Affinity iLumaLight Manuale utente
© 2016 1B5997540 REV A
Français p. 13
Español p. 7
Owners Manual
www.AffinitySeats.com
2For product information and videos visit:
GETTING STARTED
Remove night light from packaging and make sure all parts are included before
starting installation.
“+” Battery clip
C-Cell battery
(Not Included)
Photo sensor lens cover
Photo sensor
Cover
“–” Battery clip
Rubber gasket
Attachment arm
Tab
PARTS
iLumaLight™ toilet seat night light provides an 8-hour cycle with the perfect
amount of illumination to help eliminate disruption of normal sleep patterns.
iLumaLight™ only works with toilet seat models:
• Bemis 200E3 (Round) and 1200E3 (Elongated)
• Church 300E3 (Round) and 380E3 (Elongated)
Requires one alkaline 1.5V C-cell battery, not included.
NOT INCLUDED
www.AffinitySeats.com 3
For product information and videos visit:
IMPORTANT NOTE:
Installing the battery backwards
will prevent the product from
functioning and may damage it.
Align +/- markings on battery
with printed circuit board.
ALWAYS start with a NEW
battery. One (1) Alkaline 1.5V
C-cell is required (not included).
Open battery case by squeezing
both ends of the cover inward and
lifting to release.
Install a new C-cell battery matching
the + and - markings. When inserted
properly, the red LED light will turn
on for a few seconds and indicate
the battery is installed properly.
BATTERY INSTALLATION
1
11
2
2
–
+
3
Replace cover. Make sure rubber
gasket o-ring aligns with groove.
Make sure the photo sensor lens
cover is above the photo sensor.
www.AffinitySeats.com
4For product information and videos visit:
4
Place seat upside down on a soft
surface with the hinges facing
toward you.
Snap the iLumaLight™into place,
aligning the mounting tabs into the
grooves on the outside of hinge.
iLumaLight™ OPERATION
INSTALLING iLumaLight™ ON SEAT
1
22
21
Install the seat using the instructions provided with the seat.
Setting the Desired Start Time
At the desired start time, press the
black button to start the cycle.
Once the start time has been set,
iLumaLight™ will automatically turn
on at that same time each night.
NOTE: In a bright room, the night
light will turn on for a few seconds
and then turn off. In a dark room,
the night light will turn on after a few
seconds and stay on for the 8-hour
cycle.
NOTE: The cycle start time can be
reset at any time by pressing the
black button or by removing and
reinstalling the battery.
www.AffinitySeats.com 5
For product information and videos visit:
REMOVING iLumaLight™ FROM SEAT
Grasp iLumaLight™and gently roll
backwards away from the back of
the seat.
Once the mounting tabs have
separated from the seat, lift
iLumaLight™ straight up to remove.
1
1
2
2
CLEANING
When cleaning, Bemis recommends removing the seat from the bowl and
removing the iLumaLight™from the seat first. Wipe external surfaces with a
damp cloth, then remove the cover and dry any liquid that may be inside.
NOTE: DO NOT spray with toilet bowl cleaners or other liquids.
LOW BATTERY INDICATOR
When battery life is low, the iLumaLight™will go into a “low battery” mode.
The brightness of the night light will cycle between bright and dim every four
seconds during the “ON” period, showing that the battery is getting weak.
When battery voltage is reduced below functional levels, the light will stop
operating. Pressing the black button may start it again, but subsequent use
without replacing the battery will eventually stop the iLumaLight from operating.
NOTE: iLumaLight™ will be more difficult to remove the first time, but will
remove more easily with repeated removal.
Before removing the iLumaLight™, remove the seat using the Easy•Clean &
Change® feature. Flip up the hinge caps and lift the seat from the bowl. Place
the seat upside down on a soft surface.
www.AffinitySeats.com
6For product information and videos visit:
Problem Solution
Cannot close
case
1. Make sure the battery is installed correctly.
2. Make sure top cover is properly aligned.
3. Make sure rubber gasket o-ring is correctly placed.
Will not turn on 1. Make sure the battery is installed correctly. Replace if
needed.
2. Press black button to restart 8-hour light cycle at desired
time.
3. Make sure it is dark enough for the light sensor to operate
properly.
Inside of case
is wet
1. Open case and remove battery. Dry terminals.
2. Clean the battery clips. Dry any moisture found on inside
of the case.
3. Allow to fully dry by keeping the case open for an
extended period of time.
4. Reinstall battery, aligning with + and - markings.
IMPORTANT! Liquids inside the product may cause
contact corrosion and failure of product to operate.
Liquids can damage electronic components. DO NOT
immerse in any liquids or spray with any liquids. The
product enclosure is liquid resistant, but not sealed. Make
sure the rubber gasket o-ring is seated in the enclosure
groove and align the enclosure tabs properly when
assembling after inserting the battery.
Turns On/Off
at the wrong
times
1. Press the black button at the desired start time to restart
the 8-hour “ON” cycle.
2. Make sure the sensor lens on the top of the case is clean
and not blocked by any debris.
TROUBLESHOOTING
LIMITED WARRANTY
This product is guaranteed against defect in material and workmanship for one
year. If this product is defective, your exclusive remedy will be a replacement
product of equal value. Expenses for removal and replacement are not
covered.
This guarantee does not apply to any products which are modified in any way
or used in any type of installation or unit other than conventional water closets.
We assume no liability for toilet seats modified or installed on anything other
than conventional water closets.
Français p. 13
Español p. 7
Manual de Propietario
www.AffinitySeats.com
8Para más información y video del producto visita:
INTRODUCCIÓN
Retire luz de la noche del empaque y asegúrese de que todas las partes estén
incluidas antes de comenzar la instalación.
“+” Clip de batería
Batería C
(No incluida)
Cubierta del fotosensor
Fotosensor
Cubierta
“–” Clip de batería
Empaque de goma
Brazo de unión
Pestaña
PARTES
El asiento iLumaLight™ con luz de noche ofrece un ciclo de 8 horas con la
cantidad perfecta de iluminación que ayuda a eliminar la interrupción de los
patraones normales de sueño.
iLumaLight™ solo funciona con los modelos de asientos:
• Bemis 200E3 (Redondo) y 1200E3 (Alargado)
• Church 300E3 (Redondo) y 380E3 (Alargado)
Requiere una batería C de 1.5V no incluida.
NO INCLUÍDA
www.AffinitySeats.com 9
Para más información y video del producto visita:
NOTA IMPORTANTE:
La instalación de la batería al
revés evitará que el producto
funcione y éste puede ser
dañado. Alínea las marcas +/-
de la batería con la placa del
circuito marcado. Comience
SIEMPRE con una batería
NUEVA. Se requiere de una (1)
batería C de 1.5V (no incluida).
Abra la caja de la batería apretando
ambos extremos de la cubierta hacia
adentro y levante para liberar.
Instale la nueva batería C
emparejando las marcas + y -.
Cuando se inserte correctamente, la
luz roja LED se encenderá durante
unos segundos, esto indicará
que la batería está correctamente
instalada.
INSTALACIÓN DE BATERÍA
1
11
2
2
–
+
3
Vuelva a colocar la cubierta.
Asegúrese de que el empaque de
goma se alinee con la ranura del
anillo. Asegúrese de que la cubierta
del fotosensor esté por encima del
fotosensor.
www.AffinitySeats.com
10 Para más información y video del producto visita:
Coloque el asiento en posición
invertida sobre una superficie blanda
con las bisagras hacia usted.
Coloque el iLumaLight™en su lugar,
alineando las pestañas de montaje
en las ranuras de la parte exterior de
las bisagras.
FUNCIONAMIENTO iLumaLight™
INSTALACIÓN DE iLumaLight™ EN ASIENTO
1
22
21
Instale el asiento utilizando las instrucciones proporcionadas con el asiento.
Ajuste la Hora de Inicio Deseada
A la hora de inicio deseada, pulse el
botón negro para iniciar el ciclo.
Una vez que se ha estableciodo la
hora de inicio, iLumaLight™ se
encenderá automáticamente a la
misma hora cada noche.
NOTA: En una habitación iluminada,
la luz de noche se encenderá durante
unos segundos y se apagará. En un
cuarto oscuro, la luz de noche se encenderá al cabo de unos segundos y
permanecerá encendida durante el ciclo de 8 horas.
NOTA: La hora de inicio del ciclo se puede restablecer en cualquier momento
pulsando el botón negro o quitando y poniendo la batería.
Indice
Lingue:
Manuali Apparecchio di illuminazione popolari di altre marche
Emos
Emos CLASSIC ZY1431T Manuale utente
Westinghouse
Westinghouse Outdoor Lighting Fixture Manuale utente
Hedler
Hedler C 12 silent Manuale utente
Blizzard Lighting
Blizzard Lighting Puck: CSI Manuale utente
Energetic Lighting
Energetic Lighting ELYSL-5004 Series Manuale utente
Lightmaxx
Lightmaxx Shaft 5R Manuale utente
Cooper Lighting
Cooper Lighting Halo L3232E Manuale utente
Stageline
Stageline ODW-2410RGBW Manuale utente
Light Sky
Light Sky Tornado Series Manuale utente
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente
Lightolier
Lightolier Lytespan 83ED17S Manuale utente
Lightolier
Lightolier Calculite CS8226 Manuale utente