AIC SB122-PH Manuale utente

SB122-PH

Storage Server Barebone

User's Manual

UM_SB122-PH_v.2_122215

contents

CONTENTS

PREFACE�� i

SAFETY INSTRUCTIONS�� ii

Chapter 1� Prodcut Introduction �� 1

1�1 Box Content ��1

1.2 Specications ��2

1�3 General Information��3

Chapter 2� Hardware Installation�� 6

2�1 Central Processing Unit (CPU) ��6

2�2 System Memory��14

2�3 Removing and Installing Chassis Top Cover ��18

2�4 Removing/Installing a Drive Tray/ Hard Drive/ Drive Slot Map��19

2�5 Removing and Installing a Fan Module ��20

2�5�1 Removing a fan module��20

2�6 Removing and Installing a PSU Module ��22

2�7 Replacing the PCIe Card and Riser Assembly ��23

2�8 Tool-less Blade Slide Installation introduction ��25

Chapter 3� Motherboard Settings�� 29

3�1 Motherboard block diagram ��29

3�2 Motherboard block diagram ��30

3�3 Motherboard Content List��31

3�4 Internal Connectors/Jumpers ��32

3�5 LEDs��39

Chapter 4. BIOS Conguration and Settings �� 42

4�1 Updating BIOS��44

Chapter 5. BMC Conguration and Settings�� 46

5�1 Method 1 (Use the BIOS setup) ��46

5�2 Method 2 (Use a Dos tool - Syscheck)��49

5�3 Connect to BMC ��51

5�4 Updating BMC Firmware��55

contents

Chapter 6� Hardware Introduction�� 56

6�1 BACKPLANE HARDWARE INTRODUCTION��56

6�2 RISER CARD HARDWARE INTRODUCTION ��59

Chapter 7� Technical Support�� 63

This document contains proprietary information about

AIC products and is not to be disclosed or used except in

accordance with applicable agreements.

PREFACE

• Copyright

No part of this publication may be reproduced, stored in a retrieval system,

or transmitted in any form or by any means, electronic, mechanical, photo-

static, recording or otherwise, without the prior written consent of the

manufacturer.

• Trademarks

All products and trade names used in this document are trademarks or

registered trademarks of their respective holders.

• Changes

The material in this document is for information purposes only and is subject

to change without notice.

• Warning

1. A shielded-type power cord is required in order to meet FCC emission

limits and also to prevent interference to the nearby radio and television

reception. It is essential that only the supplied power cord be used.

2. Use only shielded cables to connect I/O devices to this equipment.

3. You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to

operate the equipment.

• Disclaimer

AIC shall not be liable for technical or editorial errors or omissions

contained herein. The information provided is provided "as is" without

warranty of any kind. To the extent permitted by law, neither AIC or its

affiliates, subcontractors or suppliers will be liable for incidental, special or

consequential damages including downtime cost; lost profits; damages

relating to the procurement of substitute products or services; or damages

for loss of data, or software restoration. The information in this document is

subject to change without notice.

SAFETY INSTRUCTIONS

• Before getting started, please read the following important cautions:

• All cautions and warnings on the equipment or in the manuals should be

noted.

• Most electronic components are sensitive to electrical static discharge.

Therefore, be sure to ground yourself at all times when installing the

internal components.

• Use a grounding wrist strap and place all electronic components in

static-shielded devices. Grounding wrist straps can be purchased in any

electronic supply store.

• Be sure to turn off the power and then disconnect the power cords from

your system before performing any installation or servicing. A sudden

surge of power could damage sensitive electronic components.

• Do not open the system’s top cover. If opening the cover for

maintenance is a must, only a trained technician should do so.

Integrated circuits on computer boards are sensitive to static electricity.

Before handling a board or integrated circuit, touch an unpainted

portion of the system unit chassis for a few seconds. This will help to

discharge any static electricity on your body.

• Place this equipment on a stable surface when install. A drop or fall

could cause injury.

• Please keep this equipment away from humidity.

• Carefully mount the equipment into the rack, in such manner, that it

won’t be hazardous due to uneven mechanical loading.

• This equipment is to be installed for operation in an environment with

maximum ambient temperature below 35°C.

• The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

• Never pour any liquid into ventilation openings. This could cause re or

electrical shock.

• Make sure the voltage of the power source is within the specification

on the label when connecting the equipment to the power outlet. The

current load and output power of loads shall be within the specication.

• This equipment must be connected to reliable grounding before using.

Pay special attention to power supplied other than direct connections,

e.g. using of power strips.

• Place the power cord out of the way of foot traffic. Do not place

anything over the power cord. The power cord must be rated for the

iii

• product, voltage and current marked on the product’s electrical ratings

label. The voltage and current rating of the cord should be greater than the

voltage and current rating marked on the product.

• If the equipment is not used for a long time, disconnect the equipment from

mains to avoid being damaged by transient over-voltage.

• Never open the equipment. For safety reasons, only qualified service

personnel should open the equipment.

• If one of the following situations arise, the equipment should be checked by

service personnel:

1. The power cord or plug is damaged.

2. Liquid has penetrated the equipment.

3. The equipment has been exposed to moisture.

4. The equipment does not work well or will not work according to its user

manual.

5. The equipment has been dropped and/or damaged.

6. The equipment has obvious signs of breakage.

7. Please disconnect this equipment from the AC outlet before cleaning.

Do not use liquid or detergent for cleaning. The use of a moisture sheet or

cloth is recommended for cleaning.

• Module and drive bays must not be empty! They must have a dummy cover.

Product features and specications are subject to change without notice.

CAUTION :

risk of explosion if battery is replaced by an incorrect type.

dispose of used batteries according to the instructions.

After performing any installation or servicing, make sure the

enclosure are lock and screw in position, turn on the power.

Chapter 1 Product Introduction

SB122-PH User's Manual

1�1 Box Content

Before removing the subsystem from the shipping carton, visually inspect the

physical condition of the shipping carton. Exterior damage to the shipping

carton may indicate that the contents of the carton are damaged. If any

damage is found, do not remove the components; contact the dealer where

the subsystem was purchased for further instructions. Before continuing, rst

unpack the subsystem and verify that the contents of the shipping carton are

all there and in good condition.

• Enclosure( Power supply, fan, 10 x 2.5'' HDD tray included)

• Power cord • Screws kit x 1set

• Slide rail x 1set

♦PACKAGE CONTENT MAY VARY PER REGION.

Chapter 1� Prodcut Introduction

• 2.5’’ HDD Tray

Chapter 1 Product Introduction

1.2 Specications

Chapter 1 Product Introduction

SB122-PH User's Manual

1�3 General Information

SB122-PH is a 1U Storage Server Barebone with Motherboard Phoenix/

10 x 2.5”HDD hot swap Bays at front and single 12G expander on HDD

Backplane which is a high performance Storage Server Barebone.

• Front Panel

Indice

Manuali Server di archiviazione di rete popolari di altre marche

HP NetStorage 6000 Manuale utente

Seagate

Seagate U10 ST320423A Manuale utente

Synology

Synology RackStation RS816 Manuale

D-Link

D-Link ShareCenter Pro DNS-1200-05 Manuale utente

Avid Technology

Avid Technology VideoRAID ST Guida di sicurezza

Western Digital

Western Digital My Cloud Home Duo Manuale utente

PrimeArray

PrimeArray 4xxx Manuale utente

Buffalo

Buffalo TeraStation WSS WSH5010N6 Manuale utente

Planex

Planex MZK-NAS01SG Manuale utente

Intel

Intel SS4000-E - Entry Storage System NAS Server Manuale utente

Synology

Synology RS2212+ Manuale utente

Allnet

Allnet ALL69000 Manuale utente

Adaptec

Adaptec 5325301580 Manuale utente

Motorola

Motorola EXORdisk II Manuale utente

Sony

Sony XDAAI1PK Manuale utente

Cisco

Cisco Linksys NAS200 Istruzioni operative originali

Sans Digital

Sans Digital MR4UT6G Manuale utente

Dell

Dell PowerVault NX3500 Istruzioni utente