Advantech MIC-1810 Manuale di installazione e funzionamento
MIC-1810 Startup Manual 1
Before you begin installing your card, please make sure
that the following items have been shipped:
1. 1 x MIC-1810 system
2. 1 x Adapter 100 ~ 240 V 60W 12 V WO/PFC
DC plug 90°
3. 1 x MIC-1810 startup manual
4. 1 x User note for MIC-1810
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Caution:
BATTERIES ARE AT RISK OF EXPLODING IF
INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE RECOMMEND-
ED BY THE MANUFACTURER. DISCARD USED
BATTERIES ACCORDING TO THE MANUFAC-
TURER’S INSTRUCTIONS.
Attention:
DANGER D’EXPLOSION SI LA BATTERIE EST
INEXACTEMENT REMPLACÉE. REMPLACEZ
SEULEMENT AVEC LA MÊME CHOSE OU LE TYPE
ÉQUIVALENT RECOMMANDÉ PAR LE FABRICANT,
JETTENT LES BATTERIES UTILISÉES INSTRUC-
TIONS DE S SELON FABRICANT DES’.
MIC-1810
Intel
®
Core™ i3-3217UE/Celeron
®
1047UE
Embedded Automation Computer
Startup Manual
System
• 3rd generation Intel®Core™ i processer with QM77 chipset
Memory
• 4G SODIMM DDR3-1600 204 pin 512MX8 1.35 V
Graphics
• Intel
®
HD Graphics 4000, supports DirectX11
Serial Ports
• 2 x RS-232 via COM1/COM2
Ethernet
• Interface: 10/100/1000 Mbps
• Controller
LAN1: QM77 (MAC) + 82579LM GbE (PHY)
LAN2: 82583V Gigabit Ethernet controller
Storage
• Internal SSD Bay: 1 x 2.5” SSD bay
Front I/O
• Display: 1 x VGA/HDMI
• USB: 2 x USB 3.0, 2 x USB 2.0
Power Requirement
• Power Type: DC power jack
• Input Voltage: 12 VDC
Miscellaneous
• Power Switch
Orange: System standby
Green: System boot
Table Mount (Optional)
• P/N: 1960077844N001
• Dimensions (W x L): 130 x 175 mm
Environment
• Operating Temperature:
0 ~ 50 °C with 0.7m/S air flow
and 1 x industrial SSD
• Relative Humidity: 95% @ 40 °C (non-condensing)
Physical Characteristics
• Dimensions (W x H x D): 165 x 130 x 59 mm
• Weight: 1.45 kg (3.19 lb)
Specications Packing List
For more information about this or other Advantech
products, please visit our website at
http://www.advantech.com
http://www.advantech.com/Products
For technical support and service, please visit our
support website at
http://support.advantech.com.tw/support/default.
aspx
This manual is for the MIC-1810 Series Rev. A1.
Part No. 2001181001
Printed in Taiwan
Edition 2
September 2017
2 MIC-1810 Startup Manual
Analog Output
Channels 2
Resolution 12 bits
Memory Size 4K samples
Update Rate 500 KS/s
Output
Range
Internal
Reference 0~ 5 V, 0 ~ 10 V, ±5 V, ±10 V
External
Reference
Unipolar
Bipolar
Reference Input
-10 ≤ x ≤ 10 V
Maximum Range
0 ~ x V
-x ~ x V
Accuracy
Relative ±1 LSB
Differential
Non-Linearity ±1 LSB (monotonic)
Slew Rate 20 V/us
Gain Error Adjustable to zero
Drift 30 ppm/Ω
Driving
Capability 5 mA
Update
Mode Static update, waveform
Output
Impedance Max. 0.1 Ω
Digital I/O
Channels 24 (shared), TTL compatible
Input Voltage
Low 0.8 V max.
High 2 V min.
