AITech MaxView Manuale utente

MaxView Cinema Kit

Quick Install Guide

INSTALLATION

Step 1 - Turn off your computer. Disconnect your monitor’s VGA cable from the

VGA card on the back of your computer.

Step 2 – Connect the MaxView’s VGA cable to VGA card on the back of your

computer.

Step 3 – (Optional) Connect your computer monitor to the VGA-Out connector on

the MaxView. If you are connecting to a laptop, you may not have a monitor to

connect in this step. Note that a computer monitor is not required to use the

MaxView.

Step 4 - Connect the MaxView to your TV, VCR, or projector using either the

composite video (RCA) or the S-Video*cable.

Step 5 - Plug the 5V AC power adapter into an AC outlet and connect the power

cord to the MaxView.

Step 6 - Turn on your computer and your TV set. If you do not see an image on

the TV (or projector), continue with the System Setup section below.

SYSTEM SETUP

The MaxView will work at any of the following display settings:

•640x480 at 60-85 Hz refresh rate

•800x600 at 60-75Hz refresh rate

•1024x768 at 60-70 Hz refresh rate

In Windows, these settings are made in Display Properties. To get to Display

Properties, right-click a blank area of your desktop, click Properties at the bottom

of the menu, and then click the Settings tab.

*Note: The S-Video connection is a newer video standard. This type of

connection improves color, clarity, and resolution. We recommend using the S-

Video connection whenever available.

Not all TV's have S-Video or RCA connectors. If your TV does not, you will need

to connect to another device (usually a VCR or a RF modulator) that will provide

the proper signal output to your TV. The scan converter does not provide a proper

signal for the antenna input of a TV (F-connector). See connector information on

next page.

CONNECTOR TYPES

S-Video or S-VHS (Best)

This is a 4-pin DIN connector. The S-Video

signal will give you the best TV image. It is not

found on all TV's or VCR's. Use this cable if

you have the connection available on your video

device. The S-Video connection provides the

highest quality signal.

RCA / Composite (Good)

This connector carries the composite video

signal. If your TV does not have direct video

inputs, you will have to connect the scan

converter to your VCR or RF modulator. The

RCA/Composite connection provides a good

quality signal.

F Connector (Poor)

This is a threaded connector used to connect an

antenna or cable box to the TV or VCR. The F

connector is for RF (radio frequency) signals

only. If your TV only has this type of

connection, you will need to convert the

RCA/Composite signal to RF before you can

view it on your TV. A VCR or a RF-Modulator

(available at Radio Shack) can be used to

convert the signal. The RF connection provides

the lowest quality signal.

IMAGE QUALITY

Several factors affect the quality of the TV image.

The TV standard (NTSC, PAL, or SECAM) cannot match the higher image quality

achieved by PC monitors. Small text and numbers do not display very well on a

TV. Graphic images usually display much better. Therefore, the type of image

being displayed is a determining factor of how well it will be displayed.

Be sure to view the actual application you wish to display on the TV before making

any adjustments. Other screens may not appear the same on the TV.

TELEVISION

•Some TV’s will have better quality than others (not always determined by cost)

•Use the S-Video (S-VHS) connection, whenever possible.

•Adjust for color, sharpness, contrast, and brightness for best image.

ADJUSTING FONTS

If your display has smaller text and numbers, the following suggestions may help:

In Windows, you can specify the font you use for the different areas of the

Windows Desktop. To get to your Display Properties just right-click a blank area

of your desktop - click Properties at the bottom of the menu - and click the

Appearance tab at the top of the dialog box as shown on the next page.

The graphic below shows how to set the font for the different areas of Windows.

The example shows how to change the size of the Desktop Icon font:

Select Icon from the Item pull-down list.

The graphic on the next page shows you how to change the size of the font. Select

the size you think will work and click the Apply button. If this setting is not

suitable for your needs, choose one higher or lower that you like better. Note that

the default font size is 8-point text. Standard printed text is 12-point. The list goes

up to 18-point text but this setting may be too large.

Note: The Scheme selection from the Appearance screen also allows you to adjust

font sizes in other areas of Windows.

