AirLive SI-104 Manuale utente

SI-104

Smoke Sensor

User Manual

i AirLive SI-104 User Manual

No part of this publication may be reproduced in any form or by any means, whether

electronic, mechanical, photocopying, or recording without the written consent of OvisLink

Corp.

OvisLink Corp. has made the best effort to ensure the accuracy of the information in this

user’s guide. However, we are not liable for the inaccuracies or errors in this guide.

Please use with caution. All information is subject to change without notice

This product contains some codes from GPL. In compliance with GPL agreement, AirLive

will publish the GPL codes on our website. Please go to www.airlive.com and go to the

"Support->GPL" menu to download source code.

All Trademarks are properties of their respective holders.

AirLive SI-104 User Manual ii

FCC ID: ODMSI104

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna

or transmitter.

Warning

Do not dispose of electrical appliances as unsorted municipal waste, use separate

collection facilities. Contact your local government for information regarding the collection

systems available. If electrical appliances are disposed of in landfills or dumps, hazardous

substances can leak into the groundwater and get into the food chain, damaging your

health and well-being.

When replacing old appliances with new once, the retailer is legally obligated to take back

your old appliance for disposal at least for free of charge.

Table of Contents

AirLive SI-104 User Manual

iii

Table of Contents

1. Overview................................................................................................... 1

1.1 Add to/Remove from Z-WaveTM Network.......................................... 2

1.2 Z-WaveTM Notification ...................................................................... 3

1.3 Z-WaveTM Message Report.............................................................. 3

1.4 Power Up Procedure ......................................................................... 4

1.5 Over The Air (OTA) Firmware Update................................................ 4

1.6 Security Network................................................................................ 5

1.7 Test Alarm.......................................................................................... 5

1.8 Tamper Switch Feature...................................................................... 5

1.9 Battery Installation............................................................................. 6

1.10 Choosing a Suitable Location .......................................................... 6

1.11 Installation........................................................................................ 8

1.12 Z-Wave Configuration Settings ........................................................ 9

1.13 Z-Wave Supported Command Class................................................ 9

1.14 Specifications................................................................................. 10

1. Overview

AirLive SI-104 User Manual

1. Overview

The Z-Wave Plus Smoke Sensor SI-104 is designed to give early warning of developing

fires by giving off the alarm sounds from its build-in alarm horn, based on Z-WaveTM

technology.

It is the Z-WaveTM plus product, it support the security, OTA... those newest features of the

Z-WaveTM technology. Z- Z-WaveTM is a wireless communication protocol designed for

home automation, specifically to remotely control applications in residential and light

commercial environments. The technology uses a low-power RF radio embedded or

retrofitted into home electronics devices and systems, such as lighting, home access

control, entertainment systems and household appliances.

This product can be included and operated in any Z-WaveTM network with other Z-WaveTM

certified devices from other manufacturers and/or other applications. All non-battery

operated nodes within the network will act as repeaters regardless of vendor to increase

reliability of the network.

The device adopts the Z-WaveTM 500 series chip, when your Z-WaveTM network system is

all made by Z-WaveTM 500 series devices. The network system will have the advantages as

below.

•

Concurrent multi-channel support reduces external interference.

•

Better RF range, improve about 10 meters in indoor.

•

Support 100 Kbps transmit speed, speed up communication.

1. Overview

AirLive SI-104 User Manual

1.1 Add to/Remove from Z-WaveTM Network

There is one button on the device. It can be used to add, remove, reset or association from

Z-WaveTM network.

In the first time, add the device into the Z-WaveTM network. First, make sure the primary

controller is in the add mode. And then power on the device, just take out the insulation

Mylar in the back side of the device. The device will auto start the NWI (Network Wide

Inclusion) mode. And it should be included in 5 seconds. You will see the LED light ON one

second.

Notice: Including a node ID allocated by Z-WaveTM Controller means “Add” or “Inclusion”.

Excluding a node ID allocated by Z-WaveTM Controller means “Remove” or “Exclusion”.

Function

Description

Add

1. Have Z-WaveTM Controller entered inclusion mode.

2. Pressing TEST Button three times within 1.5 seconds to enter the

inclusion mode.

3. After add successful, the device will wake to receive the

setting command from Z-WaveTM controller about 20

seconds.

Remove

1. Have Z-WaveTM Controller entered exclusion mode.

2. Pressing TEST Button three times within 1.5 seconds to enter the

exclusion mode.

Node ID has been excluded.

Reset

Notice: Use this procedure only in the event that the primary

controller is lost or

otherwise inoperable.

1. Pressing TEST Button four times within 1.5 seconds and do not

release the tamper key in the 4th pressed and the red LED will

light ON.

2. After the red LED flash 9 times, release the button within 2

seconds.

3. IDs are removed and all settings will reset to factory default.

Association

1. Have Z-WaveTM Controller entered association mode.

2. Pressing TEST Button three times within 1.5 seconds to enter the

association mode.

Note: The device supports 1 group. This group is for receiving the report

message, like triggered event etc. These groups support 8 nodes

maximum.

Failed or success in add/remove the node ID can be viewed from Z-WaveTM

Controller.

Notice 1: Always RESET a Z-WaveTM device before trying to add it to a Z-WaveTM network.

1. Overview

AirLive SI-104 User Manual

Notice 2: When the device into NWI mode, the sensor functionality will useless. The NWI mode will

timeout after 30 seconds. You can press the tamper key 3 times to abort the NWI mode.

1.2 Z-WaveTM Notification

After the device adding to the network, it will wake-up once per day in default. When it

wake-up it will broadcast the “Wake Up Notification” message to the network, and wake-up

10 seconds for receive the setting commands.

The wake-up interval minimum setting is 30 minutes, and maximum setting is 120 hours.

And the interval step is 30 minutes.

If the user wants to wake-up the device immediately, please press the tamper key once.

The device will wake-up 10 seconds.

1.3 Z-WaveTM Message Report

When the smoke sensor detects, the device will report the trigger event and also report the

battery status.

In default the device will using Notification Report to represent the trigger event, it can be

changed to Sensor Binary Report by setting the configuration NO. 7 Bit4 to 1.

1.3.1. Smoke Detected/Test Report

When the Smoke Sensor detects smoke, the device will unsolicited to send the smoke

detected (0x02) report to the nodes in the group 1. When the device is in alarm test mode,

the device will unsolicited to send the Smoke Sensor test (0x03) report to the nodes in the

group 1.

Notification Report (V4)

Notification Type: Smoke (0x01)

Event: Smoke detected, Unknown Location (0x02)

Smoke Alarm Test (0x03)

Sensor Binary Report (V2)

Sensor Type: Smoke (0x02)

Sensor Value: 0xFF

1.3.2. Tamper Report

When the tamper is pressed, the device will into the alarm state. In that state, if tamper is

1. Overview

AirLive SI-104 User Manual

released, the yellow LED will light on and the device will unsolicited to send the report to the

nodes in the group 1.

Notification Report (V4)

Notification Type: Home Security (0x07)

Event: Tampering. Product covering removed (0x03)

Sensor Binary Report (V2)

Sensor Type: Tamper (0x08)

Sensor Value: 0xFF

Notice : When the event triggered, the device will report the messages to the nodes in the group 1.

The messages also include the tamper status.

1.4 Power Up Procedure

1.4.1. NWI

When the device power on, the device will check is it already adding to the network? If

doesn't, press the button to start the NWI mode. Until timeout or the device successful to

inclusion by controller. NWI mode can be aborted by pressing the button 3 times.

1.4.2. Wake

When the device power on, the device will wake about 20 seconds. In this duration, the

controller can communicate with the device. Normally the device is always sleeping to save

the battery energy.

1.5 Over The Air (OTA) Firmware Update

The device supports the Z-Wave firmware update via OTA.

Let the controller into the firmware update mode, and then press the button once to start the

update.

Please don't remove the battery, otherwise it will cause the firmware broken, and the

device will no function.

After updated finish, it is recommended that the user power up the device.

Caution: After remove the battery, please wait about 30 seconds, and then re-install the

battery.

1. Overview

AirLive SI-104 User Manual

1.6 Security Network

The device supports the security function. When the device included with a security

controller, the device will auto switch to the security mode. In the security mode, the follow

commands need using Security CC wrapped to communicate, otherwise it will not

response.

COMMAND_CLASS_BATTERY

COMMAND_CLASS_NOTIFICATION_V4

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_SENSOR_BINARY_V2

COMMAND_CLASS_WAKE_UP_V2

1.7 Test Alarm

Test the sensor by pushing firmly on the test button for around 2 seconds until the horn

sounds, the sound pattern is 3 beeps, pause, and then 3 beeps with red LED flashing

continuously and rapidly, and the controller will receive Smoke alarm test notification. If the

Smoke Sensor beeps three with yellow LED flashing three times in 43 seconds, it indicates

the Smoke Sensor is not working properly, it requires to be repaired.

This is the only way to make sure that the Smoke Sensor device is working properly. If the

device fails to test properly, have it repaired or replaced immediately. If you suspect that

your Smoke Sensor does not go into alarm, test it by pressing the test button to ensure if it

works properly.

Notice : To keep the Smoke Sensor in good working condition, testing the device weekly is

necessary.

1.8 Tamper Switch Feature

If the Smoke Sensor is not mounted into the bracket properly, the tamper function is

triggered and the yellow LED is steadily on. You will hear temporal three sound with yellow

LED steadily on until Smoke Sensor is mounted back into bracket properly.

Indice

Altri manuali AirLive Sensore di sicurezza

AirLive

AirLive SI-102 Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente