Adept technology GRouter4 Manuale utente

GRouter4

Single Port 709.1 /852 LON/IP Router

User Guide

4.12

2011/03/19

Document Revision 4.14.1

Printed in USA.

Version 4.14, March 2011.

is document, the associated soware, and the associated online documentation are the

property of Adept Systems, Inc. and are loaned to the user under the terms of the End User

License Agreement. No title to or ownership of the soware described in this document or any of

its parts is transferred to customers. No part of this document may be reproduced or transmitted

in any form or by any means without the express written permission of Adept Systems, Inc.

Unauthorized copying or use of the soware or any associated materials is contrary to the

property rights of Adept Systems, Inc. and is a violation of state and federal law. is material

must be returned to Adept Systems upon demand.

Disclaimer:

Adept Systems makes no representations or warranties regarding the contents of this document.

Information in this document is subject to change without notice and does not represent a

commitment on the part of Adept Systems, Inc.

Trademarks:

GadgetStack and the Adept Systems Logo are registered trademarks of Adept Systems, Inc.

GRouter, GRouter4, GR4, GRouter3, GR3, GNode, GNode3, GN3, GRN3, GadgetNode,

GadgetNIC, and GadgetTek are trademarks of Adept Systems, Inc.

All other product and company names are trademarks or registered trademarks of their respective

holders.

Contact Information:

Adept Systems Incorporated

242 East 600 North

Lindon, Utah 84042-1662 USA

Voice: 801.766.3527

Fax: 801.766.3528

Web: www.adeptsystems.com

Email: info@adeptsystems.com

-2-

Table of Contents

1. Overview ...................................................................................................7

1.1. Introduction ...........................................................................................7

1.2. Conguration Parameters .....................................................................9

1.3. Modes of Operation ............................................................................10

1.3.1. Manual Mode..................................................................................10

1.3.2. Normal Mode .................................................................................10

1.4. Applications of the GRouter Device....................................................10

1.4.1. Multi-site building automation networks.....................................10

1.4.2. IP backbones for LON traﬃc aggregation ....................................11

1.4.3. Roaming Connections ...................................................................12

1.5. IP Addressing Modes ...........................................................................12

1.6. System Requirements...........................................................................14

1.6.1. System Requirements.....................................................................14

1.6.2. Button, Indicators, and Connectors for GRouter ........................15

1.6.3. Wiring .............................................................................................16

2. Web Conguration..................................................................................17

2.1. Default IP Conguration.....................................................................17

2.1.1. Ethernet ..........................................................................................17

2.1.2. WiFi (802.11b)................................................................................18

2.1.3. WiFi Setup in Windows XP ...........................................................20

2.2. Establishing a Connection (Ethernet or WiFi)...................................21

2.2.1. Ping to Verify..................................................................................21

2.2.2. User Name and Password ..............................................................21

2.3. Restoring Factory Defaults ..................................................................22

2.3.0.1. Basic Procedure........................................................................22

2.4. Web Conguration Parameters...........................................................23

2.5. Status Page ............................................................................................24

2.6. Router Setup .........................................................................................29

2.6.1. Normal Mode Router Setup...........................................................29

2.6.2. Manual Mode Router Setup...........................................................34

2.7. IP Setup Page ........................................................................................35

2.8. WiFi Setup Page....................................................................................37

2.9. 709 Setup Page......................................................................................39

2.9.1. Node Parameters ............................................................................39

2.9.2. Forwarding Tables..........................................................................40

-3-

2.10. Channel List Page.................................................................................43

2.10.1. Normal Mode Channel List Page ..................................................43

2.10.2. Manual Mode Channel List Page ..................................................45

2.11. Device Detail Page................................................................................47

2.12. Diagnostics Page...................................................................................49

2.13. DDNS Setup Page.................................................................................51

2.14. Contacts Page .......................................................................................52

3. Optional Features....................................................................................53

3.1. 852 to 852 Bridging Router Mode .......................................................53

3.2. Bridging Router Setup .........................................................................53

3.2.1. Router Setup Page ..........................................................................53

3.2.2. 709 Setup Page................................................................................56

3.2.3. Bridging Router Mode Channel List Page....................................56

3.3. Redundant Twin Mode ........................................................................59

3.3.1. Denitions ......................................................................................61

3.3.2. Status SNVT ...................................................................................61

3.3.3. Alarm SNVT...................................................................................62

3.3.4. Status Report UNVT......................................................................62

3.4. Twin Setup Page ...................................................................................63

3.5. Twin Mode Status Page ........................................................................67

4. Network Integration and Management...................................................69

4.1. Manual Mode Example ........................................................................69

4.2. Normal Mode With i.LON Conguration Server Example...............69

4.3. Communicating With Lonmaker With IP Interface..........................70

4.4. Commissioning GRouter Device With LonMaker.............................71

4.5. NAT Router Example ...........................................................................73

4.6. DDNS Router Example ........................................................................74

4.7. Redundant Twin Mode Example.........................................................75

4.8. Conguring with the Coactive Router-LL..........................................79

4.8.1. Manual Mode..................................................................................79

4.8.2. Normal Mode With Router-LL Conguration Server .................80

5. FTT-10 XCVR LonTalk Network Termination .......................................81

6. Firmware Upgrade Instructions..............................................................82

6.1. Upgrading Application Firmware Example........................................84

6.2. Upgrading Bootloader Example..........................................................86

-4-

List Of Figures

Figure 1.1: Network Layers...................................................................................................8

Figure 1.2: Network Connector Types and Associated Layers...........................................8

Figure 1.3: CN to IP Router/Gateway Architecture............................................................9

Figure 1.4: GRouter 3 Architecture......................................................................................9

Figure 1.5: Multi-site building automation network with internet connectivity............11

Figure 1.6: Example Hybrid Network................................................................................11

Figure 1.7: Example WiFi Ad Hoc Network......................................................................12

Figure 1.8: Unicast ..............................................................................................................13

Figure 1.9: Multicast ...........................................................................................................13

Figure 1.10: Front terminal block detail with standard connector..................................16

Figure 1.11: Front terminal block detail with optional pluggable connectors................16

Figure 2.1: Ethernet setup with hub or switch ..................................................................17

Figure 2.2: Ethernet with direct connect crossover cable.................................................18

Figure 2.3: WiFi setup with access point and Ethernet connection to host computer ...18

Figure 2.4: WiFi setup with ad hoc bridge and Ethernet connection to host computer.19

Figure 2.5: WiFi setup with ad hoc WiFi card on PC........................................................19

Figure 2.6: WiFi setup with access point and WiFi card on PC .......................................19

Figure 2.7: User Name and Password Authentication ......................................................22

Figure 2.8: Status Page ........................................................................................................25

Figure 2.9: Status Page with Bridge and Twin Mode Enabled..........................................26

Figure 2.10: Router Setup Page ..........................................................................................29

Figure 2.11: Safe to Power Down Page ..............................................................................33

Figure 2.12: Unsafe to Power Down Page..........................................................................33

Figure 2.13: Time's Up........................................................................................................33

Figure 2.14: Reboot Page ....................................................................................................34

Figure 2.15: IP Setup Page..................................................................................................35

Figure 2.16: 709 Side B Setup Page Main Section .............................................................39

Figure 2.17: 709 Side B Setup Page Main Section .............................................................39

Figure 2.18: Subnet Forwarding Table...............................................................................41

Figure 2.19: Group Forwarding Table ...............................................................................42

Figure 2.20: Channel List Page...........................................................................................43

Figure 2.21: Channel List Page with Multiple Members ..................................................44

Figure 2.22: Channel List Page in Manual Mode ..............................................................46

Figure 2.23: Device Detail Page..........................................................................................47

Figure 2.24: Diagnostics Page ............................................................................................49

-5-

Figure 2.25: Dynamic DNS Conguration Page...............................................................51

Figure 2.26: Contacts Page .................................................................................................52

Figure 3.1: 852 Bridging Router Architecture...................................................................53

Figure 3.2: Bridging Router Mode Setup Page..................................................................54

Figure 3.3: Bridging Router Mode Setup Page..................................................................56

Figure 3.4: Side A Channel List Page in Manual Mode ....................................................57

Figure 3.5: Channel List Page in Manual Mode ................................................................58

Figure 3.6: Two redundant routers between the same channels ......................................59

Figure 3.7: Redundant Twin Mode Application................................................................60

Figure 3.8: Twin Mode Setup Page.....................................................................................64

Figure 3.9: Twin Mode Status Page ....................................................................................67

Figure 4.1: Conguration Server Screen ...........................................................................70

Figure 4.2: Initial LonMaker Drawing...............................................................................72

Figure 4.3: Router Channel Setup......................................................................................72

Figure 4.4: Service Pin Dialog ............................................................................................73

Figure 4.5: Fully Commissioned Router............................................................................73

Figure 4.6: NAT LAN to WAN Architecture .....................................................................74

Figure 4.7: LonMaker New Device Dialog ........................................................................76

Figure 4.8: LonMaker New Device Channel Dialog .........................................................77

Figure 4.9: LonMaker Drawing With Commissioned Monitoring Device .....................77

Figure 4.10: New Virtual Functional Device Dialog.........................................................78

Figure 4.11: Functional Blocks NV Shapes Dialog ...........................................................78

Figure 4.12: Functional Block On Drawing ......................................................................79

Figure 5.1: Optional internal terminator: A. Bus Topology, B. Disabled, C. Free Topology.

-6-

1. Overview

1.1. Introduction

eGRouter (GR4) router supports two open standard protocols, namely ANSI/EIA 709.1 and

ANSI/EIA 852. Both the ANSI/EIA 709.1 and ANSI/EIA 852 are dened by the Consumer

Electronics Association Technology & Standards R7.1 HCS1 Subcommittee. For more details see

http://ce.org/.For the sake of brevity the remainder of the document will refer to the

standards as 709.1 and 852. 709.1 is also known by its trademarked name, LonTalk®. A 709.1

network is also commonly referred to as aLocal Operating Network or LON. is document will

use 709.1 network and LON interchangeably.

e852 protocol acts as the transport service to convey 709.1 messages over Internet Protocol (IP)

networks. is technique of using another protocol (i.e. 852) to transport a message over an

alternate media is oen referred to as tunneling.In 852 parlance the tunneled protocol is a

Component Network (CN) protocol. e852 protocol is a generic tunneling protocol and is not

limited to 709.1. However, a particular implementation of the 852 protocol may only support the

tunneling of a single CN protocol. etunneled CN messages have no information or awareness

of the tunneling process. Although some of the gures in this document use CN or CN/IP to

represent a component network or component network to internet protocol connection, the only

CN currently supported by the GRouter device is 709.1

A component network protocol is oen called a eldbus due to its use for machine to machine

networking and control in the eld.is document, however, will only use the term component

network or CN.

852 not only provides the vehicle to transport ANSI 709.1 messages across IP, but it also provides

management of these connections or routes. A logical grouping of 852 devices that exchange

packets is called an 852 channel. One may think of an 852 channel as a kind of virtual LAN on an

IP network.

A GRouter device forwards 709.1 packets to or from an IP channel (using an Ethernet or WiFi

transceiver) and a CN channel (using twisted pair FT-10 or RS-485 transceivers). eGRouter

device has a presence on, or physical connection to, both channels. erouter takes 709.1

messages from the component network, wraps them in an 852 packet and sends them over the IP

network. eGRouter device also receives 852 packets on its IP interface, unwraps them and puts

the 709.1 messages on the CN channel. evirtual 852 channel looks like a CN channel to CN

nodes. eIP element is transparent. is enables a at network and is more easily managed and

scaled than using CN to IP interfaces that do not hide the IP element from the CN nodes. e

important thing is not what the CN to IP device is called but how transparent it makes the IP

network appear to the CN nodes.

Network connection devices can operate at diﬀerent layers of particular networks protocol stack.

709.1 is an OSI 7 Layer type protocol. Whereas the Internet Protocol has only 4 layers. (See Figure

Figure 2.1 for a diagram of the diﬀerent layers of the two protocols.)

