ADTRAN NetVanta Series Manuale utente

Technical Support +1-256-963-8716

NetVanta Series

(with E1/FE1 or E1/FE1 + G.703 Drop Network Interface Module)

Quick Configuration Guide 64200868L1-42C March 2005

• Category 5 - UTP cable for connecting the system to the existing network.

• VT100 terminal or PC with VT100 emulation software.

• DB-9 (male) to DB-9 (female) straight-through cable for configuring the unit.

Frame Relay Diagram

PPP over Fractional E1 Connection Diagram

Equipment Required

This quick configuration guide provides step-by-step instructions for configuring

your application. The configuration scripts are available on the ADTRAN OS

Documentation CD.

The configuration parameters used in the example outlined in this document are for

instructional purposes only. Please replace all underlined entries (example) with your

specific parameters to configure your application.

Network Diagrams

Branch Office Corporate HQ

NetVanta

LAN IP: 10.10.10.1 /24

WAN IP: 192.168.72.2 /30

eth 0/1

LAN IP: 10.10.20.7 /24

PWR STAT TD

VPN

RD TD RD TD RD

WAN LAN

PWR STAT TD

VPN

RD TD RD

NetVanta3200

WAN LAN

DLCI 16

Annex D Signaling

192.168.72.1 /30

FR 1.x

e1 1/2

e1 1/1

PBX

Timeslots 1-15 Data,

Timeslots 17-31 Voice*

* Voice circuits require timeslot 16 for signaling. If voice is

required on the e1 1/2 G.703 port, the largest data map

which can be configured is timeslots 1 - 15 (leaving 17 - 31

for voice) or 17 - 31 (leaving 1 - 15 for voice).

Network IP: 10.10.20.0

Network IP: 190.72.22.0

Branch Office Corporate HQ

NetVanta

LAN IP: 10.10.10.1 /24

eth 0/1

LAN IP: 10.10.20.7 /24

WAN IP: 192.168.72.2 /30

PWR STAT TD

VPN

RD TD RD TD RD

WAN LAN

PWR STAT TD

VPN

RD TD RD

NetVanta3200

WAN LAN

Point-to-Point E1

Timeslots 1-15 Data,

Timeslots 17-31 Voice*

PPP Signaling

192.168.72.1 /30

PPP 1

e1 1/2

e1 1/1

PBX

* Voice circuits require timeslot 16 for signaling. If voice is

required on the e1 1/2 G.703 port, the largest data map which

can be configured is timeslots 1-15 (leaving 17-31 for voice) or

17-31 (leaving 1-15 for voice).

Network IP: 10.10.20.0

Network IP: 190.72.22.0

2 Technical Support +1-256-963-8716 64200868L1-42C

The NetVanta may be initially accessed and managed either via a console session or through a

Telnet session. Refer to Initiate a Console Session for console session instructions. Initiating a

Telnet session requires using a hub and two Ethernet cables (one for the PC and one for the

unit). The default Ethernet IP address is 10.10.10.1. Refer to Configure Telnet Access on page 7

to change Telnet session settings.

1. Connect a VT100 terminal (or PC with VT100 emulation software) to the NetVanta

CONSOLE port using a DB-9 (male) to DB-9 (female) straight-through serial cable.

2. Configure the COM port with the following parameters:

Data Rate: 9600

Data Bits: 8

Parity Bits: None

Stop Bits: 1

Flow Control: None

3. Open a VT100 terminal session. (Please refer to the appropriate VT100 terminal software

documentation for detailed instructions.)

4. Press the <Enter> key.

5. Enter enable at the >prompt.

6. Enter the password when prompted. The default password is password.

7. You are now at the #prompt. At the #prompt, enter config terminal to enter the Global

Configuration mode.

1. At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for

the Ethernet port located on the rear panel of the unit.

2. Enter ip address 10.10.20.7 255.255.255.0 to assign an IP address to the Ethernet port

using a 24-bit subnet mask.

