airnet PTP600 series Manuale utente
Quick Installaon Guide
Package Contents:
Two Netkrom AIRNET Outdoor Bridge Units
Two Mounng brackets (include: 2 Wall/ Pole
mounng system and 4 screw nuts)
Two PoE Injectors
Two Power Cables
Two RJ45 Waterproof Connector System
CD-ROM
Two 75’ Outdoor Rated Cat5e shielded cables
300 Mbps PTP600 SERIES
4.9-5.8GHz MIMO Bridge Point to Point Kit
Warnings
Hardware
Installaon
1
Quick
Installaon
Guide
Do not work on the system or connect or disconnect cables during periods of lightning acvity.
NETKROM shall not be liable for incidental or consequenal damages resulng from the furnishing, performance, or use of
this manual.
Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into
contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they
may cause serious injury or death.
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
To meet regulatory restricons, the radio and the external antenna must be professionally installed. The network
administrator or other IT professional responsible for installing and configuring the unit must be a suitable professional
installer. Following installaon, access to the unit should be password protected by the network administrator to maintain
regulatory compliance.
The AIRNET Outdoor Bridge Point to Point kit and PoE injector can be damaged by incorrect power applicaon. Read and
carefully follow the installaon instrucons before connecng the system to its power source.
2
High Capacity Wireless Networks www.netkrom.com
300 Mbps PTP600 SERIES
Package contents
Hardware
Installaon
1
Quick
Installaon
Guide
Take a moment to ensure that you have all of the following parts in your Outdoor Waterproof Unit installaon kit before you
begin installing the product. If any parts are missing, please contact your local vendor or contact us, please see the contact
informaon in Secon 6.
3
www.netkrom.com
300 Mbps PTP600 SERIES
High Capacity Wireless Networks
Setup Requirements
Before starng, please verify that the following is available:
Hardware
Installaon
1
Quick
Installaon
Guide
CAT5/5e or FTP Outdoor Ethernet cable (from the PTP to PoE Injector).
At least one computer is installed with a Web browser and a wired or wireless
network interface adapter.
TCP/IP protocol is installed and IPaddress parameters are properly configured
on all your network’s nodes
4
www.netkrom.com
Important!
Configure and verify the PTP kit operaons first before you mount the unit in a
remote locaon.
You may need to install a lightning arrestor to protect your PTP kit from lightning.
For choosing the best locaon for your PTP choose an elevated locaon where
trees, buildings and large steel structures will not obstruct the antenna signals
and which offers maximum line-of-sight propagaon with the users.
300 Mbps PTP600 SERIES
High Capacity Wireless Networks
AIRNET Outdoor Bridge
Point to Point Installaon
Step 1:
Hardware
Installaon
1
Quick
Installaon
Guide
Connect one end of your UTP or FTP Outdoor cat.5 Ethernet
cable with waterproof connector to the RJ-45 connector located
in the PTP unit. Then connect the other end of the cable to the
PoE injector.
For the Netkrom PoE, the recommended length of the Category 5
cable is up to 260 feet or 80 meters.
1. Remove the thin enclosure nut from the feedthru assembly.
This can be discarded. Loosen the compression nut completely
5
www.netkrom.com
2. Insert the RJ45 connector through the feedthru assembly
3. Tighten the compression nut loosely to the feedthru assembly
enclosure nut
feedthru
assembly
compression nut
300 Mbps PTP600 SERIES
High Capacity Wireless Networks
Hardware
Installaon
1
Quick
Installaon
Guide
6
www.netkrom.com
4. Screw the enre feedthru assembly into the RJ45-ECS housing
which is already mounted in the PTP unit. There should be a
rubber gasket between the two assemblies. Tighten the
feedthru assembly to create a seal.
5. The final step is to ghten the compression nut unl the gaskets
are ght around the Cat5 cable. Always push the cable toward
the connector while ghtening to ensure good strain relief of
cable to connector.
Step 2:
From the PoE injector connect one cat.5 Ethernet cable to the radio
and another cat.5 cable to a switch or PC.
Step 3:
Connect the power cable supplied in the Netkrom PoE kit to the main
electrical supply and the power plug into the socket of the injector.
Now, turn on your power supply. Noce that the POWER LED has
lighted up. This indicates that the PTP unit is receiving power through
the Netkrom PoE Injector and that connecon between your AIRNET
PTP unit and your network has been established.
Note: Please use the PoE injector provided in the package. Using a
PoE with a different voltage rang will damage this product.
300 Mbps PTP600 SERIES
RJ45-ECS housing
RJ45-ECS housing
High Capacity Wireless Networks
Note
Hardware
Installaon
1
Quick
Installaon
Guide
7
www.netkrom.com
Mounng the AIRNET Outdoor
Bridge PTP in a Pole or Tower
The bracket in the illustraon side shows the normal orientaon which
allows the wireless unit to be pointed up towards the base staon
antenna. However, if you live somewhere that would require you poinng
the device down towards the base staon antenna (for example, you are
on the side of a mountain in view of the base staon antenna below),
reverse the bracket so the Netkrom wireless radio Unit can be “lted”
downward when you aim the AIRNET PTP in a later step.
Netkrom AIRNET PTP device can be mounted on the pole or tower as shown
in following:
1. Aach the mounng bracket to the back of the radio using the four hex
screws provided. (Do not over ghten the screws.)
Note Do not ghten the screws all the way because you will need to adjust the
AIRNET PTP direcon in a later step.
2. You can use the pipe bracket assembly for either thin or thick poles by just
inverng the posion of one of the elements as it shown on the right.
3. Mount the AIRNET PTP to the top of the pipe or other support and point
the AIRNET PTP in the approximate direcon of the base staon antenna,
then hand-ghten the nuts on the mounng system.
300 Mbps PTP600 SERIES
High Capacity Wireless Networks
8
www.netkrom.com
uConfig
Ulity2
Quick
Installaon
Guide
Using uConfig
When you execute the uConfig file you should see a window as it is
shown on the right side. Click yes to connue
The screen is divided into three secons. The top secon shows the
Ethernet adapter that is accessing the network device and the middle
poron shows the roung table associated with the Ethernet adapter.
In the lower window, a list of all uConfig compable devices on the
network is shown.
Highlight the device you desire to configure. Then click on the “Open
web” buon.
uConfig is a feature that provides the ability to directly access the AIRNET
PTP without the need to know absolutely its IP address. It may be run
directly from the product CD or installed on the user’s PC for later access.
300 Mbps PTP600 SERIES
High Capacity Wireless Networks
9
www.netkrom.com
uConfig
Ulity2
Quick
Installaon
Guide
Click the OK buon to connue
At the login prompt, enter the User name and Password. The default
are:
User name: admin
Password: password
Click on OK and start configuring the radio.
300 Mbps PTP600 SERIES
High Capacity Wireless Networks
10
www.netkrom.com
PC
Configuraon3
Quick
Installaon
Guide
If you don’t use the uConfig Ulity you need to establish Ethernet
connecon between your PC and the AIRNET PTP, by default the
AIRNET PTP has the IP address 192.168.168.1. Therefore, your PC must
be in the same network segment as the AIRNET PTP in order to get
Ethernet connecvity. The steps shown below are for Windows XP.
Step 1:
Go to Start buon, then go to My Network Places and finally
click on Network Connecons.
Right Click over your network adapter and select Properes.
Step 2:
Select the Internet Protocol Opon and then click in Properes.
Step 3:
Now configure the IP Address of your network adapter with
an IP in the same Network segment as your AIRNET PTP is as
it is shown in the picture, you don’t need to assign any
gateway address.
Press OK and then press the Close buon.
300 Mbps PTP600 SERIES
High Capacity Wireless Networks
Indice
Altri manuali airnet Router di rete
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza