnuts must be inst lled, refer to Figure 3 nd PERFORM the
following:
. Using
25
/
64
″ drill, DRILL the mounting br cket holes.
b. Using rivnut tool, INSTALL the ¼-20 steel rivnuts.
c. INSTALL nd TIGHTEN the four (minimum) ¾″ (19.05 mm) socket he d c pscrews (with
bl ck oxide w shers) securing the oper tor mounting br cket.
1.3.2 If the door is wood, refer to Figure 3 nd PERFORM the following:
. Using
5
/
32
″ (3.97 mm) drill, DRILL the mounting br cket pilot holes.
b. INSTALL nd TIGHTEN the four #14 x 1 ¼″ wood screws (minimum) securing the oper tor
mounting br cket.
1.3.3 ADJUST the br cket
so th t there is
5
/
8
″
(16mm) sp ce between
the top of the br cket
nd the top of the door.
1.3.4 TIGHTEN the socket
he d c pscrews
securing the mounting
br cket to the door.
1.3.5 Using
7
/
16
″
(11.112mm) box
wrench or l rge
djust ble wrench,
TIGHTEN the
oper tor mounting pins
into the upper thre ded
holes in the mounting
br cket.
1.3.6 INSTALL the oper tor
mounting br cket
cover over the oper tor
mounting br cket.
Figure 3. Installing the Operator Mounting Bracket and Cover
MOUNTING BRACKET COVER
OPERATOR
MOUNTING PINS
FASTENERS
(FOUR MINIMUM)
5/8
ADAQS04
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
6 of 12
.4 Installing the Door Operator
1.4.1 REMOVE the dress cover from the oper tor.
WARNING
To void in dvertent ctiv tion of the oper tor during connection of the door rm, the b ttery p ck should
not be inst lled until after the door rm is connected.
1.4.2 Refer to Figure 4, nd, with the b ttery p ck f cing the j mb, POSITION the oper tor onto the
oper tor mounting pins. ENSURE oper tor does not slide off the mounting pins.
1.4.3 INSTALL nd TIGHTEN the two ¼-20 X 1½″ socket he d c pscrews securing the oper tor to the
oper tor mounting pins.
.5 Installing the Door Arm
1.5.1 Refer to Figure 5, nd
INSTALL sh ft extension
onto oper tor sh ft.
1.5.2 TIGHTEN set screw securing
sh ft extension to oper tor
sh ft.
Figure 4. Installing the Operator
ADAQS05
Figure 5. Installing the Shaft Extension
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
7 of 12
1.5.3 Refer to Figure 6, nd ADJUST door rm length to 8
1
/
16
″ (204.77 mm).
1.5.1 Refer to Figure 7, nd, with the door rm coupling screws f cing up, POSITION the l rger end of
the door rm onto the oper tor output sh ft.
CAUTION
The door rm coupling is two-piece t pered coupling. To dr w the coupling h lves together evenly the
three door rm coupling screws must be tightened evenly (one qu rter turn t time) until fully tight.
1.5.2 While m int ining the door
rm position, TIGHTEN the
door rm coupling screws
evenly (one qu rter turn t
time) until fully tight.
1.5.3 INSTALL the
5
/
16
– 18 fl t
he d screw into the door shoe
mounting br cket to secure
the door rm.
1.5.4 CYCLE the door sever l
times, nd ENSURE th t the
door opens nd closes
smoothly.
1.5.5 SLIDE the dress cover onto
the oper tor.
1.5.6 CONNECT the b ttery p ck
connector plug to the
oper tor.
1.5.7 SLIDE the b ttery p ck onto
the oper tor, nd ENSURE
th t the b ttery p ck wires
will not interfere with the
oper tor cover.
Figure 6. Adjusting the Door Arm Length
Figure 7. Installing the Door Arm
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
8 of 12
.6 Installing the Optional Plug-In Transformer
NOTE
If possible, the tr nsformer wiring should be routed g inst the door trim molding.
1.6.1 ROUTE tr nsformer wiring to 110-VAC outlet, but do not plug tr nsformer into the outlet.
NOTE
An option l plug-in tr nsformer is recommended in inst ll tions where the utom tic door-opening fe ture
will be used frequently. The option l plug-in tr nsformer is REQUIRED for inst ll tions where Power
Close nd/or Push nd Go fe tures re en bled.
1.6.2 Refer To Figure 8, nd ROUTE wires through rmored c ble end links. MOUNT the door cord end
links s follows:
• MOUNT one end link in the re behind or next to the b ttery p ck.
• MOUNT the other end link on or next to the door fr me.
Figure 8. Routing Wires through Cable End Links
SEE DETAIL A
ROUTE WIRE INTO
END LINK FROM
FRONT
ROUTE WIRE THROUGH
EXIT AT BOTTOM
SIGNAL INPUT
CHARGER INPUT
GROUND (COMMON) INPUT
24VDC (POSITIVE) INPUT
EZ0 1
DETAIL A
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
9 of 12
1.6.3 Refer to Figure 9, nd PLUG connector into recept cle on b ttery p ck.
1.6.4 Refer to Figure 10, nd VERIFY th t the LED indic tor lights GREEN.
Figure 9. Plugging the Connector into the Receptacle
CONNECTOR COVER
CONNECTOR PLUG
CONNECTOR RECEPTACLE
EZ0 0
Figure 0. Verifying that the LED Illuminates
LED INDICATOR
ADAEZ 0
700302
Rev. A, 10/14/12
© 2012 ADA EZ. ALL RIGHTS RESERVED.
10 of 12
1.6.5 Refer To Figure 11, nd INSTALL recept cle cover onto b ttery p ck.
Figure . Plugging the Receptacle Cover onto the Battery Pack
EZ0 2
Altri manuali per Pro
1
Indice
Altri manuali Ada Ez Sistema di apertura della porta
