ADT Door and Window Detector Manuale utente
ADT Door and
Window Detector
Setup Guide
PRINTER’S INSTRUCTIONS:
MANUAL,QUICK START,NOVA,DW - NORTEK P/N: 10015708C - INK: BLACK PLUS PMS 286C - MATERIAL: 105G COATED PAPER - SIZE: 105MM X 105MM -
SCALE: 1-1 - BINDING: TRIM, FOLD AND SADDLE STITCHED - PAGE 1 OF 16
Take the ADT Door and Window Detector to where
you intend to mount it after setup.
1. 2.
Setup
A
• Make sure you are within 350 feet from the
ADT Security Hub. (Exact range depends on
your home’s construction, the environment, the
position of the ADT Security Hub, and the position
and number of other connected devices.)
• Make sure that your ADT Security Hub is disarmed
before connecting a new device.
• Make sure that you only setup one new device
at a time.
3.
• Do not remove the battery tab until you are ready
to set up the detector.
Take the ADT Door and Window Detector to where
you intend to mount it after setup.
2. Use the SmartThings app on your smartphone
to select the “My Home” tab. Select "Things", and
then “Add a Thing".
Setup
Setup
• Make sure you are within 350 feet from the
ADT Security Hub. (Exact range depends on
your home’s construction, the environment, the
position of the ADT Security Hub, and the position
and number of other connected devices.)
• Make sure that your ADT Security Hub is disarmed
before connecting a new device.
• Make sure that you only setup one new device
at a time.
Use the SmartThings app to scan the QR code on the
back of the detector and then follow the on-screen
instructions to complete setup.
3.
Detector (Back)
QR Code
• Do not remove the battery tab until you are ready
to set up the detector.
5.
Setup
Remove the QR code from the back of the detector
and attach it inside the ADT Security Hub User Guide
for future reference.
4. Remove the tab on the detector marked “Pull This
Tab”.
Battery Tab
B
Make sure that the alignment marks on both parts of the
detector are aligned and facing each other.
Remove the QR code from the back of the detector
and attach it inside the ADT Security Hub User Guide
for future reference.
Remove the tab on the detector marked “Pull This
Tab”.
Placement
B
Make sure that the alignment marks on both parts of the
detector are aligned and facing each other.
Detector
Magnet
Alignment Marks
Placement on doors:
Door Frame
Detector On Door Frame
Magnet Mounted On Door
Placement
Placement
Detector On Door Frame
Placement on windows:
Single-Hung Windows Double-Hung Windows
Detector On Window Sill
Mounting
C
1. Use the pre-applied adhesive tape when attaching
both parts of the detector to your door or window.
• Make sure that all surfaces are clean and dry.
• Make sure to place both parts of the detector
correctly as the adhesive tape will be difcult
to remove.
• Place the detector at the top of door or window
frames to avoid accidental damage.
2.
Mounting
Use the pre-applied adhesive tape when attaching
both parts of the detector to your door or window.
• Make sure that all surfaces are clean and dry.
• Make sure to place both parts of the detector
correctly as the adhesive tape will be difcult
to remove.
• Place the detector at the top of door or window
frames to avoid accidental damage.
Mounting
2. Place one part of the detector on your door or
window, and the other part on the frame of the
door or window.
• Make sure that both parts of the detector are less
than 0.5 inches apart when the door or window
is closed. Use optional spacer if required.
• For double doors, attach the smaller part of the
detector to the most-used door and the larger
part to the least-used door.
1. Insert spacer pin into magnet base slot.
Mounting
Magnet
Spacer
2. Slide spacer forward to lock it onto the magnet.
Magnet
Spacer
You can test your ADT Door and Window Detector by
performing a Walk Test on the ADT Security Hub, opening
and closing the door or window where it's been installed,
and then checking its status on the ADT Security Hub
touchscreen. See the ADT Security Hub User Guide for
more details.
D
Note: If you have an ADT professional monitoring service
activated, additional testing is required whenever you
connect a new device. Follow the on-screen instructions
in the SmartThings app to complete testing.
If it's difcult to align both parts of the detector
properly, you may want to adjust the height of the
magnet by squeezing the tabs on the side or by adding
the supplied spacer:
Indice
Altri manuali ADT Sensore di sicurezza
ADT
ADT SiXCTA Manuale utente
ADT
ADT Visonic PowerMax Plus Manuale utente
ADT
ADT BHS-4000A Manuale utente
ADT
ADT Ademco 5898 Manuale utente
ADT
ADT TSSC Guida utente
ADT
ADT Home Assist Manuale utente
ADT
ADT Home Assure Manuale utente
ADT
ADT Safewatch Plus Manuale utente
ADT
ADT TMD15 Manuale utente
ADT
ADT DSC 9155 Alexor Manuale utente