3. Enter no shutdown to activate the interface to pass data.

4. Enter exit to exit the Ethernet interface commands and return to the Global Configuration

mode.

Configure the Unit

Initiate a Console Session

Configure the Ethernet Port Parameters

If you are accessing the NetVanta via Telnet, once you change this IP address, you will

lose connection to the NetVanta. You must change the IP address of your PC before you

can proceed.

ADTRAN recommends that you set the Ethernet speed and duplex to match the switch or

hub it is plugged in to.

For example: (config-eth 0/1)#speed 10

(config-eth 0/1)#half-duplex

64200868L1-42C Technical Support +1-256-963-8716 3

1. At the (config)# prompt, enter interface e1 1/1 to activate the interface configuration mode

for the E1 network interface.

2. If necessary (this is the default), enter clock source line to configure the unit to recover

clocking from the E1 network connection.

3. If two units are configured on a private E1 (PPP mode), set one unit to clock source line and

the other to clock source internal. For Frame Relay, set both ends to clock source line.

The following steps demonstrate configuring an E1 network interface with timeslots 1 through 15

for data.

1. At the (config-e1 1/1)# prompt, enter framing crc4.

2. Enter sa4tx-bit 0.

3. Enter tdm-group 1 timeslots 1-15 speed 64 to create a TDM group for timeslots 1 through

15 (the data timeslots) on the E1 network connection (e1 1/1).

4. Enter no shutdown to activate the interface.

5. Enter interface e1 1/2 to activate the interface configuration mode for the G.703 network

interface.

6. Enter no shutdown to activate the interface.

7. Enter exit to return to the Global Configuration mode.

The NetVanta Network Interface Modules (NIMs) use a slot/port notation for interface

identification. All non-modular interfaces built into the base unit (e.g., the Ethernet port) are

identified using 0as the slot number.

Begin the E1 Network Interface Configuration

You should only need to change this setting for PPP, which will have one end set to line

(default) and the other end set to internal.

Create the E1 Interface TDM Group

The NetVanta automatically maps timeslots 1 through 31 from the network connection of

the E1/FE1 + G.703 NIM to the G.703 port. Creating a TDM group removes the specified

timeslots from the G.703 map. All remaining timeslots not included in the TDM group will

be passed from the network port (e1 1/1) to the G.703 port (e1 1/2).

Voice circuits require timeslot 16 for signaling. If voice is required on the e1 1/2 G.703

port, the largest data map which can be configured is timeslots 1 through 15 (leaving 17

through 31 for voice) or 17 through 31 (leaving 1 through 15 for voice).

Timeslot 0 is for synchronization, alarm transport, and international carrier use. It is not

accessible for use for voice or data.

4 Technical Support +1-256-963-8716 64200868L1-42C

1. Enter interface e1 1/2 to activate the interface configuration mode for the DSX-1 interface.

2. Enter multiframe ts16 to verify the G.703 interface is configured for voice signaling (timeslot

16 used for signaling).

3. Enter no shutdown to activate the G.703 interface.

4. Enter exit to return to the Global Configuration mode.

The following steps outline configuring a Frame Relay virtual interface (labeled 1) using a single

DLCI back to the corporate router (defined as DLCI 16).

1. At the (config)# prompt, enter interface fr 1 to create a Frame Relay virtual interface

labeled 1.

2. If the default setting of ansi was changed, enter frame-relay lmi-type ansi to configure

Frame Relay virtual interface 1 to use ANSI (Annex D) signaling.

3. Enter no shutdown to activate the virtual interface to pass data.

4. Enter exit to return to the Global Configuration mode.

5. The unit has a factory default PPP 1 interface. Enter the command no ppp 1 to remove this

interface.

1. At the (config)# prompt, enter interface fr 1.16 to create a PVC assigned to Frame Relay

virtual interface 1. This activates the configuration parameters for the PVC. Your prompt

should now display (config-fr 1.16)#.