Output Voltage
Low 0.8 V max.@ +15mA(sink)
High 2 V min.@ -15mA(source)
Input Load 10KΩ pull-up resistor connect to 5 V
The MIC-1810 system features a built-in data acquisition
module (MIOe-3810).
Analog Input
Channels 16 single ended/8 differential
Resolution 12 bits
Built-In
Memory 4K samples
Sampling
Rate
Single channel 500 KS/s
Multi channels 800 KS/s
Input
Range and
Gain List
Gain 0.5 1 2 4 8
Unipolar NA 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25
Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625
Drift
Gain 0.5 1 2 4 8
Zero 25 ppm/°C
Span 15 ppm/°C
Input Signal
Bandwidth
(-3dB)
Gain 0.5 1 2 4 8
BW (MHz) 1 1.6 1.2 1.2 1.2
Max. Input
Voltage ± 15 V
Input Im-
pedance 1G Ω / 2pF
Sampling
Mode Software or external
Trigger
Mode
Start trigger, Delay trigger start,
Stop trigger, Delay trigger stop
Accu-
racy
DC
INLE: ± 1 LSB (with manual calibration)
DNLE: ± 1 LSB (with manual calibration)
Offset error: Adjustable to zero
Gain 0.5 1 2 4 8
Gain Error
(%FSR) 0.1 0.1 0.2 0.2 0.4
Channel
Type Single ended/differential
AC
SNR: 68 dB
ENOB: 10.5 bits
External
Digital
Trigger
Low: 0.8 V max.; High: 2.0 V min.
Minimum pulse width: 50 ns
External Ana-
log Trigger
Range: -10 ~ 10 V
Resolution: 12 bits (4.88 mV/step)
DAQ Specications
DAQ Specications (Cont.)
MIC-1810 Startup Manual 3
Counter
Counter chip N/A
Channels 2 channels (independent)
Resolution 32 bits
Compatibility TTL level
Base Clock Internal 20 MHz or external clock (10 MHz max.),
selectable via software
Input Frequency Max. 10 MHz
Clock Input
Low 0.8 V max.
High 2.0 V min.
Gate Input
Low 0.8 V max.
High 2.0 V min.
Counter Output
Low 0.8 V max. @+15mA
High 2.0 V min. @-15mA
Error in
Advanced
Functions
Frequency
Measurement
0.1% when the input signal
frequency is ≥ 40 KHz
Pulse Width
Measurement
0.1% when the input signal
frequency is ≤ 40 KHz
Pulse Output Within 2% when the output
frequency is > 1 MHz
PWM Output Within 2% when the output
frequency is > 1 MHz
HDD Installation
1. Unscrew the 4 screws and remove the rear cover.
2. Unscrew the 4 screws affixing the SSD to the rear
cover.
3. Replace the SDD with an HDD.
4. Affix the HDD to the rear cover using the 4 screws.
5. Reconnect the SATA and power cables and replace
the rear cover. Secure in place using the 4 screws.
Table Mount Installation
MIC-1810 can be integrated with a table mount for easy
operation. To prevent the system from overheating, the side
of the system with the heat sink must be facing upward.
1. Unscrew the 4 screws affixing the rear cover in place.
2. Align the screw holes of the rear cover with the screw
holes of the table mount. Secure the system to the rear
cover and table mount using the 4 screws.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. The device must not cause harmful interference.
2. The device must accept any interference received,
including interference that may cause undesired
operation
Installation Procedures (Cont.)
DAQ Specications (Cont.)
Declaration of Conformity
Installation Procedures
4 MIC-1810 Startup Manual
System I/O Interface
System Dimensions
MIC-1810快速入门手册
1
安装板卡之前，用户需确认包装中含有本设备以及下面所
列各项：
1. 1 x MIC-1810系统 x 1
2. 1 x 适配器100 ~ 240 V 60W 12 V WO/PFC
DC plug 90°
3. 1 x MIC-1810快速入门手册
4. 1 x MIC-1810用户指南
如果其中任何一项缺失或损坏，请立即与经销商或销售代
表联系。
注意:
如果电池更换不正确，将有爆炸的危险。因此，只
可以使用制造商推荐的同一种或者同等型号的电池
进行替换。请按照制造商的指示处理旧电池。
Attention:
DANGER D’EXPLOSION SI LA BATTERIE EST INEX-
ACTEMENT REMPLACÉE. REMPLACEZ SEULEMENT AVEC
LA MÊME CHOSE OU LE TYPE ÉQUIVALENT RECOM-
MANDÉ PAR LE FABRICANT, JETTENT LES BATTERIES
UTILISÉES INSTRUCTIONS DE S SELON FABRICANT
DES’.
MIC-1810
Intel® Core™ i3-3217UE/ Celeron 1047UE微型计算机
快速入门手册
处理器系统
• Intel第三代Core i处理器，带QM77芯片组
内存
• 4G SODIMM DDR3-1600 204针512MX8 1.35 V
显示
• Intel® HD Graphics 4000，支持DirectX11
串行端口
• 2 x RS-232 from COM1/COM2
以太网
• 端口：10/100/1000 Mbps
• 控制器
LAN1：QM77 (MAC) + 82579LM GbE (PHY)
LAN2：82583V Gigabit Ethernet controller
存储
• 内置2.5”SSD磁盘盒：1
前部I/O
• 显示：1 x VGA/HDMI
• USB：2 x USB 3.0，2 x USB 2.0
电源需求
• 电源类型：DC电源插孔
• 电源输入电压：12 VDC
其它
• 电源开关
（橙色：系统待机/绿色：系统电源启动）
桌面安装（可选）
• P/N：1960077844N001
• 尺寸（W x L）：130 x 175 mm
环境
• 工作温度:
0 ~ 50 °C，0.7m/S气流：带1 x工业SSD
• 相对湿度：95% @ 40 °C（非凝结）
物理特性
• 尺寸 (W x H x D)：165 x 130 x 59 mm
• 重量：1.45 kg (3.19 lb)
产品规格 包装清单
如需了解有关本产品及研华其它产品的详细信息，请访
问我们的网站：
http://www.advantech.com
http://www.advantech.com/Products
如需技术服务与支持，请访问我们的技术支持网站：
http://support.advantech.com.tw/support/default.
aspx
本手册适用于MIC-1810系列Rev. A1。
Part No.2001181001
台湾印刷
第二版
2017年9月
2
MIC-1810快速入门手册
模拟量输出
通道 2
分辨率 12 bits
内存容量 4K采样数
更新速率 500 KS/s
输出范围
内部电压位准 0 ~ 5 V, 0 ~ 10 V, ±5 V, ±10 V
外部电压位准
单极
双极
参考输入
-10 ≤ x ≤ 10 V
最大范围
0 ~x V
-x ~ x V
精度
相对 ±1 LSB
差分非线性 ±1 LSB（单调）
转换速率 20 V/us
增益误差 可调至0
偏移 30 ppm/Ω
电流推动能力 5 mA
输出模式 静态输出、周期波形输出
输出阻抗 最大0.1Ω
数字量输入/输出
通道 24路（共享），TTL兼容
输入电压
低 最大0.8 V
高 最小2 V
输出电压
低 0.8 V max.@ +15mA（灌电流）
高 2 V min.@ -15mA（拉电流）
输入负载 10KΩ上拉电阻，连接至 5V
DAQ系统内置数据采集模块MIOE-3810。
模拟量输入
通道 16路单端/8路差分
分辨率 12 bits
内置内存 4K采样数
采样速率
单路 500 KS/s
多路 800 KS/s
输入范围和
增益列表
增益 0.5 1 2 4 8
单极 NA 0 ~ 10 0 ~ 50 ~ 2.5 0 ~ 1.25
双极 ±10 ±5 ±2.5 ±1.25 ±0.625
偏移
增益 0.5 1 2 4 8
零 25 ppm/°C
量程 15 ppm/°C
输入信号带
宽 (-3dB)
增益 0.5 1 2 4 8
BW
(MHz) 1 1.6 1.2 1.2 1.2
最大输入
电压 ±15 V
输入阻抗 1GΩ/2pF
采样模式 软件或外部
触发模式 启动触发, 延迟启动触发，
停止触发，延迟停止触发
精度
DC
INLE：±1 LSB（需手动校准）
DNLE：±1 LSB（需手动校准）
偏移误差：可调至0
增益 0.5 1 2 4 8
增益误
差
(%FSR)
0.1 0.1 0.2 0.2 0.4
通道类
型单端/差分
AC
SNR：68 dB
ENOB：10.5 bits
外部数字量
触发
低：最大0.8V；
高：最小2.0V
最小脉冲宽度：50 ns
外部模拟量
触发
范围：-10 ~10V
分辨率：12 bits (4.88 mV/step)
DAQ规格
DAQ规格（续）
MIC-1810快速入门手册
3
计数器
计数器芯片 N/A
通道 2 通道（独立）
分辨率 32 bits
兼容性 TTL电平
基准时钟 内部20MHz或外部时钟（最大10 MHz）.
可通过软件选择
输入频率 最大10MHz
时钟输入
低 最大0.8 V
高 最小2.0 V
门输入
低 最大0.8 V
高 最小2.0 V
计数器输出
低 最大0.8 V @+15mA
高 最小2.0 V @-15mA
高级功能误差
频率测量 0.1%，输入信号频率 ≥ 40KHz
脉冲宽度测量 0.1%，输入信号频率 ≤ 40KHz
脉冲输出 小于2%，输出频率 > 1MHz
PWM输出 小于2%，输出频率> 1MHz
HDD安装
1. 卸下4颗螺丝后移除底盖。
2. 从底盖上卸下用于固定SSD的4颗螺丝。
3. 插接SATA线缆/电源线后放回后盖并用4颗螺丝固定。
桌面安装
MIC-1810支持桌面安装。为避免系统过热，散热片一侧必须
朝上放置。
1. 卸下4颗螺丝。
2. 底盖对齐后使用4颗螺丝进行固定完成桌面安装。
本品符合FCC规则第15款限制。操作符合下列两种情况：
1. 此设备不可产生干扰，
2. 本设备必须接受任何收到的干扰，但干扰可能导致意外
操作。
简易安装指导（续）
DAQ规格（续）
符合性声明
简易安装指导
4
MIC-1810快速入门手册
系统I/O接口
系统尺寸
Altri manuali per MIC-1810
3
Indice
Altri manuali Advantech Scrivania
Advantech
Advantech POC-W181 Manuale di istruzioni
Advantech
Advantech DS-410 Manuale utente
Advantech
Advantech SKY-642 4U Manuale di installazione e funzionamento
Advantech
Advantech PCA-6013 Manuale di installazione e funzionamento
Advantech
Advantech AIM-37AT Manuale utente
Advantech
Advantech USC-160 Series Manuale di installazione e funzionamento
Advantech
Advantech TPC-1570H Manuale utente
Advantech
Advantech MIT-W102 Series Manuale di installazione e funzionamento
Advantech
Advantech TREK-550 Manuale utente
Advantech
Advantech UTC-520FP-IKA0E Series Manuale di installazione e funzionamento
Advantech
Advantech UNO-1252G Series Manuale utente
Advantech
Advantech UNO-2050G Manuale utente
Advantech
Advantech PCM-5820 Series Manuale utente
Advantech
Advantech ARK-3531 Series Manuale utente
Advantech
Advantech PCM-9388 Manuale utente
Advantech
Advantech EPC-R4710 Manuale utente
Advantech
Advantech MIC-770 Manuale utente
Advantech
Advantech EPC-S201 Manuale utente
Advantech
Advantech UNO-4683 Manuale utente
Advantech
Advantech UNO-3072L Manuale utente