INTERNET EXPLORER

You can select a larger font for displaying the Internet pages you are showing on

the TV. Click View - Fonts - and select a larger font for better viewing. Note that

Medium is the default font size for the normal screen view.

Connections:

•Check the power connection to the scan converter.

•Check the connections from the scan converter to the PC.

•Check the connections from the scan converter to the TV.

TV (or VCR):

•RCA connections to a TV or VCR must be to the Video Input (yellow)

connector.

•If you are connected directly to a TV with a S-Video or RCA cable, ensure

that the TV has been configured to accept auxiliary video input.

•If you are connected to the TV through a VCR, ensure that the TV and VCR

have been configured to accept auxiliary video input.

An input button on the TV or VCR’s original remote control often sets the video

input mode. This mode is needed for both S-Video and RCA video connections.

The button may be marked Video, Video-1, Aux, Input, Vid, Line, Line-In,

TV/VCR, etc. On some TV’s and VCR’s this setting is made by selecting Channel

2, then pressing the Down Channel button. If this does not work, refer to your TV

(or VCR) owner’s manual.

Settings: Check that the computer’s Display Settings are set correctly.

o640x480 at 60-85Hz

o800x600 at 60-75Hz

o1024x768 at 60-70Hz

Laptops: Laptops must be set to External-only or Simultaneous VGA display

mode. This is usually done with a hot-key combination (Fn + function key). Refer

to your laptop manual for further details.

Still Having Problems:

•Check our Web site www.aitech.com for more information.

AITech International Corporation

Website: http://www.aitech.com

HELP!! I CAN'T SEE

ANYTHING ON MY TV!

Cinema Kit

User’s Guide

For IBM Compatibles - All Windows Versions

Information in this document is subject to change without notice. No part of this document may be

reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying

and recording, for any purpose without the prior written permission of AITech International Corporation.

MaxView is a trademark of AITech International Corporation.

Pentium is a trademark of Intel Corporation.

IBM is a registered trademark of International Business Machines Corporation.

MS-DOS and Microsoft are registered trademarks and Windows is trademark of Microsoft Corporation.

AITech International Corporation World Headquarters

1288 Kifer Rd, Suite 203

Sunnyvale, CA 94086

USA

E-mail: [email protected]om

Website: www.aitech.com

Introduction

Welcome to the world of the MaxView. This multimedia product is a convenient tool for business

conferences, classroom presentations, multimedia demonstrations and home entertainment. It is capable of

displaying your computer images onto the television, or any video product such as a VCR or camcorder.

Product Features

MaxView offers the following features:

•External VGA-to-TV digital scan converter

•Superior image quality with resolutions up to 1024x768. Wider horizontal and vertical (up to 85Hz) frequencies

•Simultaneous display on personal computer monitor (or laptop LCD) and TV screen

•Plug & Play. No settings to make in your system

•Patented Flic-FreeTM filter technology for sharper flicker-free images on your TV screen

•3 channel 10-bit output D/A converter

•Simultaneous RCA composite and S-Video outputs

•Default underscan

•FCC Class B certified and CE Conformance verified

Input

•15-pin VGA analog RGB signal

•Multiple input frequencies

o640x480 @ 60-85 Hz

o800x600 @ 60-75 Hz

o1024x768 @ 60-70 Hz

Output

•S-Video & RCA (cables included)

•VGA bypass

•SCART (optional cable for the PAL MaxView)

Power Requirement

•5 volts DC, 800 mA, center negative polarity (AC adapter included)

Minimum System Requirements

•IBM AT or better PC, other PC compatible computer, or Mac computer (with compatible refresh rate)

•MS-DOS or any version of Windows

•VGA-Out port at 640x480 resolution and 16 colors

•Video input device such as video monitor, TV, or VCR

Package Contents

The following items are included in the MaxView package:

•MaxView Scan Converter

•MaxView Quick Start Guide

•20’ Composite (RCA) Video cable

•20’ S-Video cable

•20’ Audio Cable

•5V AC power adapter (center negative polarity)

Installing the MaxView Cinema Kit

The MaxView is totally plug-and play. Installation is simple and straightforward. There is no need to

install any device driver. Just follow these steps:

1. Turn off your computer.

2. Disconnect your monitor’s VGA cable from the VGA port on the rear of the computer.

3. Connect the MaxView’s 15-pin VGA connector to the VGA port where the monitor was connected.

(You may choose to connect the PC monitor to the VGA pass-thru port on the MaxView for

simultaneous display on your PC monitor.)

4. Choosing the S-VIDEO* or RCA video cable, connect one end to the appropriate port on the MaxView,

and the other end to the corresponding port on the TV.

5. Plug in the power adapter.

6. Power on your PC.

That’s all there is to it! You should now be able to see your computer image displayed on the TV screen,

LCD projector, VCR, or video camcorder. There is no need to change any settings unless your computer’s

VGA output is set at a refresh rate higher than 70Hz.

Adjust your Display Properties refresh rate. We suggest that you use one of the

following refresh rates:

70 Hz (Hertz) for 1024x768 resolutions

75 Hz (Hertz) for 800x600 resolutions

85 Hz (Hertz) for 640x480 resolutions

*Note: The S-Video connection is a newer video standard. This type of connection

improves color, clarity, and resolution. We recommend using the S-Video connection

whenever available.

Help! I Can’t See Anything On My TV!

If you are having difficulty seeing your computer display on the TV, check the following:

Connections:

•Check the power connection to the MaxView.

•Check the connections from the MaxView to the PC.

•Check the connections from the MaxView to the TV.

TV (or VCR):

•RCA connections to a TV or VCR must be to the Video Input (yellow) connector.

•If you are connected directly to a TV, ensure that the TV has been configured to accept auxiliary video

input.

•If you are connected to the TV through a VCR, ensure that the TV and VCR have been configured to

accept auxiliary video input.

An input button on the TV or VCR’s original remote control often sets the video input mode. This mode is

needed for both S-Video and RCA video connections.

The button may be marked Video, Video-1, Aux, Input, Vid, Line, Line-In, TV/VCR, etc. On some TV’s

and VCR’s this setting is made by selecting Channel 2, then pressing the Down Channel button. If this does

not work, refer to your TV (or VCR) manual.

Settings: Check that the computer’s Display Settings are set correctly.

o640x480 at 60-85Hz

o800x600 at 60-75Hz

o1024x768 at 60-70Hz

Laptops: Laptops must be set to External-only or Simultaneous VGA display mode. This is usually

done with a hot-key combination (Fn + function key). Refer to your laptop manual for further details.

Contacting AITech Technical Support

You may find it most convenient to visit our website anytime at www.aitech.com. The Technical Support

area of this site contains the very latest information on product usage and troubleshooting.

If you require our assistance to resolve problems with the product, please e-mail our Technical Support at

[email protected].

Indice

Altri manuali AITech Accessori TV

AITech

AITech ProPC/TV Wireless Manuale utente

Manuali Accessori TV popolari di altre marche

pass & seymour

pass & seymour GFCI Manuale utente

Skyvue

Skyvue SECURITY ALARM DEVICE Manuale utente

Niles

Niles C5-RFWM Manuale utente

Philips

Philips SWA3554 Manuale utente

Sony

Sony CRU-52X1 Manuale utente

Sony

Sony BRAVIA KDL-46Z4100/S Guida

BVE

BVE MATRIX 7xe Manuale utente

Epson

Epson Moverio BT-100 Manuale utente

Philips

Philips MONCARD Manuale utente

Alcatel

Alcatel onetouch v100 Manuale utente

Flow

Flow 836 ONT Manuale utente

AIRIS

AIRIS G819 Manuale utente

Philips

Philips LC7.1E Manuale utente

Loewe

Loewe Digital Recorder + Manuale utente

Sceptre

Sceptre Stello Manuale utente

Philips

Philips Flavors 42FDF7013 Manuale utente

Goodmans

Goodmans GD11FVRSD32 Manuale utente

Philips

Philips Clon99-BKI Manuale utente