2. Enter frame-relay interface-dlci 16 to assign DLCI 16 to this PVC.

3. Enter ip address 192.168.72.1 255.255.255.252 to assign an IP address of 192.168.72.1 for

this PVC using a 30-bit subnet mask.

4. Enter no shutdown to activate the virtual interface to pass data.

5. Enter exit to return to the Global Configuration mode.

6. If you are configuring the NetVanta for use in a Frame Relay application and have completed

this step, skip to Create the Cross-Connect on page 5.

Skip to Configure the Virtual PPP Interface on page 5 for PPP configuration.

Configure the G.703 Interface (Optional)

Configure the Frame Relay Virtual Interface

Create the PVC and Assign an IP Address

The default encapsulation is RFC 1490 or IETF. Make certain the remote unit uses the

same encapsulation for Frame Relay.

64200868L1-42C Technical Support +1-256-963-8716 5

The following steps show how to configure a PPP virtual interface (labeled 1) to the corporate

router. Skip to Create the Cross-Connect below if you are using Frame Relay.

1. At the (config)# prompt, enter interface ppp 1 to create a PPP virtual interface labeled 1.

2. Enter ip address 192.168.72.1 255.255.255.252 to assign an IP address to the PPP

endpoint using a 30-bit mask.

3. Enter no shutdown to activate the virtual interface to pass data.

4. Enter exit to return to the Global Configuration mode.

1. For Frame Relay applications, at the (config)# prompt, enter cross-connect 1 e1 1/1 1

frame-relay 1 to connect the E1 network connection (e1 1/1) to the virtual Frame Relay

interface (fr 1.16).

2. For PPP applications, enter cross-connect 1 e1 1/1 1 ppp 1 to connect the E1 network

connection (e1 1/1) to the virtual PPP interface (ppp 1).

Routes may be assigned either statically or dynamically. Continue with this section to create a

static route. Refer to the next section for information on configuring RIP and OSPF dynamic route

assignments.

Depending on your network setup, configure static routing on your unit in one of the following

ways.

Scenario 1: Configuration for Corporate HQ router in the diagram on page 1 (Static Route

to the Far Side/Internet Access at Local Site)

1. At the (config)# prompt, enter ip route 10.10.20.0 255.255.255.0 ppp 1 (or frame-relay

1.16) to set up the static route.

2. Enter ip route 0.0.0.0 0.0.0.0 10.10.10.x (i.e., address of internet router) to set up the default

route.

Scenario 2: Configuration for Branch Office router in the diagram on page 1 (No Internet

Access at Local Site)

1. At the (config)# prompt, enter ip route 0.0.0.0 0.0.0.0 ppp 1 (or frame-relay 1.16) to set up

the default route.

Configure the Virtual PPP Interface

Create the Cross-Connect

Configure Static Routes

These examples are based on the network diagrams on page 1.

6 Technical Support +1-256-963-8716 64200868L1-42C

2. The internet router at the far side will need a route statement to send traffic back to this

network through the NetVanta router. The information (based on the diagram shown at the

beginning of this document) is as follows:

• Destination address: 10.10.20.0 (remote LAN)

• Subnet mask: 255.255.255.0

• Gateway: 10.10.10.1 (NetVanta Router’s Ethernet)

Scenario 1: Dynamic Routing via OSPF

1. At the (config)# prompt, enter router ospf to activate the OSPF configuration mode. Your

prompt should now display (config-ospf)#.

2. Specify the networks:

Corporate HQ Router

(config-ospf)#network 10.10.10.0 0.0.0.255 area 0

(config-ospf)#network 192.168.72.0 0.0.0.3 area 0

Branch Office Router

(config-ospf)#network 10.10.20.0 0.0.0.255 area 0

(config-ospf)#network 192.168.72.0 0.0.0.3 area 0

3. Enter exit to return to the Global Configuration mode.

Scenario 2: Dynamic Routing via RIP

1. At the (config)# prompt, enter router rip to activate the RIP configuration mode. Your prompt

should now display (config-rip)#.

2. Enter version 2 to globally define RIP version 2 on all interfaces.

3. Specify the networks:

Corporate HQ Router

(config-rip)#network 10.10.10.0 255.255.255.0

(config-rip)#network 192.168.72.0 255.255.255.252

Branch Office Router

(config-rip)#network 10.10.20.0 255.255.255.0

(config-rip)#network 192.168.72.0 255.255.255.252

4. Enter exit to return to the Global Configuration mode.

1. Verify that the prompt of your unit displays (config)#.

2. Enter enable password word to set the Enable Security mode password.

3. Enter enable password md5 word to encrypt the enable password using MD5 encryption.

Configure Dynamic Routes

Set the Enable Security Mode Password

The Enable Security mode passwords are case sensitive.

64200868L1-42C Technical Support +1-256-963-8716 7

The following steps show how to access the Telnet configuration parameters and change the

password. The default password for initializing a Telnet session is password (all lowercase). For

security purposes, change the password to something unique. For this example, replace the

underlined word with a password of your choosing. The NetVanta supports five Telnet sessions

(0 through 4).

1. Verify that the prompt of your unit displays (config)#.

2. Enter line telnet 0 4 to change the configuration parameters for the Telnet session.

3. Enter login to initiate Telnet access.

4. Enter password word to change the login password for the Telnet session.

5. Enter exit to return to the Global Configuration mode.

1. Verify that the prompt of your unit displays (config)#.

2. Enter exit to leave configuration mode.

3. Enter copy running-config startup-config to save the current configuration to memory. This

command may be abbreviated as copy run start.

4. Enter exit to close the configuration session.

The NetVanta is now configured and operational. Complete the installation by connecting the

appropriate cables to the E1 and Ethernet networks. Please refer to your NetVanta Hardware

Installation Guide for more details on pinouts and cabling.

Configure Telnet Access

An enable security mode password and the Ethernet port parameters must be defined

before configured Telnet sessions are activated. Refer to Configure the Ethernet Port

Parameters on page 2 and Set the Enable Security Mode Password on page 6 for

information.

Save the Configuration

Complete the Installation

Indice

Altri manuali ADTRAN Hardware di rete

ADTRAN

ADTRAN Total Access 900 Series Manuale utente

ADTRAN

ADTRAN 6540 Manuale del prodotto

ADTRAN

ADTRAN IQ Probe 1200214L1 Manuale utente

ADTRAN

ADTRAN DSU III AR Manuale utente

ADTRAN

ADTRAN ESU LT Manuale utente

ADTRAN

ADTRAN NetVanta 834 Manuale del proprietario

ADTRAN

ADTRAN 411 Manuale utente

ADTRAN

ADTRAN XFP Manuale utente

ADTRAN

ADTRAN SHDSL NxNTU Manuale di istruzioni

ADTRAN

ADTRAN eSBC Manuale utente

ADTRAN

ADTRAN ATM Mini-DSLAM Manuale utente

ADTRAN

ADTRAN E1 Manuale utente

ADTRAN

ADTRAN Cable T1 ESF CSU ACE Manuale utente

ADTRAN

ADTRAN Total Access 900 Series Manuale utente

ADTRAN

ADTRAN P/N 1204011L1 Manuale di servizio

ADTRAN

ADTRAN DSU IV ESP Manuale utente

ADTRAN

ADTRAN Dial Backup Interface Module 1204006L2 Manuale utente

ADTRAN

ADTRAN BR10 Manuale utente

ADTRAN

ADTRAN 200410L1 Manuale utente

ADTRAN

ADTRAN Express 6500 Series Manuale di istruzioni

ADTRAN

ADTRAN 4202023L1 Manuale utente

ADTRAN

ADTRAN Total Access 832 Manuale utente

ADTRAN

ADTRAN NT1 ACE Manuale utente

ADTRAN

ADTRAN NetVanta 1224 Manuale di istruzioni

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente