SAFETY RULES
DEVICE IN CLASS I
Always connect to a grounded socket.
CAUTION: double pole / neutral fusing.
CAUTION: for continued protection against risk of fire, replace
only with same type and rating of fuses.
Connect the ISDN port to a network termination only (NT1). It is
absolutely forbidden to connect the system to an outdoor
telecommunication line.
Connect the LAN port to an internal LAN circuit only. It is
absolutely forbidden to connect the system to an outdoor
telecommunication line.
PAN & TILT connector: this output provide a Limited Power
Sources DC output.
This equipment will be inoperable when mains power fail.
The change from cold to hot environments can cause the
formation of condensate inside the device. To avoid
malfunctioning, wait at least 2 hours before connecting the device
to the supply mains.
In case of fire, absolutely avoid using water to extinguish it.
WARNING: RISK OF ELECTRIC SHOCK
The power supply used by this device involves lethal voltage
levels.
Do not access internal parts of the device (and/or of the power
supply unit).
If objects or liquids penetrate inside the device, immediately
disconnect the power supply cable. Before using the device
again, have it checked by specialized staff.
Refer to qualified staff for service.
In case of intervention, always check that the power supply has
been completely and successfully disconnected.
ENVIRONMENTAL WARD
CAUTION: risk of explosion if batteries are replaced by an
incorrect type. Dispose of used batteries according to the
instructions.
The batteries of this equipment must be recycled by a company
in charge of this activity, a company qualified for the disposal of
dangerous materials or by using containers provided for the
separate collection of worn out batteries.
This equipment may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling
of this product. For more detailed information about recycling of
this product, please contact your local city office, your household
waste disposal or the dealer where you purchased this product.
CLEANING
To clean the device use a soft cloth either dry or moistened with a
little detergent. Never use any type of solvents, such as alcohol or
gasoline, to avoid damaging the finish.
REGIONAL REQUIREMENTS
Laitte on liitettävä suojamaadoituskoskettimilla varustettuun
pistorasiaan.
Apparatet må tilkoples jordet stikkontakt.
Apparaten skall anslutas till jordat uttag.
INSTALLATION WARNING FOR RACK MOUNT USAGE
Tmra – The manufacturer’s maximum recommended ambient
temperature is 40 °C.
Elevated Operating Ambient Temperature – If installed an a
closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be grater than room
ambient. Therefore consideration should be given to installing
the equipment in an environment compatible with the
manufacturer’s maximum rated ambient temperature (Tmra).
Reduce Air Flow – Installation of equipment in a rack should be
such that the amount of air flow required for safe operation of
the equipment is not compromised.
Mechanical Loading – Mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due
to uneven mechanical loading.
Circuit Overloading – Consideration should be given to the
connection of the equipment to the supply circuit and the effect
that overloading of circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this
concern.
Reliable earthing – Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to
supply connection other than direct connection to the branch
circuit (e.g., use of power strips).
WARNINGS
CAUTION: many of the components used in this device are
sensitive to electrostatic charge.
In case of manipulation of the connection cables, disconnect the
power supply and avoid direct contacts with the connector
terminals.
When handling electronic components, to eliminate any static
electricity touch a grounded surface. If possible, wear a
grounding arm band.
Failure to comply with these warnings could cause permanent
damage to device.
EN 55022 Class A COMPLIANCE
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may
required to take adequate measures.
FCC 15 Class A COMPLIANCE
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
6
