Airwheel T5 Manuale utente
T5
User Manual
Thank you for buying the Airwheel T5.
Please read the product instructions carefully before
using the Airwheel T5 and follow all instructions, notes
and warnings in this manual. Failure to do so will result
in damage to the product and will not be covered by the
warranty.
Please keep the manual and warranty card in a safe place.
Packing List
Wakeboard
Paddle Pump w/ gauge
Toolbox
Repair kitFin
Charger 1Joystick 1Battery 1Handle 2
Safety magnetic clasp 1Wakeboard 1Toolbox 1Repair kit 1
Instruction manual 1Paddle 1Pump w/ gauge 1Fin 1
Electric paddle 1Base cover 1Water bae 1
PRODUCTS AND ACCESSORIES
ELECTRIC PADDLE
battery
Safety
pin
• Unpack and unroll your SUP on a smooth, clean, at surface.
• Connect the air tap on your pump to the ination valve on your SUP. Firmly pushthe air tap inwards and twist clockwise to
secure the connection.
• Before you begin to pump, please consult the recommended PSI on the valve(s) of your SUP and inate to the appropriate
value. DO NOT over-inate your SUP.
• The PSI may not register on your pump until you reach at least 7 PSI - keep pumping!
• Once the desired air pressure has been reached, please safely disconnect the air tap of your pump and secure the valve on
your SUP.
WARNING: Please only use the pump provided or other recommended pumps. DO NOT use an air compressor as you will risk over-
inating the board and severely damaging your SUP beyond repair. Your warranty will be void in the event of damage via over-ination.
OPERATION OF VALVES
In order to inate easily,Remove the valve cover(b)-clockwise whirl it(b), Put it(a)in “Output” position.
After inating,screw in valve cover(b) and anticlockwise whirl it(b).
阀门
INFLATABLE
1. The board can be inated either with our hand pump or an electric pump. The electric pump can inate the board to a moderate pressure and save
a lot of time with about 90% of the required air volume. You will need to use your hand pump to inate the chambers to the correct pressure.
2. Do not use an air compressor. Damage to your board caused by over ination from an air compressor is notcovered by your warranty.
3. After 2 or 3 days there may be a small decrease of pressure due to temperature change. If so, add a few pumps of air.
4. Before undertaking a long paddle, inate the board for a full 24 hours to be sure the board is airtight. If you are seeing a consistent decrease in air
pressure, follow the instructions for leak detection in the board repair sectionof this manual.
5. Do not over-inate the board. A max pressure of 12 PSI is adequate. The easiest gauge of a good workingpressure is to have the chambers inated
to a rm pressure when you press on them.
6. Do not pump to a high pressure and let the board sit out in the sun. If the board is going to be in a warm environment, slightly under-inate the
board and allow the heat from the sun to increase the internal pressure.When paddling, the colder temperature of the water may cause a slight loss
in chamber pressure. It is a goodidea to carry a pump with you so that you can add some air to the chambers if necessary.
Airwheel has chosen PVC to provide superior protection from ultraviolet light. However, to ensure extra years of exibility and bright colors, avoid storing
the board where it will be exposed to weather or in direct sunlight.
Please review the following list for storage and board care tips.
1. Before storing, hose o the board and let it dry completely to prevent mildew buildup.
2. Do not use harsh chemicals for cleaning. Most dirt can be removed with a mild soap and fresh water.
3. You may store the board inated or deated.if you deate the board, we recommend that you store it in theprotective bag that came with the board.
4. We do not recommend hanging the board.
5. Do not store in extreme conditions.(i.e. above 150F or below -10F)
6. Store in a clean, dry place.
BOARD CARE AND STORAGE
INFLATION TIPS AND PRECAUTIONS
FIN TYPE:
We have three ways to install ns, which can be
chosen according to the actual situation.
Your SUP either has a Bravo Fin or Smart Lock
Fin System. Please check your fin type and
follow the necessary instructions.
TIP: Before you begin please ensure the n box
slot is clean and free of sand and grit.
Slide the n into the
n box.Make sure n
and card slot of n
box in the same
position.
Slide the n into the
n box.Make sure n
and card slot of n
box in the same
position.
Place the bolt in the
chute and rotate
tightly to ensure that
the n do not fall o.
Insert the gasket into
the slot to ensure
that the gasket can
catch the n.
Unscrew the plate from the screw (Figure 1) and
place into the n slot via the gap (Figure 2).
TIP: Use the screw to slide the plate into place
along the slot.Insert the n into the n box slot
via the central gap, slide the n to the back and
rmly push down the other end (Figure 3).Line
up the screw with the screw plate and tighten
until fully secure (Figure 4).
FIN Screw Fin
Slide Fin
US Fin
Conne ct the thr uster
Base cover
Fixing plate
Quick
release
Base cover
Electric stand up paddle Fixing plate
Electric stand up paddle
1.
2.
3.
Indice
Manuali Attrezzatura nautica popolari di altre marche
Dowco
Dowco V322 CC - 2019 Manuale utente
Humphree
Humphree HCS-5 Manuale utente
Vetus
Vetus BOW4512D Scheda tecnica
Dock Doctors
Dock Doctors SLIDING BOARDING STEP Manuale utente
Mastervolt
Mastervolt Mass Combi 12/2000-100 Istruzioni operative originali
Zattini Group
Zattini Group bamar BOXTRON E14S Guida utente
