Aircatglobal VirtualFly TQ6+ Throttle Quadrant Manuale utente
TQ6+ | User's manual 1
1. PACKAGE LIST
A) TQ6+ Throttle quadrant
B) Clamp for TQ6+
C) Screws for clamp
D) Allen key
TQ6+Throttle Quadrant
USER'S MANUAL
Rev. 1.2 - November 2020
CD
1x
1x
1x
4x
A
B
2
TQ6+ | User's manual
2. CLAMP ASSEMBLY
You have two ways for assembling the clamp: (1) on the back or (2) on the bottom, to get the best position for you. If you choose the bottom position, you must
unscrew the two front rubber feet before you screw the clamp.
Connect the USB cable to the computer where the flight simulator software is running.
It is not necessary the calibration on windows because the device is calibrated from factory.
12
TQ6+ | User's manual 3
3. CONTROLS 4. CALIBRATION ON WINDOWS
Adjusting the lever’s hardness
If you want you can adjust the lever’s hardness tightening the wheels (K &
J) located on the left and the right sides of the device.
Once you have adjusted the knob, move the 2 or 4 levers (all the way at
the same time, from top to bottom, at least 10 times). This operation is
necessary to distribute adequately the same strength in the 2 or 4 levers.
It is not necessary the calibration on windows because the
device is calibrated from factory but you can use the calibra-
tion Windows tab to test the device.
K J
TQ6+ | User's manual 4
As the TQ6+control interacts with any computer as a normal HID device (Joystick), this make it compatible with any FLIGHT SIMULATOR software.
The follow tables tells how to configurate the TQ6+on the most popular FLIGHT SIMULATOR software, FSX-Prepar3D and X-Plane.
FSX-Prepar3D
5. CONFIGURATION ON FLIGHT SIMULATION SOFTWARE
Through VFTest&Calibrate-S
on Prepar3D *(only compatible with Prepar3D V3-
V4-V5). You have to use VF-Test&Calibrate-S Soft
downloadable from our web-site:
www.virtual-fly.com/en/downloads
Full functionality:
Throttle-Rev, Propeller-Fth, Mixture-CutOFF.
Full functionality: Throttle-Rev,
Propeller-Fth, Mixture-CutOFF.
Through FSX-Prepar3D
controllers menu.
Is not advisable
Only functionally:
Throttle, Propeller and Mixture.
Rev, Fth, CutOFF zones may not match
Through FSUIPC
menu on FSX-Prepar3D.
TQ6+Configuration options on FSX-Prepar3D
1. Open FSX-Prepar3D, go to Con-
trols menu, axis assignments
section and select TQ6+ from the
devices list. Assign the axes and
do the calibration according the
instructions shown.
1. Open Prepar3D, go to Controls menu, axis
assignments section and select TQ6+from the
devices list. Delete all axis assignments. Close
and open Prepar3D again to make sure that
settings have been saved.
2. Open VFTest&Calibrate-S software, go to TQ6
tab and select the device from the devices list
at right side.
3. Calibrate IDLE point and save changes.
4. VFTest&Calibrate-S has to be running when
using TQ6+because this software reads the
data from the device and send it to Prepar3D
so each time you start Prepar3D, you have to
run VFTest&Calibrate-S as well. You can use
Windows Scheduler to start VFTest&Calibrate-S
automatically.
1. Install FSUIPC if not installed.
Registration required.
2. Open FSX-Prepar3D, go to Controls
menu, axis assignments section and
select TQ6+from the devices list.
Delete all axis assignments. Close and
open FSX-Prepar3D again to make
sure that settings have been saved.
3. Go to FSUIPC Menu and assign each
axis to throttle, propeller and mixture.
Only use "Axis Throttle1,2,3,4 set".
"Axis Propeller1,2,3,4 set". And "Axis
Mixture1,2,3,4 set". Do not use: Axis
Throttle set, Axis Propeller set or Axis
Mixture set.
4. Go to Joystick calibration tab of FSUIPC
and calibrate Max, IDLE and Rev or Fth
or Cut-o.
TQ6+ | User's manual 5
TQ6+Configuration on X-Plane
X-Plane
1. Open X-Plane and go to Configuration\Joystick tab.
2. Select TQ6+and calibrate the axes if required.
3. Assign the according action to each axis:
Throttle 1 – Throttle 2 – Prop 1 – Prop 2 – Mixture 1 – Mixture 2.
THROTTLE levers configuration:
- Reverse axis unchecked.
- On Edit response curve check “Has beta/reverse detents”.
- On Edit response curve, Interp Mode select “Linear”.
- On Edit response curve adjust “Beta” and “Reverse” zones.
PROP levers configuration:
- Reverse axis checked.
- On Edit response curve check “Set feather point”.
- On Edit response curve, Interp Mode select “Linear”.
- On Edit response curve adjust “Feather point”.
MIXTURE levers configuration:
- Reverse axis checked.
- On Edit response curve check “Set mixture cuto point”.
- On Edit response curve, Interp Mode select “Linear”.
- On Edit response curve adjust “Cuto point”.
Through X-Plane Configuration\Joystick tab:
Full functionality:
Throttle-Rev, Propeller-Fth, Mixture-CutOFF.
Indice
Altri manuali Aircatglobal Controller per videogiochi
