ADJ Startec Series Mini Dekker LZR Manuale utente
User Manual
MINI DEKKER LZR
Rev. 01/2021
©2021 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade-
marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-
tion of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 2
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 3
Unpacking: Thank you for purchasing the Mini Dekker LZR by ADJ Products, LLC. Every Mini Dekker
LZR has been thoroughly tested and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be
damaged, carefully inspect your xture for any damage and be sure all accessories necessary to oper-
ate the unit have arrived intact. In the event that damage is found or parts are missing, please contact
our toll free customer support number for further instructions. Do not return this unit to your dealer
without rst contacting customer support.
Introduction: The Mini Dekker LZR is part of ADJ’s continuing pursuit for creating high quality aord-
able intelligent xtures. The Mini Dekker LZR is a DMX intelligent LED moonower eect with laser.
This xture can be used in a stand alone mode or connected in a Primary/Secondary conguration.
This xture has three operating modes: Sound Active mode, Show mode, and DMX control.
Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up
help and to answer any questions should you encounter problems during your set up or initial opera-
tion. You may also visit us on the web at www.adj.com for any comments or suggestions. Service
Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: (323) 582-2650
Fax: (323) 582-2941
To purchase parts online visit parts.adj.com.
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
Mini Dekker LZR Introduction
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 4
Mini Dekker LZR General Instructions
To optimize the performance of this product, please read these operating instructions carefully to
familiarize yourself with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit for
future reference.
• Includes Hanging Yoke
• 3 Operating Modes: Show Mode, Sound Active, & DMX Control
• Light Weight
• Strobing
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 2 DMX Channel Modes: 2 Channels & 7 Channels
The Mini Dekker LZR carries a 1 Year limited warranty. Please fill out the enclosed warranty card to
validate your purchase. All returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly writ-
ten on the outside of the return package. A brief description of the problem as well as the R.A. num-
ber must also be written down on a piece of paper and included in the shipping container. If the unit
is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain an
R.A. number by contacting customer support at (800) 322-6337.
Mini Dekker LZR Warranty Registration
Mini Dekker LZR Features
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 5
Mini Dekker LZR Safety Precautions
Safety Issue: This unit may “pop” the fuse if the maximum allotted load of 2 amps is reached.
• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is
used to reduce the risk of electrical shock and fire in case of an internal short.
• Do not attempt to operate this unit if the power cord is frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the cover for any reason. There are no user serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• Do not attempt to operate this unit if it has been damaged in any way.
• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power cords should be routed so they are not likely to be walked on or pinched by items placed
upon or against them.
• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the
Cleaning section of this manual for details.
• Heat - The appliance should be situated away from heat sources such as radiators, heat regis-
ters, stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen onto, or liquid has been spilled into, the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a marked change in performance.
Mini Dekker LZR Laser Warnings and Safety
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 6
NON-INTERLOCKED HOUSING WARNING
The Mini Dekker LZR contains internal high-powered laser devices. Do not open the laser housing,
as doing so may result in potential exposure to unsafe levels of laser radiation. If the unit is operated
while open, the laser device can cause instant blindness, skin burns, and res.
CAREFULLY READ ALL LASER SAFETY DATA, OPERATION
INSTRUCTIONS, AND LASER SAFETY BEFORE OPERATING
THIS DEVICE!
The light source emitted from this product can potentially cause eye injury if not set up and used
properly. The light source emitted from a laser is very dierent from any other light sources that may
be encountered in entertainment lighting. Laser light is thousands of times more concentrated than
light from any other kind of light source. This concentration of light can cause instant eye injuries,
primarily by burning the retina (the back of your eyeball containing cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your
audience. Even very small amounts of laser beam light are potentially hazardous even at long dis-
tances. Laser eye injuries can be sustained faster than you can blink.
Do not assume that because this laser splits the laser beam into hundreds of beams and that the
laser beam is scanned out in high speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels internally) before it splits into multiple
beams (Class 3R levels). Many of the individual beams are potentially hazardous to the eyes.
Do not assume that because the laser light is moving, it is safe. This is not true. Nor do the laser
beams always move. Since eye injuries can occur instantly, it is critical to prevent even the smallest
possibility of any direct eye exposure. According to laser safety regulations, it is illegal to aim Class
3R lasers in areas where there is high potential for exposure. This is true even if it is aimed below
people’s faces, such as on a dance oor.
Do not operate the laser without rst reading and understanding all safety and technical data
in this manual.
Always set up and install all laser eects so that all laser light is at least 3 meters (9.8 feet) above the
oor on which people can stand.
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 7
Mini Dekker LZR Laser Warnings and Safety
After setting up this device, and before public use, carry out a test to ensure proper function.
Do not use if any defects are detected. Do not use if the device emits only one or two laser
beams rather than dozens/hundreds, as this could indicate damage to the diraction grating
optic, and could allow emission of higher laser levels above Class 3R.
• Do not point lasers at people or animals. Never look into the laser aperture or laser beams.
• Do not point lasers in areas where people can potentially get exposed, such as uncontrolled bal-
conies, etc.
• Do not point lasers at highly reective surfaces, such as windows, mirrors, and shiny metal. Even
laser reections can be hazardous.
• Never point a laser at aircraft. This is a federal oense.
• Never point un-terminated laser beams into the sky.
• Do not expose the output optic (aperture) to cleaning chemicals.
• Do not use laser if the laser appears to be emitting only one or two beams.
• Do not use the laser if the housing is damaged, if the housing is open, or if the optics appear
damaged in any way.
• Never open the laser housing. The high laser power levels inside of the protective housing can
start res, burn skin, or cause instant eye injury.
• Never leave this device running unattended.
• The operation of a class 3R laser show is only allowed if the show is controlled by a skilled and
well-trained operator who is familiar with the data included in this manual.
• The legal requirements for using laser entertainment products vary from country to country. The
user is responsible for the legal requirements at the location/country of use.
• Always use proper lighting safety cables when hanging lights and eects overhead.
Mini Dekker LZRDMX Set Up
Power Supply: The ADJ Mini Dekker LZR contains an automatic voltage switch, which will automati-
cally sense the voltage when it is plugged into the power source. With this switch there is no need to
worry about the correct power voltage, and this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent xtures and controllers. A DMX controller sends DMX data instructions
from the controller to the xture. DMX data is sent as serial data that travels from xture to xture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufacturers to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. When using several DMX xtures, try to use the shortest cable path possible in order
to ensure proper DMX data transmission. The order in which xtures are connected in a DMX line
does not inuence the DMX addressing. For example, a xture assigned a DMX address of 1 may
be placed anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a
xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address
1 to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The Mini Dekker LZR has two DMX
channel modes: a 2 channel mode and 7 channel mode. The DMX address is set electronically us-
ing the controls on the rear panel of the unit. Your unit and your DMX controller require an approved
DMX-512 110 Ohm Data cable for data input and data output. We recommend Accu-Cable DMX ca-
bles. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This
cable may be purchased at almost all professional sound and lighting stores). Your cables should be
made with a male and female XLR connector on either end of the cable. Also remember that DMX
cable must be daisy chained and cannot be split.
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 8
Notice: Be sure to follow gures two and three when making your own cables. Do not use the
ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug
or allow the shield conductor to come in contact with the XLR cable’s outer casing. Grounding the
shield could cause a short circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-
nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which
is connected between pins 2 and 3 of a male XLR connector (DATA+ and DATA-). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.
5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-
mission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When insert-
ing standard 5-pin data cables in to a 3-pin line a cable adaptor must be used. These adaptors are
readily available at most electronics stores. The chart below details a proper cable conversion.
Mini Dekker LZR DMX Set Up
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 9
Mini Dekker LZR Layout
ADJ Products, LLC - www.adj.com - Mini Dekker LZR User Manual Page 10
1. Function Display: Used to show the various menus and selected functions.
2. Buttons:
MENU Select programming functions
UP Go backward in the menu of functions
DOWN Go forward in the menu of functions
ENTER Confirm selection
3. DMX In/Out: Used to link multiple units together via 3-pin XLR cables.
4. Power In: Used to connect to the power supply.
5. Laser Switch: Used to turn the laser on or o. (EU version only)
Indice
Altri manuali ADJ Proiettore
ADJ
ADJ MICRO 3D II Manuale utente
ADJ
ADJ ULTRA HEX BAR 6 Manuale utente
ADJ
ADJ Revo Rave Manuale utente
ADJ
ADJ FLAT PAR QWH12XS Manuale utente
ADJ
ADJ ULTRA HEX BAR 6 Manuale utente
ADJ
ADJ H20 DMX IR Manuale utente
ADJ
ADJ P64 LED Plus Manuale utente
ADJ
ADJ Par ZP100 3K Manuale utente
ADJ
ADJ 4 STAGE PAK Manuale utente
ADJ
ADJ Inno Pocket Spot LZR Manuale utente
ADJ
ADJ Illusion Dotz 4.4 Manuale utente
ADJ
ADJ Vizi Hybrid 16RX Manuale utente
ADJ
ADJ FLAT PAR QA12XS Manuale utente
ADJ
ADJ XS 600 Manuale utente
ADJ
ADJ H2O DMX PRO Manuale utente
ADJ
ADJ HYDRO SPOT 1 Manuale utente
ADJ
ADJ FOG FURY 1000 Manuale utente
ADJ
ADJ Crazy Pocket 8 Manuale utente
ADJ
ADJ galaxian move Manuale utente
ADJ
ADJ MEGA TRIPAR PROFILE PLUS Manuale utente
