Advantek Networks AWN-AP-54MR Manuale utente

802.11b+g Access Point

User Manual

Model: AWN-AP-54M

FCC Certifications

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC ules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 eorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this

device could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

FCC F adiation Exposure Statement

This equipment complies with FCC F radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and

operated with a minimum distance of 20cm between the radiator and your

body.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may

cause radio interference, in which case the user may be required to take

adequate measures.

All trademarks and brand names are the property of their respective

proprietors.

Specifications are subject to change without prior notification.

Table of Content

Introduction 1

FEATU ES ....................................................................................................1

APPLICATION ................................................................................................2

PA TS NAMES AND FUNCTIONS .....................................................................3

FACTO Y DEFAULT SETTINGS .......................................................................5

Wireless AP ............................................................................................5

Hardware Connection 6

Check the LEDs: .......................................................................................6

About the Operation Modes 7

ACCESS POINT MODE....................................................................................7

WDS EPEATE MODE ................................................................................7

CLIENT MODE (INF AST UCTU E) .................................................................7

CLIENT MODE (AD-HOC) ................................................................................8

WDS BIDGE MODE .....................................................................................8

Configuration 9

STATUS ......................................................................................................10

System ..................................................................................................10

Statistics................................................................................................11

WI ELESS ..................................................................................................13

Basic Settings .......................................................................................13

Advanced Settings ................................................................................15

Security .................................................................................................19

Access Control......................................................................................21

TCP/IP ......................................................................................................24

Basic .....................................................................................................24

OTHE .......................................................................................................27

Upgrade Firmware ................................................................................27

Save/ eload Settings ...........................................................................28

Password ..............................................................................................30

System Log ...........................................................................................30

INT ODUCTION

This is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless

Access Point. The Wireless Access Point is equipped with two 10/100 M Auto-

sensing Ethernet ports for connecting to LAN and also for cascading to next

Wireless Access Point.

This Access Point provides 64/128bit WEP encryption, WPA and IEEE802.1x

which ensures a high level of security to protects users’ data and privacy. The

MAC Address filter prevents the unauthorized MAC Addresses from accessing

your Wireless LAN. Your network security is therefore double assured.

The web-based management utility is provided for easy configuration that your

wireless network connection is ensured to be always solid and hassle free.

Features

• Two LAN ports for Wireless AP cascade.

• Support WPA.

• Support AP client mode.

• Support WDS for bridge mode.

• Support data rate automatic fallback.

• Automatic channel selection.

• Client access control.

• Support 802.1x/ adius client with EAP-TLS, TKIP, AES encryption.

• Support IAPP.

• Adjustable Tx power, Tx rate, and SSID broadcast.

• Allow WEP 64/128 bit.

• Web interface management.

• Support System event log and statistics.

• MAC filtering (For wireless only).

Application

Example 1

Example 2

Parts Names and Functions

1. Front Panel: (LED Indicators)

LED Status

Indicator

Color

Solid Flashing

1 Power Green

Turns solid green when

power is applied to this

device.

N/A.

2 Status ed Turns solid red when

the device is booting,

after boot scuessfully,

the light turn off.

Link/Act.

Green

Turns solid green when

connected and

associated to at least a

client station.

eceiving/

Sending data

WEP/WP

Orange

Turns solid orange

when wireless security

is enabled.

N/A

3~6

Wireless

MAC Ctrl

Orange

Turns solid orange

when MAC Control is

enabled.

N/A

WDS

Orange

Turn solid orange

when WDS is enabled.

N/A

7 LAN 1

8 LAN 2

Green

Turns solid green when

linked to a local

network.

eceiving/

Sending data

Table 1: LED Indicators

2. ear Panel: Connection Ports

Port/button Functions

A 12V DC Connects the power adapter plug

B LAN1 Connects to Ethernet

C LAN2 Connects to Ethernet

(Factory)

ESET

Press over 3 seconds to reboot this device.

Press for over 10 seconds to restore factory

settings.

Performing

the Factory eset will erase all

previously entered device settings.

Table 2: Connection Ports

Factory Default Settings

Setting Wireless Access Point

Device Name Wireless AP

SSID Default value: 802.11g-AP

Channel 11

WEP Default value: Disabled

IP Address 192.168.1. 254



HA DWA E CONNECTION

Note: Before you starting hardware connection, you are advised to find an

appropriate location to place the Access Point. Usually, the best place for the

Access Point is at the center of your wireless network, with line of straight to all

your wireless stations. Also, remember to adjust the antenna; usually the

higher the antenna is placed, the better will be the performance.

1. Connect to your local area network: connect a Ethernet cable to one of

the Ethernet port (LAN1 or LAN2) of this Wireless Access Point, and the

other end to a hub, switch, router, or another wireless access point.

2. Power on the device: connect the included AC power adapter to the

Wireless Access Point’s power port and the other end to a wall outlet.

Check the LEDs:

The Power and LAN # LEDs should be ON. LAN# LED will even blink if there is

traffic.

The Link/Act LED will be on in static when associated with a station and blink

whenever this AP receives data packets in the air.

If the Status LED glows after self-test , it means this Wireless Access Point

fails on self test. Please ask your dealer for technical support.

3. Configure your PC: Make sure your local PC(s) has wireless network

adapter installed.

About the Operation Modes

This device provides four operational applications with Access Point, Bridge,

Client (Ad-hoc) and Client (Infrastructure) modes, which are mutually

exclusive.

This device is shipped with configuration that is functional right out of the box. If

you want to change the settings in order to perform more advanced

configuration or even change the mode of operation, you can use the web-

based utility provided by the manufacturer as described in the following

sections.

Access Point Mode

When acting as an access point, this device connects all the stations

(PC/notebook with wireless network adapter) to a wired network. All stations

can have the Internet access if only the Access Point has the Internet

connection.

See the sample application below.

To set the operation mode to Access Point, please go to “Wireless 



Basic

Settings”, in the “Mode” field click the down arrow  to select AP mode.

WDS epeater Mode

efer to the illustration below. While acting as Bridges, AP1 (with Station 1

being associated to) and AP2 (with Station 2 being associated) can

communicate with each other through wireless interface (with WDS). Thus

Station 1 can communicate with Station 2 and both Station 1 and Station 2 are

able to access the Internet if only AP1 or AP2 has the Internet connection.

To set the operation mode to Bridge, please go to “Wireless 



Basic

Settings”, in the “Mode” field click the down arrow  to select AP mode. And

go to “Wireless 



WDS Settings” to enable WDS.

Client Mode (Infrastructure)

If set to Client (Infrastructure) mode, this device can work like a wireless station

when it’s connected to a computer so that the computer can send packets from

wired end to wireless interface.

Altri manuali per AWN-AP-54MR

Altri manuali Advantek Networks Punto di accesso wireless

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente