Additel ADT 680 Manuale utente
Additel Corporation
User's Manual
[.：]Version No 1612V14
ADT 680 Digital Pressure Gauge
Digital Pressure Gauge
CONTENTS
1. Introduction
2. Basic structure
3. 2
4. Display 3
5. Start-up screen
6. Menu setup and configuration
7. Calibration
8. Troubleshooting
Specifications 15
1 Warning 19
2 FCC Declaration of Conformity 20
3 Battery installation 22
4 Ordering information 23
5 Appendix 24
……………………………………………………………………………………………………………1
…………………………………………………………………………………………………………1
…………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………
…………………………………………………………………………………………………………3
………………………………………………………………………………………4
………………………………………………………………………………………………………………8
………………………………………………………………………………………………………12
. …...……………………………………………………….………………………………………………
1 . ………………………………………………………………………………………………………………
1 . ……………………………………………………………………………………
1 . …………………………………………………………………………………………………
1 . ………………………………………………………………………………………………
1 . ………………………………………………………………………………………………
Keypad
9. ….……….………………………………………………………………………………………………Custom Unit Entry 13
10
I– Data logging
Model
Pressure Port Type
The ADT digital pressure gauge is a rugged wireless data logging pressure gauge that can log in real
time or data which can be stored and downloade later via wireless communication The compact industrial
design and advanced technology makes the ADT as an ideal pressure measurement tool The ADT
combines a variety of accuracy levels with a robust IP water and dust proof casing It can
either as a pressure reference or an applications where high accuracy is required
680
, .
680 . 680
67 - - .
.
d
be used
measurement
Screen
keypad
Pressure Range
Sensor Cavity
Pressure Port
Introduction
1
Rubber boot
units zero
M20X1.5
psi
1
Digital Pressure Gauge
Back Plate Screws
Label Plate
Basic structure
2
units zero
Digital Pressure Gauge
2
keypad
3
Pressure display:
Menu setup mode:
Push the button Pressure zero->
Push and hold the button Lock Unlock
Key
-> /
Push the button Enter Make selection-> /
Pressure display:
Menu setup mode:
Push and hold the button Turns power
on off
->
/
Push the button Go back Cancel-> /
Pressure display:
Menu setup mode:
Push the button Switch engineering units->
Push and hold the button Enter menu
setup mode
->
Push the button Move forward
through menus /
Highlight shift right
->
Pressure display:
Menu setup mode:
Push the button Backlight on off-> /
Push and hold the button Min Max
value
-> /
Push the button Move backward
through menus
Number incrementing
->
/
Engineering units
Battery bar graph
5 digit display
Percentage bar graph
Menu icons
Wireless signal icon
Data logging icon
Keypad lock icon
Absolute pressure
Full screen display Software version Upper range value
Live pressure display Lower range value
Digital Pressure Gauge
3
Display
4
Start-up screen
5
6.1 Menu structure
03
04
10
1ORD
15
30
45
60
ON
15
30
45
60
OFF
90
120
01.
10.
15
03.
Backlight does not auto off
Low pass first order filter
(only active for 0.1 readings/second)
Average filter
Backlight auto off time
unit second(: )
Gauge does not auto off
Delay time before auto off
unit minute(: )
Pressure reading interval
unit second(: )
Year
Hour min:
Second
Month day:
RTC
Rate
Auto off
Backlight time
Average measure
Digital Pressure Gauge
4
Menu setup and configuration
6
OFF No filter
1.off
4ct01.-/
2.chan
1cap.
3 del.
2 send.
5ct01.-/
4 gap.
1.bat
5dp01.-/
2temp.
4fact.
3 leak.
51.-az
1cal.
3clr.
2c00.-
4 abs.
in 20(℃)HO₂
in 60(℉)HO₂
mm 20(℃)HO₂
mm 15(℃)HO₂
ft 60(℉)HO₂
Set factor for custom units Refer to specification()
Wireless channel CH 01 15( -~)
Memory capacity status
Upload data
Delete all data, password is “218”
Logging Interval s s(0001 -9999 )
Keep the logging status after restart
1 means YES, 0 means NO)(
Battery voltage
Environment temperature support(℃、℉)
Absolute pressure zeroing Absolute-
Auto zero
Cancel recover calibration data/
Cancel pressure zero
Pressure leak test
Restore factory settings, “password is 218”
Device address 001 112(~)
Keep the wireless status after restart
( 1 means YES, 0 means NO)
6off.
Start Stop logging/
3 addr.
Wireless on off/
Tare setting Refer to specification Gauge()-
Extended units
Calibration
Utilities
Data logging
Wireless
ft 4(℉)HO₂
Overpressure status: 1 means YES, 0 means NO.
Digital Pressure Gauge
5
View overpressure records ( )Refer to specification
Calibration See calibration section on page(8)
6.2 Menu operation
6.2.1 Enter Return/
Push and hold button in the pressure display mode to enter menu setup mode.
Push button in menu setup mode to return to previous menu.
Example:
Pressure display
Menu1
Aver ge measure(a )
Push and hold
Push
6.2.2 Switch menu item
Push and button to move forward or backward through the menus:
units
units
units
Digital Pressure Gauge
6
Example:
Move menu Average measure forward to menu Backlight setup1( ) 2( )
Move menu Aver ge measure backward to menu1( a ) 10( )Extended units
6.2.3 Submenu setup
Push to access submenu setup, push or to view options then push to select
an option or push to recover former option
,
,.
Average measure
03
04
10
1ORD
OFF
05
06
07
08
09
Example:
The current option will blink
save
cancel
units
zero
units
zero
zero
zero
units
Digital Pressure Gauge
7
Indice
