Afron HD1100N Manuale utente
HD1100N
Parts Manual
PART III
Edition: April-2005
www.afron.com
T. 972-4-6371203
1
INDEX
INDEX…………………………………………………………………………………………… 1-2
INTRODUCTION……………………………………………………………………………….3
MACHINE DETAILS…………………………………………………………………………. 4
INDEX OF SECTIONS SCHEMATIC.........................................................……………….….5
A- SAW ASSEMBLY - SCHEMATIC ……………………...…..…………………………….6
A- SAW ASSEMBLY - PARTS LIST...…..………………………………………………….…7
B- MAIN ROTATION SHAFT - SCHEMATIC.....................…......………………………….8
B- MAIN ROTATION SHAFT- PARTS LIST..............................……….……………………9
C- ROTATION MOTOR – SCHEMATIC……………………........…..……………………...10
C- ROTATION MOTOR - PARTS LIST......…..……..…………………………………….…11
D- WIDTH CYLINDER SCHEMATIC ……...………………………………….…………….12
D- WIDTH CYLINDER PARTS LIST……...………..………………………….…………….13
E- VER/HOR CYLINDER – SCHEMATIC …………………….…………………………… 14
E- VER/HOR CYLINDER – PARTS LIST …………………………………………………...15
F-ENGINE HOOD CYLINDER- SCHEMATIC AND PARTS LIST …………….……….. 16
G- LIFT CYLINDER – SCHEMATIC AND PARTS LIST ….…….……………………… 17
H- COOLING FAN- SCHEMATIC AND PARTS LIST……………..………...……………. 18
I- REAR AXLE CYLINDER- SCHEMATIC AND PARTS LIST.………...……………… 19
J- REAR AXLE PIVOT - SCHEMATIC AND PARTS LIST………………….……………20
K- FRONT AXLE HUB- SCHEMATIC AND PARTS LIST…..……………...……………. 21
L- STEERING CYLINDER AND TIE ROD- SCHEMATIC ……………...………………...22
L- STEERING CYLINDER AND TIE ROD- PARTS LIST ……………...………………... 23
M-FRONT AXLE CYLINDER- SCHEMATIC AND PARTS LIST………………………..24
N- FRONT AXLE PIVOT- SCHEMATIC AND PARTS LIST………………..…………... 25
O- FRONT PUMP COUPLING- SCHEMATIC AND PARTS LIST…………………...….. 26
HYDRAULIC SYSTEM- CONTROL CIRCUIT SCHEMATIC ….………………..……… 27
HYDRAULIC SYSTEM- CONTROL CIRCUIT PARTS LIST….……………… …………28
HYDRAULIC SYSTEM-SAW CIRCUIT SCHEMATIC……………………....….……….. 29
HYDRAULIC SYSTEM-SAW CIRCUIT PARTS LIST……………………....….……….. 30
HYDRAULIC SYSTEM –ROTATION CIRCUIT SCHEMATIC…………………………. 31
HYDRAULIC SYSTEM –ROTATION CIRCUIT PARTS LIST………………………….. 32
INDEX-CONT .
2
HYDRAULIC SYSTEM –HYDROSTATIC DRIVE SCHEMATIC ……………………… 33
HYDRAULIC SYSTEM –HYDROSTATIC DRIVE -PARTS LIST ……………………… 34
HYDRAULIC SYSTEM –POWER STEERING SCHEMATIC AND PARTS LIST.……..35
HYDRAULIC SYSTEM –COOLING FAN SCHEMATIC AND PARTS LIST....……….. 36
SPECIAL TOOLS……………………………………………………………………………….37
NOTE……………………………………………………………………………………………..38
3
Dear Customer :
This parts manual is Part III from your machine documentation file.
Before attempting to service or operate the machine make sure to read and understand
The “General Pruning Manual” - Part I and the “Machine Manual” Part II.
This parts manual will guide you in the event that spare parts are needed for your Machine.
We urge you to use only original spare parts.
The first page contains all the specific information of your machine.
For example:Machine Serial Number, Date of Purchase Etc.
When making any parts inquiry, the following information will help us to serve you
quickly and efficiently:
1. Customer name.
2. Machine model.
3. Machine serial number.
4. Part number.
5. Part description.
This manual contains only the “common wear” parts. If you are in need of a part that
is not listed in this manual, please contact us and we will be happy to assist you.
For any technical assistance, please contact your local dealer or our
Technical Department:
ISRAEL: Phone # ++972-4-63713203 or Fax #++972-4-6370246.
USA: Phone #1-559-686-2844 or Fax # 1-559-685-1006.
As our policy is of continuous improvement, we reserve the right to change
Specification and design without notice.
IMPORTANT:
Read and understand the ”Machine Operating Manual” and the “General Pruning
Manual ” before attempting to do any service work on the machine or to operate it.
Service work or any operating of this equipment should be performed only by qualified
And trained personnel.
Do not attempt to change any of the original settings of the machine, or run the machine
without ALL of the original covers on.
Do not operate the machine if it is not in safe operating condition.
ALWAYS PUT SAFETY FIRST
4
MACHINE DETAILS
Machine model:…........................…… Machine S/N:………………………………
Date of purchase:……………………………………………………………………….….
Sold by (dealer):…………………………………………………………………………..
Purchaser’s Name:…........................……………………………………………………..
Phone number:………………………. Fax number:……………………………….
E-mail: ……………………………………………………………………………………
Address: ………………………………………………………………………….………..
City:...........................................……….State:....................................……………………..
Postal code:……………………………Country:………………………………………….
……………………………………………………………………………………………………
……………………………………………………………………………………………………
……………………………………………………………………………………………………
……………………………………………………………………………………………………
……………………………………………………………………………………………………
……………………………………………………………………………………………………
……………………………………………………………………………………………………
……………………………………………………………………………………………………
……………………………………………………………………………………………………
…………………………………………………………………………
5
INDEX OF SECTIONS
6
HD1100N-SECTION -A – SAW ASSY.
SCHEMATIC
7
HD1100N-SECTION- A – SAW ASSY.
PARTS LIST
REF. NO. DESCRIPTION PART NO.
1 SAW BEARING HOUSE 00100135
2 SAW SHAFT BEARING 6007-2RS 87006007
3 SAW BEARING SPACER 00100131
4 SAW PULLEY 00160069
5 SAW WASHER 00100132
6 SAW SHAFT - SHORT 00160072
7 SAW SHAFT NUT 1”NC 861016NC
8 SAW NUT STOPPER 00160089
9 SAW BLADE 24” 00100133
10 CUTTING HEAD FRAME – 11 FT 00145182
11 SAW PULLEY COVER 00100111
12 SPRING WASHER 3/8” 86600600
13 BOLT 3/8” NC x 3 /4” 85106012
14 FLAT NUT – SHORT 00100128
15 FLAT NUT- LONG 00100129
16 BELT BX124 048BX124
17 WASHER 1 /4” 86500400
18 SPRING WASHER 1 /4” 86600400
19 BOLT 1 /4”NC x 1 /2” ALEN 85704008
8
HD1100N- SECTION -B – MAIN ROTATION SHAFT
SCHEMATIC
9
HD1100N-SECTION- B – MAIN ROTATION SHAFT
PARTS LIST
REF.
NO. DESCRIPTION PART NO.
1 CUTTING ARM FRAME - LEFT 00145100
1 CUTTING ARM FRAME - RIGHT 00145110
2 BEARING 6015-2RS 87006015
3 SPACER 00160075
4 ROTATION ASSEMBLY (COMPLETE) 00195038
5 BEARING 6007 – 2RS 87006007
6 SAW ROTATION SHAFT 00195035
7 KEY 00195051
8 SNAP RING FOR SHAFT 35 876CI035
9 SNAP RING FOR SHAFT 75 876CI075
10 SAW MOTOR MOUNT FLANGE 00195034
11 MAIN SAW PULLEY 00195011
12 CONNECTOR 00115028
13 WASHER 00160071
14 BOLT 5/16”NC x 1 1 /4 “ 85105020
15 SPRING WASHER 5/16” 86600500
16 BOLT 1/2 NC x 1 1/4" 85108020
17 SPRING WASHER 1/2" 86600800
18 SAW MOTOR 00165101S
19 BOLT 7/16” NC x 1 1/4" 85107020
20 WASHER 7/16” 86500700
21 CUTTING HEAD FRAME - 11 FT. 00145182
22 DRIVE BELT BX-124 048BX124
23 BOLT 3/8”NC X 1 ¾" 85106028
24 SPRING WASHER 3/8” 86600600
25 BOLT 3/8”NC x 1” 85106016
26 COVER 00165105
27 BOLT 3/8”NC x 1 1/2" 85106024
28 ROTATION SHAFT 00195036
29 GEAR 00195037
30 BOLT 3/8” X 1 ¼” 85106020
Indice
