Aewin CB-6971 Manuale utente
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
1
Networking Control Board
Model Number CB-6971
AMD®Geode®LX800 Networking Control Board with four LAN
or three LAN and four switch
User’s Manual
Version 1.0
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
2
© Copyright 2006. All Rights Reserved
User’s Manual Edition 1.0,Aug 2006
This document contains proprietary information protected by copyright. All rights are reserved; no
part of this manual may be reproduced, copied, translated or transmitted in any form or by any means
without prior written permission of the manufacturer.
The content of this document is intended to be accurate and reliable; the original manufacturer assumes
no responsibility for any inaccuracies that may be contained in this manual. The original
manufacturer reserves the right to make improvements to the products described in this manual at any
time without prior notice.
Trademarks
IBM, EGA, VGA, XT/AT, OS/2 and PS/2 are registered trademarks of International business Machine
Corporation
Award is a trademark ofAward Software International, Inc
Intel is a trademark of Intel
RTL is a trademark of Realtek
VIA is a trademark of VIA Technologies, Inc
Microsoft, Windows, Windows NT and MS-DOS are either trademarks or registered trademarks of
Microsoft Corporation
All other product names mentioned herein are used for identification purpose only and may be
trademarks and/or registered trademarks of their respective companies
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this document, the manufacturer
and distributor assume no liability resulting from errors or omissions in this document, or from the use
of the information contained herein.
For more information on CB-6971 or otherAEWIN products, please visit our website
http://www.aewin.com.tw.
For technical supports or free catalog, please send your inquiry to
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
3
Table of Contents
Chapter 1. General Information.................................................................................4
1.1 Introducing.........................................................................................................4
1.2 Specification ......................................................................................................4
1.3 Order Information..............................................................................................5
1.4 Packaging...........................................................................................................5
1.5 Precautions.........................................................................................................5
1.6 Board Layout .....................................................................................................7
1.7 Board Dimension...............................................................................................7
Chapter 2. Connector/Jumper Configuration...........................................................9
2.1 Connector/Jumper Location and Definition.......................................................9
2.2 Connector and Jumper Setting.........................................................................10
Chapter 3 BIOS Setup...............................................................................................16
3.1 Quick Setup......................................................................................................16
3.2 Entering the CMOS Setup Program.................................................................17
3.3 Menu Options...................................................................................................18
3.4 Standard CMOS Features Setup ......................................................................19
3.5 Advanced BIOS Features Setup.......................................................................20
3.6 Advanced Chipset Features Setup....................................................................22
3.7 Integrated Peripherals ......................................................................................22
3.8 PNP/PCI Configuration ...................................................................................24
3.9 PC Health Status Configuration Setup.............................................................25
3.10 Load Optimized Defaults...............................................................................26
3.11 Set User Password..........................................................................................26
3.12 Save and Exit Setup.......................................................................................27
3.13 Exit Without Saving.......................................................................................28
Chapter 4. Utility & Driver Installation...............................................................29
4.1 Operation System Supporting..........................................................................29
4.2 System Driver Installation ...............................................................................29
4.3 VGADriver Installation...................................................................................29
4.4 LAN Driver Installation...................................................................................30
Appendix A: Optional Accessory and Cable List....................................................32
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
4
Chapter 1. General Information
1.1 Introducing
The CB-6971 is a networking control board based on AMD Geode architecture
with CS5536 chipset supporting the LX800 CPU.
The CB-6971 is equipped with four 10/100Mbps LAN ports, or three
10/100Mbps LAN and four 10/100Mbps switch. Based on good cost and
performance, it is suitable for SMB/SOHO segment. It can really match
various applications, including Firewall, VPN, Load Balancing, IPS, IDS, etc.
1.2 Specification
zCPU: AMD Geode LX800 500MHz low power processor
zBIOS: Award® 4Mb Flash BIOS
zChipset: AMD Geode CS5536
zI/O Chipset: Winbond® 83627HG
zMemory: One 184pin DDR DIMM socket can support up to 1GB
zEnhanced IDE: One 44-pin IDE connector
zSerial port: Two RS-232 serial ports (one RJ45 connector, one pin header)
zKB/Mouse: Supports PS/2 keyboard and mouse
zUSB: One USB2.0/1.1 port
zMini PCI Expansion: One Mini PCI socket
zDisplay: Support CRT
zEthernet: Four Realtek® 8139CL+ 10/100Mbps
zDigital I/O: Four digital input and four digital output
zSSD interface: One 50-pin CompactFlashTM TYPE II socket
zWatchdog timer: Can generate a system reset, support software selectable
timeout interval
zSystem Monitoring: Built in W83627HG; support temperatures, voltage
monitoring function
zPower supply voltage: Single +5V (+4.75V to +5.25V) power supply
zMax. Power Requirements: 30W
zOperating temperature: 32 to 140℉（0 to 60℃）
zBoard size: 8”(L) x 5.75”(W) (203mm x 146mm)
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
5
1.3 Order Information
We offer various combination of CB-6971 control board according to LAN difference,
it is to meet various need in the market.
Model Description
CB-6971A-050 AMD Geode LX800 Low Power Control Board with Four 10/100 LAN
CB-6971B-050 AMD Geode LX800 Low Power Control Board with Three 10/100 LAN
and Four 10/100 switch
MB06018-1-01 Adapter Module of VGA header
46-I0002X6-00 2mm, 20cm cable of MB06018
1.4 Packaging
Please make sure that the following items have been included in the package
before installation.
1. CB-6971 Control Board
2. Quick Installation Guide (Optional)
3. Cables (Optional)
4. CD-ROM that contains the following folders:
(1) Manual
(2) System Driver
(3) Ethernet Driver
(4) Utility Tools
If any item of above is missing or damaged, please contact your dealer or
retailer from whom you purchased the CB-6971. Keep the box and carton
when you probably ship or store CB-6971 in near future. After you unpack the
goods, inspect and make sure the packaging is intact. Do not plug the power
adapter to the main board of CB-6971 if you already find it appears damaged.
Note: Keep the CB-6971 in the original packaging until you start
installation.
1.5 Precautions
Please make sure you properly ground yourself before handling the CB-6971
control board or other system components. Electrostatic discharge can be
easily damage the CB-6971 control board.
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
6
Do not remove the anti-static packing until you are ready to install the CB-6971
control board.
Ground yourself before removing any system component from it protective
anti-static packaging. To ground yourself, grasp the expansion slot covers or
other unpainted parts of the computer chassis.
Handle the CB-6971 control board by its edges and avoid touching the
components on it.
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
7
1.6 Board Layout
1.7 Board Dimension
CB-6971A-050
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
8
CB-6971B-050
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
9
Chapter 2. Connector/Jumper Configuration
2.1 Connector/Jumper Location and Definition
User’s Manual
AEWIN Technologies Co., Ltd Aug, 2006
10
2.2 Connector and Jumper Setting
CN1: Reset button
Pin Define
1 Reset #
2 GND
CN2: External power jack
Pin Define
1 +5V
2 Ground
CN3: COM1 RJ45 connector
Pin Define
1 CTS#
2 DTR#
3 TXD#
4 Console Detect#
5 GND
6 RXD#
7 DSR#
8 RTX#
CN4/5/6/7: 10/100 RJ45 connector
Pin Define
1 TX+
2 TX-
3 RX+
4 Chassis Ground
5 Chassis Ground
6 RX-
7 Chassis Ground
8 Chassis Ground
CN8: Four port switch
Pin Define
1 TX+
2 TX-
3 RX+
4 Chassis Ground
5 Chassis Ground
6 RX-
7 Chassis Ground
8 Chassis Ground
CN10: VGA connector
Indice
Altri manuali Aewin Hardware di rete
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
