Aeon Labs Aeotec Z-Stick Gen5 Manuale utente
View the expanded manual:
http://aeotec.com/support
GEN5
Aeotec by Aeon Labs Door/Window Sensor.
1
The Aeotec by Aeon Labs Door/Window Sensor Gen5 provides
your Z-Wave network with the intelligence required for a modern
home automation and security system. And it does it all in a
smaller, more elegant design crafted to suit any home's decor.
The Door Window Sensor is also a security Z-Wave device
that supports Over The Air (OTA) for firmware updates.
Familiarize yourself with your Door/Window
Sensor.
Package contents:
1. Sensor Unit.
2. Bidirectional Mount Plate.
3. Magnet Unit.
4. Magnet Unit Outer Shell.
5. AAA Batteries(×2).
6. Double-Sided Mounting Tape(×6).
7. Screws(×4).
1 2 3 6 754
2
LED Latch Button
Screw HolesHitchHitch Hole
Orientation Dimples
Magnet Unit
Action Button
Security Tamper Switch
Battery Holder
Double-Sided Mounting
Tape Sticking Area
Magnet Unit
Outer Sehll
Security Tamper
Switch Hole
3
The installation of your Door Window Sensor has two major
steps: the Main Sensor and the Magnet. Your Door Window
Sensor will use wireless technology to talk to your Z-Wave
network once paired to your Z-Wave network.
Selecting where you'll place your Door/Window Sensor in your
home is just as important as the actual afxing it to the surface.
Whether it’s for security or intelligence purposes, your sensor:
1.
2.
3.
4.
Should be affixed indoors and away from sources of
moisture.
Placed within 30 meters of another Z-Wave device that is
either a gateway or not powered by batteries.
The magnet and the main sensor must be less than 2cm
apart. Main sensor must be afxed to the door or window
and the magnet must be afxed to the frame. The magnet
and the main sensor must separate when the door or
window is opened.
Should not be mounted on a metal frame.
Quick start.
Afx your Sensor plates to a surface.
The Mounting plates can be affixed using screws or double-
sided tape.
If you are using screws, attach both mounting plates to the
respective surface using the two 20mm screws provided.
If you are using double-sided tape, wipe the two surfaces clean
of any oil or dust with a damp towel. When the surface has
completely dried, peel one side of the tape back and attach it
to the corresponding section on the rear side of the mounting
plates.
With your mounting plates prepared to hold each component of
your sensor, it’s time to add it to your Z-Wave network.
With your sensor added to your Z-Wave network, it's now time
to insert each main part of your sensor into the corresponding
sensor plate.
With your Door Window Sensor now working as a part of
your smart home, you’ll be able to congure it from your home
control software or phone application. Please refer to your
software’s user guide for precise instructions on configuring
Door Window Sensor to your needs.
Adding your Sensor to your Z-Wave network.
Attach your sensor to its plates.
1.
2.
3.
4.
1.
2.
Let your Z-Wave primary controller/gateway enter into
adding/inclusion mode.
Take your Sensor near to your primary controller.
Press the Action Button once on your Sensor.
If your Door Window Sensor has been successfully added
to your Z-Wave network, its Status LED will fast blink for 2
seconds and then be solid for 2 seconds when you press the
Action Button again. If the adding was unsuccessful and the
Status LED continues to fast blink for 8 seconds and then
slow blink for 3 seconds, repeat the above steps.
Insert the larger of your two sensor parts into the large
mounting plate ensuring that the dimple on the front is on the
same side as the smaller mounting plate.
lnsert the smaller of your two sensor parts into its mounting
plate.
1.
2.
Remove your Sensor unit from its Back Mounting Plate, press
the Action Button on the back of the Sensor unit and then
release the Action Button. This will trigger and send a wake
up notication command to your controller/gateway.
If you want your Sensor to keep awake for a longer time,
press and hold the Action Button on the back of the Sensor
unit for 3 seconds, then your Sensor will wake up for 10
minutes and the Status LED will fast blink while it is awake.
4
In order to send your Sensor new configuration commands
from your Z-Wave controller or gateway, it will need to be woken
up.
Your sensor can be removed from your Z-Wave network at any
time. You'll need to use your Z-Wave network's main controller/
Send a wake up notification.
Removing your Sensor from your Z-Wave network.
Advanced functions.
1.
2.
3.
4.
Put your primary controller into device removal mode.
Unlock your Sensor from the Back Mount plate and take the
Sensor unit near to your primary controller.
Press the Action Button on your Sensor.
If your Door Window Sensor has been successfully removed
from your Z-Wave network, its Status LED will fast blink for 8
seconds and then slow blink for 3 seconds when you press
the Action Button again. If the removing was unsuccessful,
the Status LED will fast blink for 2 seconds and then be solid
for 2 seconds when you press the Action Button, repeat the
above steps.
If you want your Sensor as a non-security device in your Z-
Wave network, you just need to press the Action Button once
on Door Window Sensor when you use a controller/gateway
to add/include your Sensor.
Security or Non-security feature of your Sensor in Z-
Wave network.
Including Door/Window Sensor as a non-secure device:
In order to take full advantage of all functionality the Door
Window Sensor, you may want your Sensor is a security
device that uses secure/encrypted message to communicate in
Z-Wave network, so a security enabled controller/gateway is
needed for the Door Window Sensor to be used as a
security device.
Including Door/Window Sensor as a secure device:
gateway. To do this, please refer to the part of their respective
manuals that tell you how to remove devices from your network.
Factory Reset your Sensor.
Model number: ZW120.
Battery: Up to 1 year battery life with 2×AAA batteries.
Operating temperature: 0°C to 40°C.
Relative humidity: 8% to 80%.
Operating distance: Up to 300 feet/100 metres outdoors.
Technical specifications.
5
Warranty.
If you are in need of any technical support during or subsequent
to your products’ warranty, please get in touch with our support
team via http://aeotec.com/support. The Company you bought
this product from has also guaranteed to assist you with any
of your support needs, and you can also contact them for
accordingly.
This guarantee made by the company who you purchased the
product from includes the transfer of Aeon Labs’ full warranty to
6
You need to press the Sensor’s Action Button 2 times within
1 second when your security controller/gateway starts the
network inclusion.
If your primary controller is missing or inoperable, you may
wish to reset all of your Door Window Sensor’s settings to their
factory defaults. To do this, press and hold the Action Button
for 20 seconds and Status LED will be solid for 2 seconds to
conrm a success.
that Company. They’ve guaranteed that they’ll be able to assist
you, the Customer, with all technical support and repair needs
on our behalf.
Aeon Labs warrants to the original purchaser of Products,
that is the Company who you have purchased from, that for
the Warranty Period (as defined below), the Products will be
free from material defects in materials and workmanship. The
foregoing warranty is subject to the proper installation, operation
and maintenance of the Products in accordance with installation
instructions and the operating manual supplied. Warranty claims
must be made to the Company who you have purchased
from in writing within thirty (30) days of the manifestation of a
problem.
Aeon Labs' sole obligation under the foregoing warranty is,
at Aeon Labs' option, to repair, replace or correct any such
defect that was present at the time of delivery, or to remove the
Products and to refund the purchase price to Company.
The Warranty Period begins on the date the Products is
delivered and continues for 12 months. Any repairs under this
warranty must be conducted by an authorized Aeon Labs
service representative and under Aeon Labs' RMA policy. Any
repairs conducted by unauthorized persons shall void this
warranty.
Excluded from the warranty are problems due to accidents, acts
of God, civil or military authority, civil disturbance, war, strikes,
fires, other catastrophes, misuse, misapplication, storage
damage, negligence, electrical power problems, or modication
to the Products or its components.
Aeon Labs does not authorize any person or party to assume
Altri manuali per Aeotec Z-Stick Gen5
1
Indice