-7-

Fig.1.1: Network Layers

A network connector is a device that joins diﬀerent parts of a network. Connectors have a specic

name that is dependent on the layer at which the connector operates. For example a router

operates at the network layer and a gateway at the application layer. Because higher layers of the

protocol do not have access to some of the information stripped away by lower layers, network

connectors operating at diﬀerent layers have diﬀerent capabilities. ere is also some abuse of

terminology so that the descriptions of network connectors from diﬀerent manufacturers may be

confusing. For example, a repeating router may be called a repeater for short. Although a

repeating router acts similarly to a physical layer repeater, it operates at the network layer and is

not equivalent. It is usually best to nd out at which layer a network connector operates.

Fig.1.2: Network Connector Types and Associated Layers

eGRouter device is amore complex connector because is connects two diﬀerent protocols and

also connects the protocols at diﬀerent layers. On the IP side the GRouter device operates at the

application layer and so is appropriately called an IP Gateway. On the 709.1 side the GRouter

device operates at the network layer and is appropriately called a 709.1 router. So depending on

the user’s perspective the GRouter could be called a gateway or router or a router/gateway. (See

Figure 2.3)

-8-

Fig.1.3: CN to IP Router/Gateway Architecture

e GRouter device also employs a web server for conguration purposes. (See Figure 2.4)

Fig.1.4: GRouter 3 Architecture

1.2. Conguration Parameters

einformation required for successful ANSI/EIA 709.1 transport can be broken up into the

following two categories: device parameters and channel parameters.

Device parameters include information such as: IP address, IP port, Name, and Address of

conguration server.

A channel is a logical grouping of LON to IP routers. eminimum requirement for tunneling

ANSI/EIA 709.1 data is the use of two routers. Router A sends data to Router B and vise versa.

However, routers can also send data to more than one router. In such a case, Router A sends data

to Routers B, C, and D, which in turn send data back.

-9-

A channel, then, is dened as agroup of routers that all send information to each other. elines

of communication are open in both directions and to all members—a complete mesh of

connections.

Typically, channels are managed through the use of a conguration server (called Normal mode

see below). econguration server informs all members in the channel about the channel

information, which includes the adding and removing of channel members. Conguration

servers are capable of managing multiple channels, while routers belong to only one channel at a

time.

Lon to IP routers can also be managed manually by conguring each device uniquely (called

Manual mode, see below). In such a manual conguration, for proper operation, devices must

have mutual membership in each other’s channel lists. at is if Device A is in Device B’s channel

list then Device B must be in Device A’s channel list. However if Device C is in Device B’s channel

list, Device C does not have to be in Device A’s channel list.

1.3. Modes of Operation

e GRouter device can operate in one of two modes: (1) Manual, (2) Normal.

1.3.1. Manual Mode

In Manual mode the user has control over the GRouter device's conguration only. euser can

change the GRouter device's operating information and determine to whom the router will send

information. In Manual mode the GRouter device will honor read requests from other devices or

conguration servers, but it will block requests to write or change internal parameters. is is a

more secure mode and may be preferred on open networks. is mode is also preferable with

non-standard congurations such as Flood Mode or DDNS.

1.3.2. Normal Mode

Normal mode allows the user to view conguration data and channel data set by a remote

conguration server such as an i.LON® conguration server. econguration server sets some

of the operating parameters of the GRouter device. Conguration servers mostly manage the

device's channel. echannel is made up of other devices to which the GRouter device will

tunnel or send ANSI/EIA 709.1 data. In Normal mode the adding and deleting of devices is

managed exclusively by the assigned conguration server. econguration server provides a

single interface to add and delete devices. Finally, Normal mode permits read access to

information by other devices and write access to information for the assigned conguration

server.

Note: Echelon’s LNS based VNI interface (LonMaker) only works in Normal mode. In order for a

GRouter device to communicate directly over an IP channel to a VNI interface requires that the

GRouter device be in Normal mode.

1.4. Applications of the GRouter Device

1.4.1. Multi-site building automation networks

einterfaces described here provide the management necessary for the ANSI/EIA 852 to tunnel

ANSI/EIA 709.1 packets successfully over IP. is ability provides wide area network (WAN)

-10-

Indice

Altri manuali adept technology Router di rete

adept technology

adept technology GRouter3 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza

adept technology GRouter4 Manuale utente

Manuali Router di rete popolari di altre marche