AJA D10AD Manuale utente

D10AD

10-bit Analog to SDI

Converter

User Manual

September 2, 2005 P/N 101639-00

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

AJA D10AD 10-bit Component/Composite to SDI Converter User Manual — Introduction

Introduction

The D10AD provides excellent quality 10-bit conversion of component or

composite analog video to SDI—with EDH. The D10AD accepts YPbPr (SMPTE,

EBU-N10), Betacam, or RGB component inputs and NTSC/PAL or YC (S-Video)

composite inputs. When using composite sources, the D10AD offers a 4-Line

Adaptive Comb Filter for high quality decoding. The comb ﬁlter can be switched to

2-line or notch modes for minimum delay requirements. NTSC/PAL conﬁguration

is automatic. Video format, AGC, H/V blanking, and pedestal are all user

conﬁgurable via dipswitches.

Note:

The D10AD requires a Time Base Correct source. Operation is not

recommended from VTRs, laser disks, etc., without Time Base Correction (TBC).

Features

•

Excellent-Quality 10-bit Universal A/D Conversion

•

Component, Composite or Y/C Analog Input

•

4-Line Adaptive Comb Filter

•

Full 10-bit Data path, 2x Oversampling

•

YPbPr, Betacam, or RGB Component Formats

•

Composite NTSC or PAL

•

AGC mode

•

4 SDI outputs with EDH

•

Color Bar Generator

•

External DIP switch user interface for configuration

Block Diagram

D10AD 10-bit Analog Component and Composite to SDI Converter, Block

Diagram

DIP

Switch

User

Interface

for

Feature

Selection

10-bit A/D

Converter

Sync

Lock

Comb

Filter

Serial Video Out 1

Serial Video Out 2

Serial Video Out 3

Serial Video Out 4

COMPONENT/COMPOSITE

INPUTS (selected by DIP switch)

COMP

I/O Connections

D10AD, Side View

User Controls

The user interface for the D10AD is an 8-

switch DIP accessible through a cut-out in the

bottom of the unit. Use the DIP switches to

conﬁgure outputs, pedestal, blanking, and

enable or disable comb ﬁlter, EDH, AGC, and

test pattern.

Switches 1 and 2 select composite or

component input and the type of component

input. Switches 3 through 8 set conﬁguration

features. The exact function of each DIP

switch and what it controls is described on the

following pages.

Note:

Changing input format (SW1, SW2, or SW3) causes a reset to occur that

takes about 10 seconds to complete.

+ 5VDC

Power

Input

Serial

Digital

Outputs

4 BNCs

Composite/

Component

Inputs

Conﬁguration

determined by

DIP switch on

other side of

Converter

DIP Switches

OFF ON

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

AJA D10AD 10-bit Component/Composite to SDI Converter User Manual — User Controls

Switch 1—Selects Component or Composite input from the Compos-

ite/Component BNCs

Switch 2—Configure Type of Component input from the Composite/

Component BNCs

Switch 3—Configure Pedestal For Output BNCs (disabled in PAL)

Switch 4—Configure Blanking—Not Currently Implemented

The convertor defaults to narrow blanking.

Switch 5—Turn Comb Filter ON or OFF

Switch 6—Configure EDH Insertion

ON OFF

Selects Composite input. Selects Component input.

ON OFF

RGB Input (If SW1 is OFF) or Composite

Input (If SW 1 is ON).

YPbPr Input (If SW1 is OFF) or

Y/C (S-VIDEO) (If SW1 is ON().

ON OFF

If set for COMPOSITE Input:

Pedestal is removed on inputs with 7.5 IRE

Pedestal

If set for COMPONENT Y/Pb/Pr Input:

Sets BETACAM levels

If set for COMPOSITE Input

For inputs without Pedestal

If set for COMPONENT Y/Pb/Pr:

Sets SMPTE/EBU-N10 levels

If set for COMPOSITE Input:

Pedestal is removed on inputs with 7.5 IRE

Pedestal

If set for COMPONENT Y/Pb/Pr Input:

Sets Japan BETACAM levels

If set for COMPOSITE Input

For inputs without Pedestal

If set for COMPONENT Y/Pb/Pr:

Sets SMPTE/EBU-N10 levels

ON OFF

Notch Filter on (Comb Filter off) Comb Filter on (Notch Filter off)

ON OFF

EDH not inserted EDH inserted

Switch 3 Settings for

BETAJ Version of

D10AD

Switch 3 Settings for

Standard Version of

D10AD

Switch 7—Configure Automatic Gain Control (AGC)

Switch 8—Turn Test Pattern Output ON/OFF

Installation

Typically, D10AD installation consists of the following:

disconnect +5VDC from the convertor

conﬁgure the DIP switch for the desired equipment conﬁguration and video formats

connect video equipment to the convertor BNCs

apply +5VDC power to the converter (AJA power supply model DWP)

Specifications

ON OFF

Automatic Gain ON Automatic Gain Off (Unity Gain)

ON OFF

Internal color bars are output Disables test pattern output (normal video

operation)

Item Speciﬁcation

Serial Outputs SDI (SMPTE 259M) w/EDH

All outputs are separately buffered

4 x BNC

Frequency Response Y +/-0.15db to 5.5 Mhz

C +/-0.15db to 2.5 Mhz

2T K factor Less than .5% K Factor (2T)

Differential Gain < 1%

Differential Phase < 1 degree

A/D Converters 10 bits, 2X oversampling

User Controls Selectable By External Dip Switch:

Input Video Format

Pedestal Present/Not Present

Narrow/Wide Blanking

AGC On/Off

EDH On/Off

Test Pattern

Power

(AJA power supply model DWP)

5v DC regulated, 4 watt

Size 147 x 79 x 25 mm (5.8" x 3.1" x 1")

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com

Indice

Altri manuali AJA Convertitore multimediale

AJA

AJA HA5-Fiber Istruzioni operative

AJA

AJA FiDO 12G Series Istruzioni operative

AJA

AJA HD10AM Istruzioni operative originali

AJA

AJA 3G-AM-BNC Istruzioni operative originali

AJA

AJA HA5-4K Istruzioni operative

AJA

AJA HA5-4K Guida all'installazione

AJA

AJA Hi5-3D Istruzioni operative

AJA

AJA OG-DANTE-12GAM Istruzioni operative

AJA

AJA 12G-AM Istruzioni operative

AJA

AJA ROI Istruzioni operative originali

AJA

AJA U-TAP Series Istruzioni operative

AJA

AJA V2Digital Istruzioni operative originali

AJA

AJA HA5-Plus Istruzioni operative

AJA

AJA hi5-4k-plus Istruzioni operative

AJA

AJA hi5-4k-plus Istruzioni operative

AJA

AJA BRIDGE LIVE Istruzioni operative

AJA

AJA OG-ROI Series Istruzioni operative

AJA

AJA HDP2 Manuale utente

AJA

AJA T-TAP Manuale utente

AJA

AJA HD10MD3 Manuale utente

AJA

AJA FS-HDR Manuale utente

AJA

AJA FS2 Guida alla risoluzione dei problemi

AJA

AJA FiDO Series Istruzioni operative

AJA

AJA IPT-1G-SDI Istruzioni operative

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente