Adata XPG 3.5" Manuale utente
User Manual
V090513 - 1 -
User Manual
A-DATA XPG 3.5” SSD RAID Enclosure
Description:
The RAID Enclosure is a complete RAID solution through the use of
two 2.5" SATA hard disks mounted on one mini 3.5" form factor drive
cage. It is used as a standard 2.5" SSD/HDD with mirroring capability
(RAID 1). By mirroring technique, it maintains data in two disk drives
simultaneously and securely. If one drive fails, it automatically switches
operations to the functional drive and after changed a new hard drive
the data is mirroring back.
Features:
* Interface:
SATA-I/II
* LED indication for Working and Failure.
* The dimensions match exactly as a standard 3.5" bay.
* Energy saving on using 2.5” SSD or HDD.
* For the use on desktop, server case, rack mount chassis that is
with 3.5” form factor space.
User Manual
V090513 - 2 -
* Complies with SATA-I, SATA-II interface. Maximum transfer
rate up to 1.5Gbps for SATA-I and 3.0Gbps for SATA-II.
* SSD Auto Eject when you open the front cover.
* Aluminum material, best heat sink.
* Dimension: 148.2 x 101.7 x 25.8mm (L*W*H)
* Weight: 0.23 kg
Accessory List:
1.
3.5” RAID Enclosure * 1
2. User Manual * 1
3. 7 pin SATA Cable * 1
4. Screws Bag * 1 (With 4 screws)
Front Panel:
Picture A
User Manual
V090513 - 3 -
A1 : SSD/HDD 0 Access LED
A2 : Power LED
A3: SSD/HDD 1 Access LED
A4 : Upper cover & SSD/HDD extractor
A5 : Lower cover & SSD/HDD extractor
A6 : Upper SSD/HDD Safety Lock (Push rightward to open & push
leftward to lock)
A7 : Push the rise high position to open the upper & lower cover
A8 : Lower SSD/HDD Safety Lock (Push rightward to open & push
leftward to lock)
Rear Panel:
B1 : SATA 15pin power connector
B2 : SATA 7pin data connector for SSD/HDD 0
B3 : RAID mode configuration DIP switch
B4 : Change mode button
User Manual
V090513 - 4 -
LED Table
Check the following to see the LED Indicator Table.
SSD/HDD 0 Access LED Indicator (A1)
Action Message Color
Light On Hard Drive 0 Installed Blue
Light Off Hard Drive 0 uninstalled No
Light On Hard Drive 0 Fail Red
Flash Hard Drive 0 Access Blue
Power LED Indicator (A2)
Light On Power is ON Blue
Light Off Power is OFF No
SSD/HDD 1 Access LED Indicator (A3)
Light On Hard Drive 1 Installed Blue
Light Off Hard Drive 1 uninstalled No
Light On Hard Drive 0 Fail Red
Flash Hard Drive 1 Access Blue
The following is the special case LED table.
LED Indicator in special case
Message LED Color / Action
Both Hard Drives installed
without cable connection A1/A2 Blue/Light on
The following is the LED Indicator in RAID modes.
RAID Mode LED Indicator
RAID
Mode Message LED Color / Action
RAID 1 Reading A1 Blue/Flash
RAID 1 Writing A1/A3 Blue/Flash
RAID 1 SSD/HDD 0 Rebuilding A1 Blue & Red/Flash
RAID 1 SSD/HDD 1 Rebuilding A3 Blue & Red/Flash
JBOD SSD/HDD 0 Access A1 Blue/Flash
JBOD SSD/HDD 1 Access A3 Blue/Flash
RAID 0 Access A1/A3 Blue/Flash
User Manual
V090513 - 5 -
Safety Lock
Upper SSD/HDD Safety Lock & Lower SSD/HDD Safety Lock. Push
rightward to open & push leftward to lock. See Picture C.
Picture C
SSD/HDD Installing:
Open the upper & lower cover and put the SSD/HDD into the cage.
You can install one SSD/HDD or two SSDs/HDDs.
Picture D
User Manual
V090513 - 6 -
Hardware Installation Procedures
Please follow below procedures to complete the hardware installation:
1
) Open the package, take out the product, make sure the product is
brand new and all the necessary parts are included (Please check
with Accessory List).
If damage or shortage occurred, please contact your distributor
or where you bought.
2) Unlock the upper and lower covers (see picture C), push the lock
rightward and open the two covers and then, put the two 2.5" SATA
SSDs/HDDs into the box (See Picture D).
3) After both SSDs/HDDs installed, push both covers back like picture
C and then, push the lock button leftward to lock both covers to
secure the SSDs/HDDs inside properly.
4) Then, mount the 3.5” enclosure on the 3.5” space using the included
screws to mount it on the device (desktop, case… etc.) and make all
the cable connected properly and it is ready for use.
5) See the drawing of the two ways to mount the 3.5” enclosure on the
Device (See Picture E).
User Manual
V090513 - 7 -
6) There are 2 ways to mount the 3.5”enclosure on the device:
-- Picture F-1) Mount it on the floppy drive bay
-- Picture F-2) Mount it inside the case
7) Connect the 3.5” enclosure with PC via 15pin SATA power cable
(from Power Supply) and 7pin SATA cable (using included cable).
(See Picture F-3)
Picture E
User Manual
V090513 - 8 -
Picture F-1 Picture F-2
Picture F-3
User Manual
V090513 - 9 -
Set the RAID mode by the DIP Switch:
DIP Switch Table
When you want to set any RAID mode as above table, please follow
below steps:
Step 1: Power off
Pull out the Power Cable before you change the Dip Switch.
Step 2: Ready to Reset the RAID Setting
Change the Dip Switch to
Normal Mode
position to be ready for reset.
Step 3: Reset Complete.
Press
CHANGE MODE
button for 5 seconds and Plug on the Power
Cable to activate the RAID setting at the same time.
RAID Config
RAID Status 1 2
Normal OFF OFF
RAID 1 OFF ON
JBOD ON OFF
RAID 0 ON ON
User Manual
V090513 - 10 -
Step 4: Ready to change the RAID Mode
Pull off the Power Cable and change the Dip Switch to the RAID Mode
you want.
Step 5: Activate the RAID Mode
Press
CHANGE MODE
button for 5 seconds and Plug on the Power
Cable to activate the RAID setting at the same time.
Note:
A) If present mode is in Normal Mode, users don’t need to reset.
B) Users should wait at least 5 seconds to activate the RAID Mode
and then release the Change Mode button
C) After the selected RAID is built ready, then, to partition/format
the RAID-built SSDs/HDDs. After SSDs/HDDs being formatted,
they are ready to be used.
Altri manuali per XPG 3.5"
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Adata Allegato
